Sauder 422357 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-27
Français pg 28-31
Español pg 32-36
Lot # 510604 11/09/17
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Welcome to the
big kid desk.
Sit/Stand Desk
Model 422357

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
3-5
6-27
28-31
32-36
37- 38
39
Skip the power trip.
This time.
Short Screwdriver
422357 www.sauder.com/servicesPage 2
Adjustable Wrench

åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
Part Identification
A RIGHT END (1)
B LEFT END (1)
C MODESTY PANEL (1)
D SHELF (1)
E2 UPRIGHT (1)
F2 LIFT TOP BACK (1)
G LIFT TOP LEFT END (1)
H LIFT TOP RIGHT END (1)
I LIFT TOP (1)
A
B
C
D
E2
F2
G
H
I
Hardware Identification
(EXTENSION SET SHOWN SEPARATED)
EXTENSION RAIL - 2
JEXTENSION SLIDE - 2 K7F TWIST-LOCK®
FASTENER - 21
ROD - 1
26A
422357www.sauder.com/services Page 3
16E LEVELER - 4

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
COTTER PIN - 2
19M RACK TENSIONER - 2
121M
ACTUATOR PULL - 1
120M
WHEEL - 2
123M
LEFT AND RIGHT RACK
DRIVE SET - 1
122M CYLINDER - 1 124M
PROPEL NUT - 4
14M
GROMMET CAP - 1
1P
61P TWIST-LOCK®
FASTENER COVER - 12 62P MINI TWIST-LOCK® COVER - 1 65P CORD MANAGER - 2
SCREW COVER - 4
20P
METAL PIN - 2
1R
CORD CLIP - 2
9P GROMMET - 3 10P
32G LEVELER
BRACKET - 4 CABLE BRACKET - 1
72G
CYLINDER BRACKET - 2
71G
13F MINI TWIST-LOCK®
FASTENER - 1
422357 www.sauder.com/servicesPage 4
NUT - 4
24M
WASHER - 4
13M

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 9/16" PAN HEAD SCREW -14
51S
BLACK 9/16" LARGE HEAD SCREW - 12
1S BROWN 7/16" LARGE HEAD SCREW - 2 6S
BROWN 1-1/2" FLAT HEAD SCREW - 6
14S SILVER 5/8" FLAT HEAD SCREW - 20 23S
BLACK 1-15/16" FLAT HEAD SCREW - 5
113S
422357www.sauder.com/services Page 5
BLACK 1-1/4" MACHINE SCREW - 4
93S

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (7F) into the large holes in the MODESTY
PANEL (C), SHELF (D), UPRIGHT (E2), and LIFT
TOP ENDS (G and H).
422357 www.sauder.com/servicesPage 6
G
H
Do not tighten the TWIST-LOCK® FASTENERS in this step.
(21 used)
7F
7F 7F
D
E2
C
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1933
to watch a video on how to assemble your unit.

å Fasten the LEFT RACK DRIVE to the LIFT TOP LEFT END (G) and
the RIGHT RACK DRIVE to the LIFT TOP RIGHT END (H). Use
fourteen BLACK 9/16" PAN HEAD SCREWS (51S).
å NOTE: Be sure to use the exact holes with dashed lines.
Step 2
G
H
The LEFT RACK
DRIVE will have an
L stamped here.
The RIGHT RACK
DRIVE will have an
R stamped here.
BLACK 9/16" PAN HEAD SCREW
(14 used in this step)
51S
422357www.sauder.com/services Page 7
These edges must be even.

Step 3
å Push a SAUDER MINI TWIST-LOCK® FASTENER (13F) into
the hole in the LIFT TOP BACK (F2).
Do not tighten the MINI TWIST-LOCK® FASTENER in this step.
13F
F2
422357 www.sauder.com/servicesPage 8

å Fasten the LIFT TOP BACK (F2) to the LIFT TOP (I).
Tighten the MINI TWIST-LOCK® FASTENER.
Step 4
How to use the SAUDER TWIST-LOCK® FASTENER
and MINI TWISTLOCK® FASTENER
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
F2
I
This large hole
must be here.
Surface with MINI TWIST-LOCK® FASTENER
Surface with holes
422357www.sauder.com/services Page 9
Remember:
Righty tighty.
Lefty loosey.
Meet Part (I). This component has
been engineered to be lighter, stronger,
faster… well ok. Not technically faster.
But definitely makes for a sturdier Sit/
Stand Desk that’s easier to assemble
and friendlier to the environment.

å Fasten the LIFT TOP ENDS (G and H) to the LIFT TOP BACK (F2).
Use six BROWN 1-1/2" FLAT HEAD SCREWS (14S).
å Fasten the LIFT TOP ENDS (G and H) to the LIFT TOP (I). Tighten
six TWIST-LOCK® FASTENERS.
Step 5
H
G
BROWN 1-1/2" FLAT HEAD SCREW
(6 used in this step)
14S
14S
I
F2
422357 www.sauder.com/servicesPage 10
Surface with TWIST-LOCK® FASTENERS
Surface with TWIST-LOCK® FASTENERS