Sauder Barrister Lane Storage Credenza 414721 User manual

PLEASE CONTACT US
BEFORE RETURNING
YOUR UNIT TO THE STORE
1-800-523-3987
www.sauder.com
Made in the USA
Archbold, OH
NOTE: THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Lot #: 350044 04 / 05 / 13
Date Purchased: ____________________
English.................... Page 1-22
Français...............Pages 23-25
Espanol.............Páginas 26-28
414721
Storage Credenza
Barrister Lane Collection

ASSEMBLY TOOLS REQUIRED
Hammer
No. 2 Phillips Screwdriver
Tip Shown Actual Size
ADULT ASSEMBLY REQUIRED
TABLE OF CONTENTS
Part Identification.......................3
Hardware Identification .............4
Assembly Steps....................5-22
Français..............................23-25
Espanol...............................26-28
Safety .................................29-30
Warranty...................................31
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury
or death. ATV that is too large for the available space might be accidentally pushed or bumped off the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 135 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
WARNING
19"
70"
135 lbs.
Page 2 www.sauder.com/services 414721

PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked
letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help
identify similar parts.
A END 2
B UPRIGHT 1
C TOP 1
D BOTTOM 1
E BACK 2
F CENTER BACK 1
G LARGE BACK 2
H DOOR 2
I INNER DOOR 2
J ADJUSTABLE SHELF 2
K RIGHT BASE 1
L LEFT BASE 1
M BASE 1
N FRONT MOLDING 1
O RIGHT MOLDING 1
P LEFT MOLDING 1
Q END MOLDING 2
R UPRIGHT MOLDING 1
S SHELF MOLDING 2
T BRACE 2
Page 3
www.sauder.com/services414721
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
RS
T
A
E
G
H
I
JQ
S
T

HARDWARE IDENTIFICATION
Screws are shown actual size. You may receive extra hardware with your unit.
Page 4 www.sauder.com/services 414721
WARNING
Never use this furniture with a TV that is too
large or too heavy. Severe injury or death
can occur.The TV and furniture will be
unstable and may tip.
-The TV must less than 135 lbs.
-The base of the TV must be able to sit
completely on this shelf.
-Refer to instruction book for complete safety
information.
Note: This is a permanent label. Do not try
to remove. Surface will be damaged.
02/ 02 2 6 9 2 3 2 269232
WARNING LABEL - 1
4L
(Refer to the last step for proper location and application)
3M ANTI-SKID PAD - 1
FOOT - 1
23E
27H HINGE - 8
BLACK 9/16" LARGE HEAD SCREW - 93
1S
METAL BRACKET - 6
4G
NAIL - 16
1N METAL PIN - 14 1R RUBBER SLEEVE - 8 2R
CAM SCREW - 12
8F
HIDDEN CAM - 24
1F
BLACK 1-7/8" FLAT HEAD SCREW - 6
2S
SAFETY BRACKET - 1
1G
SMALL MAGNETIC
CATCH - 2
2I STRIKE PLATE - 4 6I
BLACK 1/2" FLAT HEAD SCREW - 4
11S
SILVER 1-1/2" MACHINE SCREW - 2
95S
BLACK 9/16" PAN HEAD SCREW - 4
51S
MAGNETIC CATCH - 2
12I
SILVER 5/8" MACHINE SCREW - 4
15S
TWIST-LOCK®
FASTENER - 2
10F
CAM COVER - 14
13P
CAM DOWEL - 12
2F
33M DECORATIVE
END - 4 34M DECORATIVE
BACKPLATE - 2
69K DECORATIVE
KNOB - 2
39M DECORATIVE
POST - 4
CORNER BRACKET - 4
31G

Look for this icon. It means a video
assembly tip is available at:
www.sauder.com/services/tips
1
1
S
t
e
p
Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (10F) into the large holes in the MOLDINGS (O and P).
Page 5
www.sauder.com/services414721
Do not tighten the TWIST-LOCK® FASTENERS in this step.
10F
O
P

2
2
S
t
e
p
Page 6 www.sauder.com/services 414721
Push twenty-four HIDDEN CAMS (1F) into the ENDS (A), UPRIGHT (B), BOTTOM (D), and BRACES (T). Then, insert the metal
end of a CAM DOWEL (2F) into each HIDDEN CAM, except the short edges of the ENDS (A) and BRACES (T).
Do not tighten the HIDDEN CAMS in this step.
Arrow
(12 used)
(24 used) Arrow
Arrow
Arrow
1F
1F
1F
1F
2F
2F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
A
A
B
D
T
T
Do not insert CAM
DOWELS into these edges.
Do not insert CAM
DOWELS into these edges.
Do not insert CAM
DOWELS into these parts.

3
3
S
t
e
p
Page 7
www.sauder.com/services414721
Turn twelve CAM SCREWS (8F) into the BASES (K and L) and MOLDINGS (N, O, and P).
8F
K
L
N
O
P
(12 used)

Fasten the END MOLDINGS (Q) to the ENDS (A). Tighten four HIDDEN CAMS.
Fasten the BASES (K and L) to the ENDS (A). Tighten four HIDDEN CAMS.
4
4
S
t
e
p
Page 8 www.sauder.com/services 414721
Caution
Risk of damage or
injury. Hidden Cams
must be completely
tightened. Hidden
Cams that are not
completely tightened
may loosen, and parts
may separate.
To completely tighten:
Start Tighten
Arrow
Arrow
Maximum
210 degrees
Minimum
190 degrees
A
A
Q
Q
K
L
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
These holes
must be here.
Angled edge
Angled edge
This END (A) will now be
called the LEFT END (A).
This END (A) will now be
called the RIGHT END (A).

Fasten the MOLDINGS (O and P) to the TOP (C). Tighten two TWIST-LOCK®FASTENERS.
5
5
S
t
e
p
Page 9
www.sauder.com/services414721
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must remain
fully inserted in the hole of the adjoining part while
locking the FASTENER.
2. Tighten the FASTENER with a Phillips screwdriver
as tight as possible.
Dowel end
C
P
O
Surface with holes
Long finished edge

6
6
S
t
e
p
Page 10 www.sauder.com/services 414721
Fasten two CORNER BRACKETS (31G) to the MOLDINGS (O and P) and TOP (C). Use eight BLACK 9/16" LARGE HEAD
SCREWS (1S).
Fasten two METAL BRACKETS (4G) to the TOP (C). Use two BLACK 9/16" LARGE HEAD SCREWS (1S).
Fasten the FRONT MOLDING (N) to the TOP (C) and MOLDINGS (O and P). Use six BLACK 9/16" LARGE HEAD
SCREWS (1S) through the METAL BRACKETS (4G) and CORNER BRACKETS (31G) and into the FRONT MOLDING.
C
P
O
N
BLACK 9/16" LARGE HEAD SCREW
(16 used for the BRACKETS)
1S
4G
31G
31G