Sauder Summit Station 425014 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
Share your journey!
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-523-3987.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Lot # 533122 10/24/19
Purchased: __________________
English pg 1-32
Français pg 33-36
Español pg 37-40
L-Desk
Summit Station Collection | Model 425014
Sit and surf.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4-5
6-32
33-36
37-40
41-42
43
425014 www.sauder.com/servicePage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
D BOTTOM (1)
D14 RIGHT DRAWER SIDE (1)
D15 LEFT DRAWER SIDE (1)
D78 DRAWER BACK (1)
D716 DRAWER BOTTOM (1)
E LONG MODESTY PANEL (1)
F DRAWER FRONT (1)
G SHORT MODESTY PANEL (1)
H LEFT BACK (1)
J FRONT/BACK MOLDING (2)
K RIGHT BACK (1)
L RIGHT FRONT PEDESTAL LEG (1)
M LEFT BOTTOM MOLDING (1)
N BRACE (1)
O LEFT BRACE (1)
P SHORT BRACE (1)
Q LONG BRACE (1)
RLEFT FRONT/RIGHT REAR
PEDESTAL LEG (2)
S RIGHT BOTTOM MOLDING (1)
T LEFT REAR PEDESTAL LEG (1)
U LEFT FRONT LEG (1)
V LEFT REAR LEG (1)
W LONG TOP (1)
X SHORT TOP (1)
425014www.sauder.com/service Page 3
D14
D15 D78
D716
A
C
B
D
E
F
G
H
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
R
J

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
425014 www.sauder.com/servicePage 4
(EXTENSION SET SHOWN SEPARATED)
EXTENSION RAIL - 2
35MA EXTENSION SLIDE - 2 35MC FILE GLIDE - 2
4B10A SLIDE CAM - 2
HIDDEN CAM - 45
1F CAM DOWEL - 23 2F CAM SCREW - 22 8F WOOD DOWEL - 13 15F
CROSS SLOTTED
DOWEL - 4
24F PLATE - 3 41G PULL - 1
35K GLUE - 1 54M
GROMMET CAP - 2
1P GROMMET - 2 10P SCREW COVER - 5 74P CAM COVER - 27 75P

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
425014www.sauder.com/service Page 5
BLACK 9/16" LARGE HEAD SCREW - 12
1S 3S GOLD 5/16" FLAT HEAD SCREW - 8
SILVER 1-1/8" FLAT HEAD SCREW - 2
10S 30S BLACK 1-9/16" FLAT HEAD SCREW - 4
BLACK 7/8" MACHINE SCREW - 2
37S BLACK 2-3/8" FLAT HEAD BOLT - 4
103S
BLACK 1-15/16" FLAT HEAD SCREW - 5
113S

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push twenty-three HIDDEN CAMS (1F) into the ENDS (A
and B), UPRIGHT (C), MODESTY PANELS (E and G), and
BRACE (N). Then, insert the metal end of a CAM
DOWEL (2F) into each HIDDEN CAM.
Look for this icon. It means a
video assembly tip is available at
www.sauder.com/service/tips
425014 www.sauder.com/servicePage 6
A
C
B
E
G
N
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tighten the HIDDEN CAMS in this step.
Arrow
1F
2F
(23 used)
Metal end
1F
2F
Metal end
Arrow
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole

å Push twenty-two HIDDEN CAMS (1F) into the ENDS (A
and B), UPRIGHT (C), BOTTOM (D), LONG MODESTY
PANEL (E), MOLDINGS (M and S), and LEFT BRACE (O).
Step 2
425014www.sauder.com/service Page 7
A
C
B
E
D
M
O
S
(22 used)
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
1F
Arrow
1F
Arrow
1F Arrow
1F
Arrow

å Turn twenty-two CAM SCREWS (8F) into the RIGHT END (A),
MOLDINGS (M and S), and LEGS (L, R, T, U, and V).
å NOTE: Be sure to use the exact holes shown.
Step 3
425014 www.sauder.com/servicePage 8
A
L
M
R
S
T
U
V
R
8F
(22 used)

Step 4
425014www.sauder.com/service Page 9
åFirst, fill the holes in the LEGS (U and V) 1/4 to 1/2 full with
GLUE (54M). Then, insert the WOOD DOWELS (15F) into the
holes. Wipe away the excess GLUE.
åNow, fill the holes in the UPRIGHT (C) and LEFT BRACE (O) 1/4
to 1/2 full with GLUE.
åFasten the LEGS (U and V) to the UPRIGHT (C) and LEFT
BRACE (O). Tighten six HIDDEN CAMS.
åNOTE: Be sure the WOOD DOWELS in the LEGS insert into the
UPRIGHT and LEFT BRACE. Wipe away the excess GLUE.
C
O
U
V
Fill the holes 1/4 to 1/2 full with GLUE.
Inspect the parts thoroughly before
assembling. Disassembly of glued
parts is extremely dicult.
Caution
!
54M
15F
1
2
Surface
with
HIDDEN
CAMS
These surfaces
should be even.
Edge with
CAM DOWELS
15F
Surface
with
HIDDEN
CAMS

Step 5
425014 www.sauder.com/servicePage 10
å Fasten the LEGS (L and R) to the RIGHT END (A)
and RIGHT BOTTOM MOLDING (S). Tighten six
HIDDEN CAMS.
å NOTE: Position the RIGHT BOTTOM MOLDING (S)
exactly as shown.
A
L
S
R
Surface
with
HIDDEN
CAMS
These surfaces
should be even.
Edge with
CAM DOWELS
Surface
with
HIDDEN
CAMS
The CAM SCREWS
are closer to this edge.

Step 6
425014www.sauder.com/service Page 11
A
å Separate the EXTENSION SLIDES (35MC) from the EXTENSION RAILS (35MA) as shown in the upper diagram
below. Be prepared, the parts are greasy.
å Fasten one EXTENSION RAIL (35MA) to the RIGHT END (A). Use two GOLD 5/16" FLAT HEAD SCREWS (3S)
through holes #1 and #3.
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the
inner cartridge of the EXTENSION RAIL in to find the other hole that lines up with the hole in the END. Turn a
SCREW into this hole.
å NOTE: The EXTENSION SLIDES (35MC) will be used later for the DRAWER.
Open end
Push the black lever in and pull the SLIDE from the RAIL.
35MA
35MC
1
2
3
GOLD 5/16" FLAT HEAD SCREW
(2 used for the RAIL)
3S
The CAM SCREWS
must be here.

å Fasten the LONG MODESTY PANEL (E) to the LEFT END (B).
Use two BLACK 1-15/16" FLAT HEAD SCREWS (113S).
Step 7
425014 www.sauder.com/servicePage 12
B
E
BLACK 1-15/16" FLAT HEAD SCREW
(2 used in this step)
113S
Edge with CAM DOWELS
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
Curved edge

å NOTE: This step shows a dierent view of the PANEL (E).
å Fasten the LONG MODESTY PANEL (E) to the LEFT
REAR PEDESTAL LEG (T). Use two SILVER 1-1/8" FLAT
HEAD SCREWS (10S).
Step 8
425014www.sauder.com/service Page 13
E
T
Curved edge
SILVER 1-1/8" FLAT HEAD SCREW
(2 used in this step)
10S
The CAM SCREW
must be here.

å NOTE: This step shows a dierent view of the PANEL (E).
å Fasten the LEFT BOTTOM MOLDING (M) to the LEFT
REAR PEDESTAL LEG (T). Tighten one HIDDEN CAM.
å Fasten one of the LEGS (R) to the LEFT END (B) and LEFT
BOTTOM MOLDING (M). Tighten three HIDDEN CAMS.
Step 9
425014 www.sauder.com/servicePage 14
T
B
M
R
This hole
must be here.
The CAM SCREWS
must be here.
These surfaces
should be even.

å Fasten the remaining EXTENSION RAIL (35MA) to the LEFT END (B). Use
two GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3.
å NOTE: Turn a SCREW into hole #3. Then, slide the inner cartridge of the
EXTENSION RAIL in to find hole #1 that lines up with the hole in the LEFT
END. Turn a SCREW into this hole.
Step 10
425014www.sauder.com/service Page 15
B
1
2
3
GOLD 5/16" FLAT HEAD SCREW
(2 used for the RAIL)
3S
Open end

å Push four CROSS-SLOTTED DOWELS (24F) into the
BRACE (P and Q) as shown.
å NOTE: The threads in the DOWEL should be pointed
toward the hole in the edge of the BRACE.
Step 11
425014 www.sauder.com/servicePage 16
P
Q
24F
The long slot should face up
and be parallel to the long
edges of the BRACES.
24F

åFirst, fill the hole in the LEFT BOTTOM MOLDING (M) 1/4 to 1/2 full
with GLUE. Then, insert the WOOD DOWEL (15F) into this hole. Wipe
away the excess GLUE.
åNow, fill the hole in the SHORT BRACE (P) 1/4 to 1/2 full with GLUE.
åFasten the SHORT BRACE (P) to the LEFT BOTTOM MOLDING (M).
Use one BLACK 2-3/8" FLAT HEAD BOLT (103S).
åNOTE: Be sure the WOOD DOWEL in the LEFT BOTTOM MOLDING
inserts into the SHORT BRACE. Wipe away the excess GLUE.
åNOTE: The BOLT will thread into the DOWEL in the SHORT BRACE.
Step 12
425014www.sauder.com/service Page 17
M
P
Fill the holes 1/4 to 1/2 full with GLUE.
Inspect the parts thoroughly before
assembling. Disassembly of glued
parts is extremely dicult.
Caution
!
54M 15F
103S
BLACK 2-3/8" FLAT HEAD BOLT
(1 used for the SHORT BRACE)
Surface with slotted dowels

Step 13
425014 www.sauder.com/servicePage 18
P
E
K
åFirst, fill the hole in the RIGHT BACK (K) 1/4 to 1/2 full with GLUE.
Then, insert the WOOD DOWEL (15F) into this hole. Wipe away the
excess GLUE.
åNow, fill the hole in the SHORT BRACE (P) 1/4 to 1/2 full with GLUE.
åNext, fasten the RIGHT BACK (K) to the LONG MODESTY PANEL (E).
Tighten two HIDDEN CAMS.
åNOTE: Be sure the WOOD DOWEL in the RIGHT BACK (K) inserts
into the SHORT BRACE (P). Wipe away the excess GLUE.
åFasten the RIGHT BACK (K) to the SHORT BRACE (P). Use one
BLACK 2-3/8" FLAT HEAD BOLT (103S).
103S
BLACK 2-3/8" FLAT HEAD BOLT
(1 used for the SHORT BRACE)
Fill the holes 1/4 to 1/2 full with GLUE.
Inspect the parts thoroughly before
assembling. Disassembly of glued
parts is extremely dicult.
Caution
!
54M
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
Surface with
more holes

Step 14
425014www.sauder.com/service Page 19
åFirst, fill the holes in the BRACE (N) 1/4 to 1/2 full with
GLUE (54M). Then, insert the WOOD DOWELS (15F)
into the holes. Wipe away the excess GLUE.
åNow, fill the hole in the LEFT END (B) 1/4 to 1/2 full
with GLUE.
åFasten the BRACE (N) to the LEFT END (B). Tighten
one HIDDEN CAM.
åNOTE: Be sure the WOOD DOWEL in the BRACE
inserts into the LEFT END. Wipe away the excess GLUE.
Arrow
Minimum
190 degrees
Maximum
210 degrees
N
Fill the holes 1/4 to 1/2 full with GLUE.
Inspect the parts thoroughly before
assembling. Disassembly of glued
parts is extremely dicult.
Caution
!
54M
Surface with
HIDDEN CAMS
15F
Finished edge
B

å Slide the FRONT/BACK MOLDINGS* (J) onto the
notched edges of the BOTTOM (D).
å Fasten the BOTTOM (D) to the LEFT BOTTOM
MOLDING (M). Tighten two HIDDEN CAMS.
å *U.S. Patent No. 5,499,886
Step 15
425014 www.sauder.com/servicePage 20
Notched edge
The groove
is closer to
this edge.
The groove
is closer to
this edge.
Notched edge
These surfaces
should be even.
D
J
J
D
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
M