Sauder Clifford Place 429501 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
English pg 1-24
Français pg 25-28
Español pg 29-32
Lot # 557401 11/09/20
Purchased: __________________
Lateral File
Cliord Place Collection | Model 429501
Congratulations. You
are now an adult.

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
3
4
5-24
25-28
29-32
33-34
35
Page 2 www.sauder.com/service 429501

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
Page 3www.sauder.com/service429501
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D TOP MOLDING (1)
E UPPER BACK (1)
F BRACE (1)
G LOWER BACK (1)
H BOTTOM (1)
I BOTTOM MOLDING (2)
J LEFT DRAWER SIDE (2)
K DRAWER BACK (2)
L RIGHT DRAWER SIDE (2)
M DRAWER BOTTOM (2)
N DRAWER BRACE (2)
O DRAWER FRONT (2)
P FOOT (4)
A
B
C
D
E
F
G
H
I
IJ
J
K
K
L
L
M
M
N
N
O
O
P
P
P
P

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4 www.sauder.com/service 429501
ANGLED HEAD
CAM SCREW - 20
2
Angled head
LARGE HIDDEN
CAM - 20
1
WOOD
DOWEL - 18
6SHORT WOOD
DOWEL - 6
7
LONG WOOD
DOWEL - 4
5
APPLIQUE CARD - 1
19
BLACK 1-1/2" FLAT HEAD SCREW - 14
21
SILVER 5/8" FLAT HEAD SCREW - 8
23 SILVER 1/2" FLAT HEAD SCREW - 4 24
SMALL HIDDEN
CAM - 12
3STRAIGHT HEAD
CAM SCREW - 12
4
Straight head
LARGE
APPLIQUE CARD - 1
20
ADJUSTABLE
GLIDE -4
16
GROMMET
WITH CAP- 1
9
PULL - 2
8
BLACK 1-1/8" FLAT HEAD SCREW - 9
22
(EXTENSION SET SHOWN SEPARATED)
QEXTENSION RAIL - 4 REXTENSION SLIDE - 4
WASHER - 4
14
ANTI TIP KIT -2
17 HOOK - 4 18
11 SHORT FILE GLIDE - 4
12 LONG FILE GLIDE - 2 13 NOTCHED FILE GLIDE - 2
10 FILE HANGER - 4
LOCK PACK - 2
15
BLACK 1/2" PAN HEAD SCREW - 36
25 BLACK 1/2" FLAT HEAD SCREW - 4
26

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å NOTE: If you are attaching the 429505 Hutch to your unit,
build the Hutch first.
å Push twenty LARGE HIDDEN CAMS (1) into the
ENDS (A and B), BRACE (F), LOWER BACK (G),
UPPER BACK (E) and BOTTOM (H).
Page 5www.sauder.com/service429501
Arrow (20 used)
Arrow
Arrow
1
1
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
A
B
F
E
H
G
Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code. 1

Step 2
Page 6 www.sauder.com/service 429501
å Peel an applique from the LARGE APPLIQUE CARD (20)
and stick one on each large hole in the BOTTOM (H).
å Flip the BOTTOM (H) over.
å Turn and tighten four FEET (P) into the threaded holes in
the BOTTOM (H).
å Turn four ADJUSTABLE GLIDES (16) into the threaded
holes in the FEET (P).
H
20
H
P
P
P
P
16
F
l
i
p
t
h
e
B
O
T
T
O
M
o
v
e
r
Surface without
HIDDEN CAMS

Step 3
Page 7www.sauder.com/service429501
I
å Insert four SHORT WOODEN DOWELS (7) into
the BOTTOM (H).
å Fasten the BOTTOM MOLDINGS (I) to the BOTTOM (H).
Use six BLACK 1-1/8" FLAT HEAD SCREWS (22).
å NOTE: Be sure the SHORT WOODEN DOWELS insert into
the holes in the BOTTOM MOLDINGS.
77
H
I
BLACK 1-1/8" FLAT HEAD SCREW
(6 used in this step)
22

Step 4
Page 8 www.sauder.com/service 429501
Angled head
2
å Turn twenty ANGLED HEAD CAM SCREWS (2) into the
ENDS (A and B) and TOP (C).
(20 used)
A
B
C
Remember:
Righty tighty.
Lefty loosey.
1

Step 5
Page 9www.sauder.com/service429501
å Separate the EXTENSION SLIDES (R) from the EXTENSION RAILS (Q) as
shown in the enlarged diagram below. Be prepared, the parts are greasy.
å Fasten the EXTENSION RAILS (Q) to the ENDS (A and B). Use twelve
BLACK 1/2" PAN HEAD SCREWS (25).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in
the enlarged diagram. Then, slide the inner cartridge of the EXTENSION
RAIL in to find the other holes that lines up with the holes in the ENDS.
Turn a SCREW into those holes.
å NOTE: The EXTENSION SLIDES (R) will be used later for the DRAWERS.
Open end
Open end
Pull down on the black release lever and pull the SLIDE from the RAIL.
Q
Q
Q
Q
Q
QR
R
Use these holes.
A
B
BLACK 1/2" PAN HEAD SCREW
(12 used in this step)
25
7

Step 6
Page 10 www.sauder.com/service 429501
å Gather two LOCK BRACKETS from the LOCK PACK (15).
å Fasten the LOCK BRACKETS to the BRACE (F) and TOP
MOLDING (D) as shown. Use four SILVER 1/2" FLAT
HEAD SCREWS (24).
SILVER 1/2" FLAT HEAD SCREW
(4 used in this step)
24
D
F
LOCK BRACKET from LOCK
PACK (15)

Step 7
Page 11www.sauder.com/service429501
å Turn and tighten four HOOKS (18) into the BACKS (E and G).
å After the HOOKS are tight, turn them counter clockwise
a half revolution or 180 degrees. It is important that these
HOOKS are in this position for optimal performance of
the ANTI-TIP KIT.
å Insert four LONG WOOD DOWELS (5) into the
LOWER BACK (G).
å Fasten the UPPER BACK (E) to the LOWER BACK (G) by
pushing it over the WOOD DOWELS in the LOWER BACK.
5
5
18
18
E
G
Surface without
HIDDEN CAMS
Surface without
HIDDEN CAMS

Step 8
Page 12 www.sauder.com/service 429501
å Insert three WOOD DOWELS (6) into the RIGHT END (A).
å Fasten the BACKS (E and G) to the RIGHT END (A).
Tighten four HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the RIGHT END
insert into the holes in the BACKS.
å Fasten the BRACE (F) to the RIGHT END (A). Tighten the
HIDDEN CAM.
å NOTE: Be sure the WOOD DOWEL in the RIGHT END
insert into the hole in the BRACE.
E
G
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
1
2
A
F
6
6
Surface with HIDDEN CAMS
Notch
1

Step 9
Page 13www.sauder.com/service429501
å Insert two WOOD DOWELS (6) into the RIGHT END (A)
and two WOOD DOWELS (6) into the LOWER BACK (G).
å Fasten the BOTTOM (H) to the RIGHT END (A) as shown
in the upper diagram. Tighten two HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the RIGHT END
and LOWER BACK insert into the holes in the BOTTOM.
å Fasten the BOTTOM (H) to the LOWER BACK (G). Use
two BLACK 1-1/2" FLAT HEAD SCREWS (21).
6
6
H
H
A
G
G
BLACK 1-1/2" FLAT HEAD SCREW
(2 used in this step)
21
Rounded edge
1

Step 10
Page 14 www.sauder.com/service 429501
å Insert five WOOD DOWELS (6) into the LEFT END (B).
å Fasten the LEFT END (B) to the UPPER BACK (E),
BRACE (F), LOWER BACK (G) and BOTTOM (H). Tighten
seven HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the LEFT END
insert into the holes in the BACKS, BOTTOM and BRACE.
6
6
H
G
E
F
B
Surface with
HIDDEN CAMS
1

Step 11
Page 15www.sauder.com/service429501
å Insert two SHORT WOODEN DOWELS (7) into the TOP (C).
å Fasten the TOP MOLDING (D) to the TOP (C). Use three
BLACK 1-1/8" FLAT HEAD SCREWS (22).
å NOTE: Be sure the SHORT WOOD DOWELS in the TOP
insert into the holes in the TOP MOLDING.
BLACK 1-1/8" FLAT HEAD SCREW
(3 used in this step)
22
7
Rounded edge
Now might be a
good time to refresh
your drink.
C D

Step 12
Page 16 www.sauder.com/service 429501
å Turn twelve STRAIGHT HEAD CAM SCREWS (4) into the
DRAWER FRONTS (O).
å Push twelve SMALL HIDDEN CAMS (3) into the
large holes in the DRAWER SIDES (J and L) and
DRAWER BRACE (N). Straight head
4
(12 used)
OO
J
J
N
N
L
L
3
Arrow
(12 used)
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
1

Step 13
Page 17www.sauder.com/service429501
å Fasten a DRAWER BACK (K) to the DRAWER SIDES (J and L) and DRAWER BRACE (N). Use six BLACK 1-1/2" FLAT
HEAD SCREWS (21).
å NOTE: Be sure the DRAWER BOTTOM (M) inserts into the groove of the DRAWER BACK (K).
å Repeat this step for the other drawer.
å Fasten a LEFT DRAWER SIDE (J), a RIGHT DRAWER
SIDE (L) and a DRAWER BRACE (N) to a DRAWER
FRONT (O). Tighten six SMALL HIDDEN CAMS.
å Slide a DRAWER BOTTOM (M) into the grooves
in the DRAWER SIDES (J and L) and DRAWER FRONT (O).
Groove
Be sure the
DRAWER
BOTTOM inserts
into the DRAWER
BACK groove.
BLACK 1-1/2" FLAT HEAD SCREW
(12 used in this step)
21
J
J
J
L
L
L
N
N
K
M
M
1 2
3
O
O
Unfinished surface
Surface with HIDDEN CAMS
1

Step 14
Page 18 www.sauder.com/service 429501
å Fasten the EXTENSION SLIDES (R) to the DRAWER
SIDES (J and L). Use six BLACK 1/2" PAN HEAD SCREWS (25).
å Repeat this step for the other drawer.
J
L
R
R
Open end
Open end
BLACK 1/2" PAN HEAD SCREW
(12 used in this step)
25
Use these holes.
R
Open end

Step 15
Page 19www.sauder.com/service429501
SILVER 5/8" FLAT HEAD SCREW
(8 used for the LOCKS)
23
å Fasten a Lock from the LOCK PACK (15) to a DRAWER
FRONT (O). Use four SILVER 5/8" FLAT HEAD SCREWS (23).
å Fasten a PULL (8) to the DRAWER FRONT (O). Use two
BLACK 1/2" FLAT HEAD SCREWS (26).
å Fasten the NOTCHED FILE GLIDE (13) to the DRAWER
FRONT (O). Use six BLACK 1/2" PAN HEAD SCREWS (25).
å Repeat this step for the other drawer.
BLACK 1/2" PAN HEAD SCREW
(12 used for the NOTCHED FILE GLIDES)
25
BLACK 1/2" FLAT HEAD SCREW
(4 used for PULLS)
26
O
8
15
13
The tab on the Lock
should be on top.

Step 16
Page 20 www.sauder.com/service 429501
å Push two SHORT FILE GLIDES (11) onto the top edges of
the DRAWER SIDES (J and L).
å Push the LONG FILE GLIDE (12) onto the top edge of the
DRAWER BACK (K).
å Push two FILE HANGERS (10) onto the NOTCHED FILE
GLIDE (13) and LONG FILE GLIDE (12).
å Push a LOCK RING onto the LOCK as shown.
å Repeat this step for the other drawer.
J
K
L
O
11
12
10
10
11
13
If you're doing this to
help a friend, don't
leave without a bite.
Lock Ring from the LOCK PACK (15)