Sauder 425024 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Enlish p 1-23
Français p 24-27
Español p 28-31
Dresser
WARNING
CHOKING HAZARD - Small Parts
Not for children under 3 years.
Adult assembly required.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
2-3
4-5
6-23
24-27
28-31
32-34
35
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Part Identification
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
D TOP (1)
D30 RIGHT DRAWER SIDE (6)
D31 LEFT DRAWER SIDE (6) - 1 with label
D80 DRAWER BACK (6)
D985 DRAWER BOTTOM (6)
E BOTTOM (1)
F BACK (1)
G SKIRT (2)
H LEFT DRAWER FRONT (3)
I RIGHT DRAWER FRONT (3)
J DRAWER FRONT MOLDING (12)
L FOOT (6)
M67
DRAWER BRACE (6)
(Hidden part usin recycled
material. Color may vary.)
Pae 2

Now you know
our ABCs.
Part Identification
A
B
C
D
E
F
G
H
I
J
L
D985
D80
D30
D31
G
L
L
L
J
J
J
D985
D30
D31
D80
L
L
M67
M67
Pae 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
ANGLE BRACKET - 6
5G
10A SLIDE CAM - 12
NAIL - 57
1N
HIDDEN CAM - 16
1F CAM DOWEL - 16 2F PULL - 6
182K
FURNITURE TIPPING
RESTRAINT KIT - 1
97
35AA UNIVERSAL CABINET RAIL - 12 35AC DRAWER RIGHT - 6 35AD DRAWER LEFT - 6
Pae 4

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 9/16" LARGE HEAD SCREW - 12
1S
BLACK 1-1/4" FLAT HEAD SCREW - 24
7S BLACK 2-1/4" FLAT HEAD SCREW - 2 26S
BLACK 7/8" MACHINE SCREW - 12
37S
BLACK 2-3/8" FLAT HEAD BOLT - 6
103S
30S BLACK 1-9/16" FLAT HEAD SCREW - 30
3S GOLD 5/16" FLAT HEAD SCREW - 48
Pae 5

HOW TO USE A HIDDEN CAM & CAM DOWEL 2. Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
1. Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the edge
of the board.
Hole
Arrow
Metal end
Hidden Cam
Cam Dowel
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
3.
Hardware Usae Guide
1
Step 1 Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Push two HIDDEN CAMS (1F) into the LEFT END (B).
Then, insert the metal end of a CAM DOWEL (2F) into
each HIDDEN CAM.
Do not tihten the HIDDEN CAMS in this step.
B
Arrow
1F
2F
Metal end
Pae 6

å Fasten three UNIVERSAL CABINET RAILS* (35AA) to the
LEFT END (B). Use six GOLD 5/16" FLAT HEAD SCREWS (3S)
throuh holes #1 and #3.
å *patent pendin lide system
Step 2
B
Glide end
3
3
3
2
2
2
1
1
1
Surface with
HIDDEN CAMS
Rounded ede
GOLD 5/16" FLAT HEAD SCREW
(6 used in this step)
3S
Just think. The sooner
you do this, the sooner
you do somethin else.
Pae 7

Step 3
å Open the FURNITURE TIPPING RESTRAINT KIT (97) and
fasten the SAFETY STRAP to the TOP (D). Use the short
screw provided.
å NOTE: Position the SAFETY STRAP exactly as shown.
å Fasten the LEFT END (B) to the TOP (D). Tihten two
HIDDEN CAMS.
B
D
D
Safety strap
97
Surface
with
HIDDEN
CAMS
Surface with holes
Surface with holes
This strap must be here.
Rounded ede
Meet Part (D). This component has
been enineered to be lihter, stroner,
faster… well ok. Not technically faster.
But definitely makes for a sturdier
dresser that’s easier to assemble and
friendlier to the environment.
Pae 8
Do not stand the unit upriht without the
BACK fastened. The unit may collapse.
Caution

Step 4
å Push two HIDDEN CAMS (1F) into the UPRIGHT (C). Then,
insert the metal end of a CAM DOWEL (2F) into each
HIDDEN CAM.
C
Do not tihten the HIDDEN CAMS in this step.
Arrow
1F
2F
Metal end
Pae 9

Step 5
å Fasten six UNIVERSAL CABINET RAILS* (35AA) to
the UPRIGHT (C). Use twelve GOLD 5/16" FLAT HEAD
SCREWS (3S) throuh holes #1 and #3.
å *patent pendin lide system
C
C
Glide end
3
2
1
3
2
1
3
2
1
GOLD 5/16" FLAT HEAD SCREW
(12 used in this step)
3S Glide end
3
2
1
3
2
13
2
1
F
L
I
P
O
V
E
R
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
Pae 10