Sauder Adept Storage 418141 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-32
Français pg 33-36
Español pg 37-40
Lot # 366939 11/20/15
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Storage Cabinet
Adept Storage Collection | 418141
Store behind
closed doors.

Table of Contents Assembly Tools Required
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4
5-32
33-36
37-40
41-42
43
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
418141 www.sauder.com/servicesPage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
D HINGE UPRIGHT (2)
E TOP (1)
F BOTTOM (1)
G BACK (1)
H DOOR (2)
I ADJUSTABLE SHELF (6)
J RIGHT LEG (1)
K LEFT LEG (1)
L BASE (1)
M TOP MOLDING (1)
N DOOR MOLDING (4)
O CENTER MOLDING (1)
A
BCD
D
E
F
I
I
I
I
I
I
J
K
L
M
N
NN
N
O
HH
G
418141www.sauder.com/services Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
SMALL HIDDEN
CAM - 8
29F
SAFETY BRACKET - 1
1G TIE PLATE/
DOOR STOP - 4
3G
BLACK 9/16" LARGE HEAD SCREW - 21
1S BLACK 1-7/8" FLAT HEAD SCREW - 9 2S
CAM COVER - 24
13P METAL PIN - 24 1R
SILVER 5/8" FLAT HEAD SCREW - 12
23S
22H
HINGE SPACER - 6
CAM SCREW - 28
8F
NAIL - 66
1N
HIDDEN CAM - 28
1F CAM DOWEL - 8 2F
SILVER 3/8" MACHINE SCREW - 4
97S
LARGE RUBBER
SLEEVE - 2
59G
RUBBER SLEEVE - 24
2R
14H HINGE - 6 PULL - 2 53K
418141 www.sauder.com/servicesPage 4
WOOD DOWEL - 8
26F
GLUE - 1
54M
METAL BRACKET - 7
4G

å You have the option to build your unit with one door opening to the left
and one door opening to the right, both doors opening to the right, or
both doors opening to the left as shown below. After you have chosen
one option, follow the steps listed below the diagram.
418141www.sauder.com/services Page 5
STEPS 1-15, 24-27
DOORS OPEN LEFT/RIGHT DOORS OPEN LEFT
STEPS 1-11, 20-23, 24-27
DOORS OPEN RIGHT
STEPS 1-11, 16-19, 24-27
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1349
to watch a video on how to assemble
your unit.
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1350
to watch a video on how to assemble
your unit.
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1351
to watch a video on how to assemble
your unit.

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push eight SMALL HIDDEN CAMS (29F) into the holes in
the DOORS (H).
å NOTE: Be sure the arrow in the CAM is pointing toward
the hole in the short edge of the DOORS.
Arrow
Arrow
H
H
(8 used)
418141 www.sauder.com/servicesPage 6
29F
hole

StepStep 2
N
8F
å First, fill the two outside holes in a DOOR MOLDING (N)
1/4 to 1/2 full with GLUE (54M). Then, insert two WOOD
DOWELS (26F) into the holes. Wipe away the excess GLUE.
å Turn two CAM SCREWS (8F) into the DOOR MOLDING (N).
å Repeat this step for the remaining DOOR MOLDINGS.
(8 used)
418141www.sauder.com/services Page 7
Remember:
Righty tighty.
Lefty loosey.
54M
26F
(8 used)

Step
å 1. Fill two outside holes in one of the DOORS (H) 1/4 to 1/2 full
with GLUE (54M). Fasten a DOOR MOLDING (N) to the end
of the DOOR (H) which you dropped glue into. Tighten two
HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS insert into the holes. Wipe
away the excess GLUE.
å NOTE: Be sure all angled edges on the DOOR MOLDINGS (N)
are facing the floor as shown in the enlarged diagram.
å 2-4. Repeat this step gluing and fastening the remaining DOOR
MOLDINGS (N) to the DOORS (H).
Step 3
H
H
N
N
N
N
Angled edge
418141 www.sauder.com/servicesPage 8
54M
1st
2nd
3rd
4th
1
2

Step
å Place the HINGE SPACERS (22H) over the large holes in
the DOORS (H).
å Fasten the HINGES (14H) to the DOORS (H). Use twelve
SILVER 5/8" FLAT HEAD SCREWS (23S).
Step 4
H
H
SILVER 5/8" FLAT HEAD SCREW
(12 used in this step)
23S
14H
14H
22H
22H
418141www.sauder.com/services Page 9

Step
A
B
Step 5
Arrow
1F
2F
å Push twenty HIDDEN CAMS (1F) into the ENDS (A and B), UPRIGHT (C), TOP (E), and BOTTOM (F). Then, insert the metal
end of a CAM DOWEL (2F) into each HIDDEN CAM except in the ENDS (A and B) and UPRIGHT (C).
(20 used)
(8 used)
Arrow
1F
2F
Arrow
1F
Do not tighten the HIDDEN CAMS in this step.
Do not insert CAM DOWELS into these parts.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
E
F
C
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
418141 www.sauder.com/servicesPage 10

Step
A
B
Step 6
E
F
å Fasten seven METAL BRACKETS (4G) to the ENDS (A
and B), TOP (E) and BOTTOM (F). Use seven BLACK
9/16" LARGE HEAD SCREWS (1S).
å NOTE: Be sure the BRACKETS are even with the long
edges of ENDS, TOP, and BOTTOM.
BLACK 9/16" LARGE HEAD SCREW
(7 used for the METAL BRACKETS)
1S
418141www.sauder.com/services Page 11
4G
4G
4G

Step
å Fasten the TOP (E) AND BOTTOM (F) to the RIGHT END (A).
Tighten four HIDDEN CAMS.
å NOTE: The METAL BRACKETS should be on the floor.
Step 7
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
A
E
F
Surface with HIDDEN CAMS
Surface with HIDDEN CAMS
Surface with HIDDEN CAMS
418141 www.sauder.com/servicesPage 12
Edge with METAL BRACKETS
Edge with METAL BRACKETS
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

Step
å Fasten the UPRIGHT (C) to the TOP (E) and BOTTOM (F).
Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S).
Step 8
E
F
Surface with HIDDEN CAMS
C
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
2S
The CAMS should be
close to the floor.
418141www.sauder.com/services Page 13

Step
å Fasten the LEFT END (B) to TOP (E) and BOTTOM (F).
Tighten four HIDDEN CAMS.
Step 9
Arrow
Minimum
190 degrees
Maximum
210 degrees
E
F
B
Curved edge
418141 www.sauder.com/servicesPage 14
Surface without
HIDDEN CAMS

Step
å Fasten the TOP MOLDING (M) to the TOP (E) and ENDS (A
and B). Use four BLACK 9/16" LARGE HEAD SCREWS (1S).
å Fasten two TIE PLATES/DOOR STOPS (3G) to the BASE (L).
Use two BLACK 9/16" LARGE HEAD SCREWS (1S).
å Fasten the BASE (L) to the BOTTOM (F). Use three BLACK
9/16" LARGE HEAD SCREWS (1S). Do not completely tighten
these screws at this time.
Step 10
E
F
B
A
3G
M
L
418141www.sauder.com/services Page 15
BLACK 9/16" LARGE HEAD SCREW
(9 used in this step)
1S

StepStep 11
å Unfold the BACK (G) and lay it over your unit.
å Make equal margins along all four edges of the BACK (G).
Push on opposite corners of your unit if needed to make
it "square".
å Fasten the BACK (G) to your unit using the NAILS (1N).
å NOTE: Be sure to tap NAILS into the holes that line up
over the UPRIGHT (C).
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
Unfinished
surface
These holes must line up
over the UPRIGHT (C).
NAIL
(66 used in this step)
1N
G
418141 www.sauder.com/servicesPage 16
Now might be a
good time to refresh
your drink.

Step
å Fasten two TIE PLATES/DOOR STOPS (3G) to the
CENTER MOLDNG (O). Use two BLACK 9/16" LARGE
HEAD SCREWS (1S).
å Push two LARGE RUBBER SLEEVES (59G) over the ends
of the TIE PLATES/DOOR STOPS (3G).
å Turn twenty CAM SCREWS (8F) into the LEGS (J and K)
and CENTER MOLDING (O).
Step 12
J
K
BLACK 9/16" LARGE HEAD SCREW
(2 used in this step)
1S
3G
59G
59G
3G
8F
(20 used)
Use the center holes only
for the CAM SCREWS.
Use the small holes for
the DOOR STOPS (3G).
O
DOORS OPEN LEFT/RIGHT
418141www.sauder.com/services Page 17

Step
å Flip your unit onto its BACK. Fasten the RIGHT LEG (J)
to the RIGHT END (A) and the LEFT LEG (K) to the LEFT
END (B). Tighten eight HIDDEN CAMS.
å Fasten the CENTER MOLDING (O) to the UPRIGHT (C).
Tighten four HIDDEN CAMS.
å Fasten the BASE (L) to the LEGS (J and K). Turn two
BLACK 9/16" LARGE HEAD SCREWS (1S) through the
DOOR STOP/TIE PLATES (3G).
å Tighten the screws that hold the BASE (L) to the METAL
BRACKETS on the BOTTOM (F).
Step 13
1
2
Be sure the top surface of
the BASE and BOTTOM
are even. Tighten three
SCREWS in the BASE.
The DOOR
STOPS with
the RUBBER
SLEEVES
must be here. J
A
K
B
C
O
DOORS OPEN LEFT/RIGHT
BLACK 9/16" LARGE HEAD SCREW
(2 used for the TIE PLATES)
1S
L
F
3G
3G
418141 www.sauder.com/servicesPage 18

Step
å NOTE: The HINGE UPRIGHTS (D) have locator holes near the
top edges as shown.
å Push four HIDDEN CAMS (1F) into the surface with the locator
hole and push four HIDDEN CAMS (1F) into the opposite
surface of the locator hole in the HINGE UPRIGHTS (D).
å NOTE: The HINGE UPRIGHTS (D) are now called LEFT HINGE
UPRIGHT (D) and RIGHT HINGE UPRIGHT (D).
Step 14
Locator hole
D
D
Arrow
Hole Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
RIGHT HINGE
UPRIGHT (D)
LEFT HINGE
UPRIGHT (D)
DOORS OPEN LEFT/RIGHT
418141www.sauder.com/services Page 19
Arrow
1F
Arrow
1F
(8 used)
Hole

Step
å Fasten the RIGHT HINGE UPRIGHT (D) to the RIGHT LEG (J) and
fasten the LEFT HINGE UPRIGHT (D) to the LEFT LEG (K). Tighten
eight HIDDEN CAMS.
å NOTE: The locator holes in the HINGE UPRIGHTS (D) are near the
TOP MOLDING (M).
å Fasten the HINGE UPRIGHTS (D) to the TOP (E) and BOTTOM (F).
Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S).
Step 15
LEFT HINGE
UPRIGHT (D)
Locator hole
RIGHT HINGE
UPRIGHT (D)
M
J
K
DOORS OPEN LEFT/RIGHT
418141 www.sauder.com/servicesPage 20
E
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
2S
2S
2S
F
Locator hole
D
D