Sauder Primary Street 417932 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-15
Français pg 16-18
Español pg 19-21
Lot # 369831 03/03/15
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Play Table
Primary Street Collection | 417932
WARNING
CHOKING HAZARD - Small Parts
Not for children under 3 years.
Adult assembly required.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
3
4
5-15
16-18
19-21
22
23
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
417932 www.sauder.com/servicesPage 2
Short Screwdriver

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A UPRIGHT (1)
B TOP (1)
C BOTTOM (1)
D SHELF (2)
E BACK (1)
F DIVIDER (2)
G FRONT (1)
H FRONT BASE (1)
I SIDE BASE (2)
J SKIRT (2)
K BLUE PANEL (1)
L RED PANEL (1)
M GREEN PANEL (1)
N YELLOW PANEL (1)
O BLUE MAT (1)
P GREEN MAT (1)
A
B
C
D
E
F
G
H
I
J
D
F
J
I
K L
OR
O P
OR
O P
OR
M N
OR
M N
OR
417932www.sauder.com/services Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
PLASTIC FOOT - 1
20E
31G CORNER BRACKET - 4
METAL BRACKET - 4
4G
GOLD 1" MACHINE SCREW - 20
50S
BLACK 9/16" LARGE HEAD SCREW - 32
1S
BLACK 1-7/8" FLAT HEAD SCREW - 10
2S
METAL PIN - 8
1R
HIDDEN CAM - 28
1F CAM DOWEL - 28 2F
417932 www.sauder.com/servicesPage 4
WASHER - 20
77M

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty carton
to avoid scratching your unit or the floor.
å Push twenty eight HIDDEN CAMS (1F) into the UPRIGHT (A),
TOP (B), BOTTOM (C), SHELVES (D), and DIVIDERS (F).
Then, insert the metal end of a CAM DOWEL (2F) into each
HIDDEN CAM.
417932www.sauder.com/services Page 5
A
B
C
D
D
F
F
(28 used)
(28 used)
Arrow
1F
2F
Do not tighten the HIDDEN CAMS in this step.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow

å Fasten four PANELS (K, L, M, and N) to the FRONT (G).
Use twenty GOLD 1" MACHINE SCREWS (50S) through
twenty WASHERS (77M), through the FRONT (G), and into
the PANELS (K, L, M, and N).
Step 2
417932 www.sauder.com/servicesPage 6
G
M N
OR
GOLD 1" MACHINE SCREW
(20 used in this step)
50S
Rounded edge
Surface with fewer holes
77M
(20 used)
M N
OR
K L
OR
K L
OR

å Fasten the UPRIGHT (A) and SKIRTS (J) to the TOP (B).
Tighten six HIDDEN CAMS.
Step 3
417932www.sauder.com/services Page 7
B
J
J
A
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
Edge with no holes
Surface
with holes
Surface with
HIDDEN CAMS
Rounded
edge
Rounded
edge
The SKIRTS (J) should overhang
this surface of the TOP (B).

Step 4
417932 www.sauder.com/servicesPage 8
å Insert two METAL PINS (1R) into the corner holes in the
BACK (E).
å Fasten the UPRIGHT (A) and TOP (B) to the BACK (E).
Tighten six HIDDEN CAMS.
å NOTE: Be sure the METAL PINS (1R) in the BACK (E)
insert into the holes in the SKIRTS (J).
å Now, insert two METAL PINS (1R) into the other end of
the SKIRTS (J).
B
J
A
E
Surface
with holes
1R
1R
J
Arrow
Minimum
190 degrees
Maximum
210 degrees
Rounded edge

å Fasten the DIVIDERS (F) to the TOP (B). Tighten four
HIDDEN CAMS.
Step 5
417932www.sauder.com/services Page 9
B
F
F
Arrow
Minimum
190 degrees
Maximum
210 degrees
Finished edge
Finished edge
Surface with HIDDEN CAMS Surface without HIDDEN CAMS

Step 6
417932 www.sauder.com/servicesPage 10
E
D
Surface with
HIDDEN CAMS
D
Surface with
HIDDEN CAMS
F
F
1R
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
2S
Finished edge
Finished edge
å Insert two METAL PINS (1R) into the BACK (E).
å Fasten the SHELVES (D) to the BACK (E). Tighten two
HIDDEN CAMS.
å NOTE: Be sure the METAL PINS (1R) in the BACK (E)
insert into the holes in the SHELVES (D).
å Insert two METAL PINS (1R) into the other end of
the SHELVES (D).
å Fasten the SHELVES (D) to the DIVIDERS (F). Use four
BLACK 1-7/8" FLAT HEAD SCREWS (2S).
Arrow
Minimum
190 degrees
Maximum
210 degrees
1R