Sauder Briarbrook 430077 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
English pg 1-36
Français pg 37-40
Español pg 41-44
Lot # 573697 11/02/21
Purchased: __________________
Hutch
Briarbrook Collection | Model 430077
For things 'n such.

Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
3
4
5
6-36
37-40
41-44
45-46
47
Electric drill with 1/8" or 3/8" bit
(ONLY in indicated step)
Pencil
Page 2 www.sauder.com/service 430077

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A TOP (1)
B LEFT END (1)
C RIGHT END (1)
D LEFT UPRIGHT (1)
E RIGHT UPRIGHT (1)
F BOTTOM (1)
G SHELF (2)
H LEFT DOOR (1)
J RIGHT DOOR (1)
K MOLDING (2)
L SMALL BACK (1)
M BRACKET (2)
N LARGE BACK (2)
O LEFT FRAME (1)
P RIGHT FRAME (1)
A
B
C
D
E
F
G
H
J
K
L
M
N
O
P
N
G
K
M
Page 3www.sauder.com/service430077

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
SHELF PIN - 8
1HINGE - 4
2CAM SCREW - 12
3HIDDEN CAM - 12 4
WOOD DOWEL - 8
5L-WRENCH - 1
67MAGNETIC
CATCH - 1 PAD CARD - 1
8
NUT - 4
9APPLIQUE CARD - 1
10 PULL - 2 11 WRENCH - 1
12
FURNITURE TIPPING
RESTRAINT KIT - 1
96
1-9/16" PAN HEAD SCREW - 4
13 1/2" PAN HEAD SCREW - 16 14 1/2" HEX HEAD SCREW - 24 15
3/8" HEX HEAD SCREW - 4
17 1/2" FLAT HEAD SCREW - 2
18
9/16" FLAT HEAD SCREW - 24
16
5/8" FLAT HEAD SCREW - 2
20
Page 4 www.sauder.com/service 430077
1-9/16" HEX HEAD SCREW - 6
19

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Page 5www.sauder.com/service430077

Step 1 Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push eight HIDDEN CAMS (4) into the UPRIGHTS (D and E),
and BOTTOM (F).
1
D
E
F
4
Arrow
Arrow
4
Page 6 www.sauder.com/service 430077
Some assembly
(and snacks) required.

å Insert two WOOD DOWELS (5) into the BOTTOM (F).
å Fasten the UPRIGHTS (D and E) to the BOTTOM (F). Use
four 1-9/16" PAN HEAD SCREWS (13).
å NOTE: Be sure the WOOD DOWELS in the BOTTOM
insert into the UPRIGHTS.
Step 2
F
D
E
5
5
1-9/16" PAN HEAD SCREW
(4 used in this step)
13
Surface without
HIDDEN CAMS
Surface with
HIDDEN CAMS
Page 7www.sauder.com/service430077

å Push four HIDDEN CAMS (4) into the ENDS (B and C).
å Turn four CAM SCREWS (3) into the ENDS (B and C).
Step 3 1
B
C
Arrow
4
4
Arrow
3
3
Page 8 www.sauder.com/service 430077

Step 4
å Insert two WOOD DOWELS (5) into the ENDS (B and C).
å Fasten the ENDS (B and C) to the BOTTOM (F). Tighten
four HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the ENDS insert
into the BOTTOM.
1
F
B
C
5
5
Surface without
HIDDEN CAMS
Surface with
HIDDEN CAMS
Page 9www.sauder.com/service430077

å Turn eight CAM SCREWS (3) into the TOP (A).
Step 5 1
Page 10 www.sauder.com/service 430077
A
3
3
Meet Part (A). This component has
been engineered to be lighter, stronger,
faster… well ok. Not technically faster.
But definitely makes for a sturdier
Hutch that’s easier to assemble and
friendlier to the environment.

å Fasten the large piece of the MAGNETIC CATCH (7) to
the TOP (A). Use two 5/8" FLAT HEAD SCREWS (20).
å NOTE: The other parts of the MAGNETIC CATCH will be
used in a later step.
Step 6
A
7
5/8" FLAT HEAD SCREW
(2 used in this step)
20
Page 11www.sauder.com/service430077

Step 7
å Carefully stand your unit upright.
å Insert four WOOD DOWELS (5) into the TOP (A).
å Fasten the TOP (A) to the ENDS (B and C) and UPRIGHTS (D and E).
Tighten eight HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the TOP insert into the ENDS
and UPRIGHTS.
1
A
B
C
D
E
5
(4 used)
MAGNETIC CATCH
should be near this edge.
Page 12 www.sauder.com/service 430077

Step 8
å Fasten the HINGES (2) to the DOORS (H and J). Use eight 9/16"
FLAT HEAD SCREWS (16).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
å Fasten the remaining MAGNETIC CATCH (7) parts to the
DOORS (H and J). Use two 1/2" FLAT HEAD SCREWS (18).
H
J
2
9/16" FLAT HEAD SCREW
(8 used in this step)
16
7
7
1/2" FLAT HEAD SCREW
(2 used in this step)
18
Page 13www.sauder.com/service430077

å Before fastening the DOORS to your unit, be sure the
mounting screw is against the stops as shown in the
right diagram. If it isn't, loosen the adjusting screw and
mounting screw to slide it against the stops. Then tighten
the mounting screw.
å Fasten the LEFT DOOR (H) to the LEFT UPRIGHT (D)
and the RIGHT DOOR (J) to the RIGHT UPRIGHT (E)
as shown in the lower diagram. Use sixteen 9/16" FLAT
HEAD SCREWS (16).
å See a later step for DOOR adjustments.
Step 9 17
D
E
H
J
9/16" FLAT HEAD SCREW
(16 used in this step)
16
Page 14 www.sauder.com/service 430077
Stop
Mounting
screw
Adjusting
screw
Hinge

Step 10
å Turn your unit onto its back edges.
å Fasten the MOLDINGS (K) to the BOTTOM (F). Tighten six
1-9/16" HEX HEAD SCREWS (19) using the L-WRENCH (6).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
F
K
K
6
1-9/16" HEX HEAD SCREW
(6 used in this step)
Page 15www.sauder.com/service430077
19

å Fasten the SMALL BACK (L) to the FRAMES (O and P). Turn four 1/2"
HEX HEAD SCREWS (15) a few turns using the L-WRENCH (6). Do not
completely tighten the SCREWS at this time.
å Fasten the FRAMES (O and P) to the ENDS (B and C). Turn twelve 1/2"
HEX HEAD SCREWS (15) a few turns using the L-WRENCH (6). Do not
completely tighten the SCREWS at this time.
å Fasten the FRAMES (O and P) to the TOP (A). Turn four 1/2" HEX
HEAD SCREWS (15) a few turns using the L-WRENCH (6).
å Now, completely tighten all of the SCREWS in this step.
å Peel the PADS from the PAD CARD (8) and apply them to the bottom
of the FRAMES (O and P) as shown.
Step 11
Page 16 www.sauder.com/service 430077
B
C
L
O
P
6
A
K
K
1/2" HEX HEAD SCREW
(20 used in this step)
15
8
8

Step 12
å Carefully turn your unit onto its front edges.
å Fasten the LARGE BACKS (N) to the TOP (A) and BOTTOM (F). Use twelve 1/2" PAN HEAD SCREWS (14).
å NOTE: You should start each SCREW a few turns before completely tightening any of them.
A
F
N
N
1/2" PAN HEAD SCREW
(12 used in this step)
14
Page 17www.sauder.com/service430077

å Carefully stand your unit upright.
å Insert the SHELF PINS (1) into the hole locations of your choice in the
ENDS (B and C) and UPRIGHTS (D and E). Set the notched edges of
the SHELF (G) onto the SHELF PINS.
å Fasten the PULLS (11) to the DOORS (H and J). Use four 1/2" PAN
HEAD SCREWS (14).
å Open the FURNITURE TIPPING RESTRAINT KIT (96), and fasten the
SAFETY STRAP to the TOP (A). Use the provided SHORT SCREW.
Step 13
Page 18 www.sauder.com/service 430077
Now might be a
good time to refresh
your drink.
B
C
D
E
G
G
H
J
1(8 used)
1/2" PAN HEAD SCREW
(4 used in this step)
14
11
11
96 Use the SHORT SCREW
from the RESTRAINT KIT.
A
SAFETY STRAP

å Refer to the enlarged diagram to identify the parts on
the HINGES.
å The DOORS may need some adjustments. Follow the text below to make needed adjustments.
å DOOR ADJUSTMENTS:
To adjust the DOORS from side to side (horizontal), turn the adjusting screw in or out.
å To adjust the DOORS in or out (depth), loosen the mounting screw one turn and move the DOORS in or out, as needed.
Tighten the mounting screw after making adjustments.
Step 14
Page 19www.sauder.com/service430077
17
Adjusting screw (horizontal)
Mounting screw (depth)

Step 15
å You have the option to have the Hutch on the 430074 credenza, 430071 desk and return, 430071 desk,
or 429446 desk.
å If you want the Hutch on the 430074 credenza go to Step 16.
å If you want the Hutch on the 430071 desk and return go to Step 20.
å If you want the Hutch on the 430071 desk go to Step 24.
å If you want the Hutch on the 429446 desk go to Step 28.
Page 20 www.sauder.com/service 430077
Hutch on 430074
Steps 16 - 19
Hutch on 430071 desk and return
Steps 20 - 23
Hutch on 430071 desk
Steps 24 - 27
430074
Credenza
Hutch on 429446
Steps 28 - 31
430071
Return 430071
Desk
430071
Desk
429446
Desk
Credenza
Desk