Sauder Shoal Creek 411222 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-20
Français pg 21-23
Español pg 24-26
Lot # 563709 04/09/21
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Mates Bed
Shoal Creek Collection | Model 411222
You won't just fall in
love with it. You'll fall
asleep in it.

Table of Contents Assembly Tools Required
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Warranty
2-3
4
5-20
21-23
24-26
27
411222 www.sauder.com/servicesPage 2
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A2 BOTTOM (2)
B3 BOTTOM SUPPORT (2)
B30 DRAWER BOTTOM (2)
C3 UPRIGHT (1)
D212 RIGHT DRAWER SIDE (2)
D213 LEFT DRAWER SIDE (2)
D476 DRAWER BACK (2)
D477 DRAWER DIVIDER (2)
EE2 END (2)
G3 UPPER FRONT PANEL (1)
H3 LOWER FRONT PANEL (1)
I3 BACK PANEL (1)
J2 SMALL SLAT (4)
M65
DRAWER BRACE (2)
(Hidden part using recycled
material. Color may vary.)
S RIGHT DRAWER FRONT (1)
T LEFT DRAWER FRONT (1)

Part Identification
411222www.sauder.com/services Page 3
A2
A2
B3
B3
C3
G3
B30
B30
S
T
H3
D476 D477
D477
D476
EE2
EE2
I3
D212
D212
D213
D213
J2
J2 J2
J2
M65
M65
Now you know
our ABCs.

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
411222 www.sauder.com/servicesPage 4
40CB CABINET LEFT - 2 40CA CABINET RIGHT - 2 40CC DRAWER RIGHT - 2 40CD DRAWER LEFT - 2
30S BLACK 1-9/16" FLAT HEAD SCREW - 10
SILVER 1-1/8" FLAT HEAD SCREW - 20
10S 15S SILVER 5/8" MACHINE SCREW - 8
BLACK 9/16" LARGE HEAD SCREW - 10
1S 3S GOLD 5/16" FLAT HEAD SCREW - 16
SUPPORT BRACKET - 1
11B WOOD DOWEL - 11 15F
HIDDEN CAM -14
1F CAM DOWEL - 14 2F
SUPPORT PIN - 12
4R
PULL- 4
31K
DRAWER FRONT BRACKET - 2
8G GLUE - 1
177M
SILVER 1-5/8" FLAT HEAD SCREW - 10
152S

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push fourteen HIDDEN CAMS (1F) into the UPRIGHT (C3),
DRAWER BRACES (M65), and PANELS (G3, H3, and I3).
Then, insert the metal end of a CAM DOWEL (2F) into
each HIDDEN CAM.
411222www.sauder.com/services Page 5
(14 used)
Arrow
1F
2F Do not tighten the HIDDEN CAMS in this step.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
I3
G3
C3
H3
M65
M65

å Fasten a CABINET RIGHT (40CA) and a CABINET
LEFT (40CB) to the ENDS (EE2). Use four GOLD 5/16"
FLAT HEAD SCREWS (3S) through holes #1 and #3.
å NOTE: After you attach the CABINET RAILS, the ENDS
will be labeled RIGHT END and LEFT END.
Step 2
411222 www.sauder.com/servicesPage 6
EE2
EE2
Remember:
Righty tighty.
Lefty loosey.
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
Roller end
Roller end
1
2
34
1
2
3
4
This END (EE2) will now be
called the RIGHT END (EE2).
This END (EE2) will now be
called the LEFT END (EE2).
Rounded edge
Rounded edge

å Fasten the remaining CABINET RIGHT (40CA) and
CABINET LEFT (40CB) to the UPRIGHT (C3). Use
four GOLD 5/16" FLAT HEAD SCREWS (3S) through
holes #1 and #3.
Step 3
411222www.sauder.com/services Page 7
C3
Surface with
HIDDEN CAMS
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
Roller end
Roller end
1
2
3
4
1
2
3
4
Finished edge

Step 4
411222 www.sauder.com/servicesPage 8
å Fasten the BOTTOM SUPPORTS (B3) to the ENDS (EE2).
Use eight SILVER 1-1/8" FLAT HEAD SCREWS (10S).
å Fasten the SMALL SLATS (J2) to the BACK PANEL (I3)
and UPPER FRONT PANEL (G3). Use twelve SILVER 1-1/8"
FLAT HEAD SCREWS (10S).
å NOTE: Use the exact holes shown.
Left End Right End
B3
B3
EE2
EE2
I3
G3
SILVER 1-1/8" FLAT HEAD SCREW
(20 used in this step)
10S
Edge without holes
If the BOTTOM SUPPORTS (B3) or
SMALL SLATS (J2) have a finished
surface, it should be facing up.
J2
J2
J2
J2
Edge without holes
Edge without holes
Finished edge
Finished edge

å First, fill the holes in a short edge of the BACK PANEL (I3) 1/4 to
1/2 full with GLUE (177M). Then, insert two WOOD DOWELS (15F)
into the holes. Wipe away the excess GLUE.
å Next, fill the holes in the other short edge of the BACK PANEL (I3)
1/4 to 1/2 full with GLUE. Then, insert two WOOD DOWELS (15F)
into these holes. Wipe away the excess GLUE.
å Now, fill the holes in the RIGHT END (EE2) 1/4 to 1/2 full with
GLUE. Be sure to fill the second and fourth holes from the
rounded edge as shown.
å Fasten the RIGHT END (EE2) to the BACK PANEL (I3). Tighten two
HIDDEN CAMS. Wipe away the excess glue
å NOTE: Be sure the WOOD DOWELS in the BACK PANEL insert
into the holes in the RIGHT END.
Step 5
411222www.sauder.com/services Page 9
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
EE2
I3
Right End
Rounded edge
Roller end
Inspect the parts thoroughly before
assembling. Disassembly of glued
parts is extremely dicult.
Caution
!
15F
15F
Surface with HIDDEN CAMS
177M
Fill the holes 1/4 to 1/2 full with GLUE.

Step 6
411222 www.sauder.com/servicesPage 10
Arrow
Minimum
190 degrees
Maximum
210 degrees
C3
I3
Surface with
HIDDEN CAMS
These holes
must be here.
Roller end
15F
15F
å First, fill the hole in the short edge of the UPRIGHT (C3) 1/4 to 1/2
full with GLUE (177M). Then, insert a WOOD DOWEL (15F) into the
hole. Wipe away the excess GLUE.
å Next, fill the two holes in the other short edge of the UPRIGHT (C3)
1/4 to 1/2 full with GLUE. Then, insert two WOOD DOWELS (15F)
into these holes. Wipe away the excess GLUE.
å Now, fill the holes in the BACK PANEL (I3) 1/4 to 1/2 full with GLUE.
Be sure to fill the second and fourth holes from the top edge as
shown.
å Fasten the UPRIGHT (C3) to the BACK PANEL (I3). Tighten two
HIDDEN CAMS. Wipe away the excess glue.
å NOTE: Be sure the WOOD DOWELS in the UPRIGHT insert into the
holes in the BACK PANEL.
Inspect the parts thoroughly before
assembling. Disassembly of glued
parts is extremely dicult.
Caution
!
177M
Fill the holes 1/4 to 1/2 full with GLUE.