Sauder North Avenue User manual

TV Stand
North Avenue Collection | Model 420034
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-445-1527.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-10
Français pg 11-12
Español pg 13-15
Lot #: 388850
Date Purchased: __________________
03/08/16
Be sure to give us a ring before
making any returns. 1-800-445-1527
Your holder for all
things awesome.

Table of Contents
3
4
5-10
11-12
13-15
16-18
19
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Page 2 www.sauder.com 420034
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 50 or 95 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
WARNING
!
50 lbs.
50 lbs.
15-1/2"
15-1/2"
31-1/2"
31-1/2"
63"
63"
95 lbs.
95 lbs.
15-1/2"
15-1/2"

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A END (2)
B LONG SHELF (1)
C SHORT SHELF (1)
D SMALL SHELF (1)
E BRACE (3)
Now you know
our ABCs.
A
B
C
D
A
E
Page 3
www.sauder.com420034

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4 www.sauder.com 420034
TIE PLATE - 2
3
ALLEN WRENCH - 1
6
(Refer to the last step for proper
location and application)
522,68 22,68
WARNING LABEL - 1
(for single unit)
4
(Refer to the last step for proper
location and application)
WARNING LABEL - 1
(for two units)
5
522,68 22,68
95 lbs. 43,18 kg 43,18 kg
1-3/16" ALLEN SCREW - 18
11/2" ALLEN SCREW - 12 2

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å NOTE: Do not completely tighten the SCREWS at this time.
å Fasten the ENDS (A) to the BRACES (E). Tighten twelve 1/2"
ALLEN SCREWS (2) using the ALLEN WRENCH (6).
Page 5
www.sauder.com420034
A
A
E
E
E
6
1/2" ALLEN SCREW
(12 used in this step)
2

Step
å Slide the SHELVES (C and D) through the openings in
the ENDS (A).
å Fasten the SHELVES (C and D) to the ENDS (A) and
BRACES (E). Tighten twelve 1-3/16" ALLEN SCREWS (1)
using the ALLEN WRENCH (6).
å Completely tighten all of the SCREWS.
Step 2
Page 6 www.sauder.com 420034
6
Surface with holes
E
E
D
Surface with holes
C
A
A
1-3/16" ALLEN SCREW
(12 used in this step)
1

StepStep 3
å Fasten the LONG SHELF (B) to the ENDS (A) and
BRACE (E). Tighten six 1-3/16" ALLEN SCREWS (1)
using the ALLEN WRENCH (6).
å Carefully stand your unit upright.
Page 7
www.sauder.com420034
Surface with holes
AA
B
6
1-3/16" ALLEN SCREW
(6 used in this step)
1
E

Step
å NOTE: You can fasten two of the 420034 units side by side.
å NOTE: If not fastening two units, go to Step 6.
å If fastening two units together, remove two SCREWS from
one end of the LONG SHELF (B) and two SCREWS from the
same end of the SHORT SHELF (C).
å Repeat this step to the opposite end in the second unit.
å NOTE: You will have removed eight SCREWS.
Step 4
Page 8 www.sauder.com 420034
B
C
B
C
Remove these eight SCREWS.

å Fasten two units together using four TIE PLATES (3).
å Tighten eight 1-3/16" ALLEN SCREWS (1) (removed in Step 4) through the
TIE PLATES (3), through the ENDS (A), and into the LONG SHELVES (B) and
SHORT SHELVES (C) using the ALLEN WRENCH (6).
Step 5
Page 9
www.sauder.com420034
B
C
B
C
A
A
3
6
1

Step 6
å Apply the WARNING LABEL (4) to the top of the single unit and the WARNING LABEL (5) to one of the two units if
fastened together. You should be able to read the label when the TV is removed from the unit. When the TV is in place,
it should hide the label. Peel o the backing and apply the label as shown in the diagram.
å NOTE: This is a permanent label intended to last for the life of the product. Once applied, do not try to remove it.
å NOTE: Please read the back pages of the instruction booklet for important safety information.
å This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry.
Page 10 www.sauder.com 420034
522,68 22,68
95 lbs. 43,18 kg 43,18 kg
5,8 ,8
4
5
30 lbs.
30 lbs.
50 lbs.
95 lbs. total
30 lbs.
30 lbs.
30 lbs.
30 lbs.
And to celebrate, why not share your success story?
5
4