Sauder 430083 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
English pg 1-24
Français pg 25-28
Español pg 29-32
Lot # 558975 01/06/21
Purchased: __________________
Wardrobe/Storage Cabinet
Model 430083
Store behind
closed doors.

Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
3
4
5
6-24
25-28
29-32
33-34
35
Page 2 www.sauder.com/service 430083
Electric drill with 1/8" or 3/8" bit
(ONLY in indicated step)
Pencil

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A LEFT END (1)
B RIGHT END (1)
C UPRIGHT (1)
D TOP (1)
E BOTTOM (1)
F LARGE SHELF (1)
G BASE (2)
H LEFT DOOR (1)
J RIGHT DOOR (1)
K CENTER DOOR (1)
L BRACE (1)
M ADJUSTABLE SHELF (2)
N BACK (1)
O SMALL SHELF (1)
P TOP MOLDING (1)
A
B
C
D
E
F
G
G
H
J
K
L
M
M
N
O
P
Page 3www.sauder.com/service430083

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
WOOD DOWEL - 35
1HIDDEN CAM - 10 2ANGLE BRACKET - 4
4
HINGE - 9
5SHELF REST - 8 67ROD HANGER - 2 PULL - 3 8
5/8" MACHINE SCREW - 6
13
2" FLAT HEAD SCREW - 21
12
1/2" FLAT HEAD SCREW - 22
15
1/2" PAN HEAD SCREW - 12
14
APPLIQUE
CARD - 5
10
NAIL - 51
9ROD - 1 11 FURNITURE TIPPING
RESTRAINT KIT - 2
96
CAM SCREW - 10
3
Page 4 www.sauder.com/service 430083

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Page 5www.sauder.com/service430083

Step 1 Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Fasten a ROD HANGER (7) to the UPRIGHT (C). Use two
1/2" FLAT HEAD SCREWS (15) though the outer holes in
the ROD HANGER.
å Turn three CAM SCREWS (3) into the UPRIGHT(C). Flip
the UPRIGHT over and turn two CAM SCREWS into the
UPRIGHT exactly as shown.
C
C
F
L
I
P
O
V
E
R
3
3
7
Notch
Notch
1/2" FLAT HEAD SCREW
(2 used in this step)
15
1
Page 6 www.sauder.com/service 430083

å Fasten four ANGLE BRACKETS (4) to the BASES (G).
Use four 1/2" PAN HEAD SCREWS (14) as shown to
the right.
å NOTE: Be sure the edges of the ANGLE BRACKETS
are even with the edges of the BASES.
å Insert six WOOD DOWELS (1) into the BOTTOM (E).
å Fasten the ANGLE BRACKETS on the BASES (G) to
the BOTTOM (E). Use four 1/2" PAN
HEAD SCREWS (14).
å NOTE: Be sure the WOOD DOWELS in the BOTTOM
insert into the BASES.
Step 2
E
G
G
G
G
1
1
4
1/2" PAN HEAD SCREW
(8 used for the ANGLE BRACKETS)
14
Page 7www.sauder.com/service430083

å Insert two WOOD DOWELS (1) into the edge of
the UPRIGHT (C).
å Fasten the UPRIGHT (C) to the BOTTOM (E). Use two 2"
FLAT HEAD SCREWS (12).
å NOTE: Be sure the WOOD DOWELS in the UPRIGHT
insert into the BOTTOM.
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
Step 3
C
E
Notch
1
2" FLAT HEAD SCREW
(2 used in this step)
12
Page 8 www.sauder.com/service 430083
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

å Push four HIDDEN CAMS (2) into the SMALL SHELF (O).
å Insert two WOOD DOWELS (1) into the the UPRIGHT (C).
å Fasten the SMALL SHELF (O) to the UPRIGHT (C).
Tighten two HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the UPRIGHT
insert into the SMALL SHELF.
Step 4
CO
O
Notch
1
Arrow
2
2
Arrow
Finished edge
Surface with
HIDDEN CAMS
1
Page 9www.sauder.com/service430083

å Open the FURNITURE TIPPING RESTRAINT KIT (96)
and fasten the SAFETY STRAPS to the TOP (D). Use the
provided SHORT SCREWS.
å Insert two WOOD DOWELS (1) into the UPRIGHT (C).
å Fasten the TOP (D) to the UPRIGHT (C). Use two 2" FLAT
HEAD SCREWS (12).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
å NOTE: Be sure the WOOD DOWELS in the UPRIGHT
insert into the TOP.
Step 5
C
D
D
E
O
96
Use the SHORT SCREWS
from the RESTRAINT KIT.
These holes must be here.
1
2" FLAT HEAD SCREW
(2 used in this step)
12
Page 10 www.sauder.com/service 430083
(2 used)

å Insert a WOOD DOWEL (1) into the UPRIGHT (C).
å Push the TOP MOLDING (P) onto the WOOD DOWEL in
the UPRIGHT (C).
å NOTE: The TOP MOLDING should fit into the notch of
the UPRIGHT.
Step 6
P
C
1
Page 11www.sauder.com/service430083

å Fasten the TOP MOLDING (P) to the TOP (D). Use three
2" FLAT HEAD SCREWS (12).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
Step 7
P
D
2" FLAT HEAD SCREW
(3 used in this step)
12
Page 12 www.sauder.com/service 430083

Step 8
A
B
å Fasten the remaining ROD HANGER (7) to the
LEFT END (A). Use two 1/2" FLAT HEAD SCREWS (15)
though the outer holes in the ROD HANGER.
å Turn five CAM SCREWS (3) into the ENDS (A and B)
exactly as shown.
3
3
7
1/2" FLAT HEAD SCREW
(2 used in this step)
15
1
Page 13www.sauder.com/service430083

å Insert nine WOOD DOWELS (1) into the RIGHT END (B).
å Fasten the RIGHT END (B) to the TOP (D), BOTTOM (E),
BASES (G), and TOP MOLDING (P). Use seven 2" FLAT
HEAD SCREWS (12).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
å NOTE: Be sure the WOOD DOWELS in the RIGHT END
insert into the TOP, BOTTOM, BASES, SMALL SHELF, and
TOP MOLDING.
å Fasten the SMALL SHELF (O) to the RIGHT END (B).
Tighten two HIDDEN CAMS.
Step 9
B
D
E
O
2" FLAT HEAD SCREW
(7 used in this step)
12
1
1
P
G
G
1
Page 14 www.sauder.com/service 430083

Step 10
F
L
Arrow
2
å Push six HIDDEN CAMS (2) into the LARGE SHELF (F)
and BRACE (L).
2
Arrow
1
Page 15www.sauder.com/service430083

Unfinished edge
å Carefully turn your unit onto the RIGHT END (B).
å Insert three WOOD DOWELS (1) into the UPRIGHT (C).
å Fasten the LARGE SHELF (F) to the UPRIGHT (C). Tighten
two HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the UPRIGHT
insert into the LARGE SHELF.
å Fasten the BRACE (L) to the UPRIGHT (C). Tighten the
HIDDEN CAM.
å NOTE: Be sure the WOOD DOWEL in the UPRIGHT
inserts into the BRACE.
Step 11
F
L
C
1
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Page 16 www.sauder.com/service 430083
B
1

Step 12
F
L
A
D
E
å Insert ten WOOD DOWELS (1) into the LEFT END (A).
å Fasten the LEFT END (A) to the TOP (D), BOTTOM (E), BASES (G), and TOP MOLDING (P). Use seven 2" FLAT HEAD
SCREWS (12).
å NOTE: You should start each SCREW a few turns before completely tightening any of them.
å NOTE: Be sure the WOOD DOWELS in the LEFT END insert into the
TOP, BOTTOM, BRACE, BASES, LARGE SHELF, and
TOP MOLDING.
å Fasten the LARGE SHELF (F) and BRACE (L) to the LEFT END (A). Tighten three HIDDEN CAMS.
P
G
G
1
2" FLAT HEAD SCREW
(7 used in this step)
12
Surface with less holes
1
Page 17www.sauder.com/service430083
1

Step 13
å Carefully turn your unit over onto its front edges. Unfold
the BACK (N) and lay it over your unit.
å Make equal margins along all four edges of the BACK (N).
Push on opposite corners of your unit if needed to make
it "square".
å Fasten the BACK (N) to the BRACE (L). Use four 1/2" PAN
HEAD SCREWS (14).
å Fasten the BACK (N) to your unit using the NAILS (9).
å NOTE: Be sure to tap NAILS into the holes that line up
over the SHELVES (F and O).
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
Unfinished
surface
These holes must line up
over the SHELVES (F and O).
NAIL
(51 used in this step)
9
8
1/2" PAN HEAD SCREW
(4 used in this step)
14
N
Page 18 www.sauder.com/service 430083

Step 14
å Carefully stand your unit upright.
å Insert the SHELF RESTS (6) into the hole locations of your
choice in the RIGHT END (B) and UPRIGHT (C). Set the
ADJUSTABLE SHELVES (M) onto the SHELF RESTS.
6
M
M
6
(8 used)
B
C
Page 19www.sauder.com/service430083

å Fasten the HINGES (5) to the DOORS (H, J, and K). Use
eighteen 1/2" FLAT HEAD SCREWS (15).
Step 15
H
J
K
5
5
1/2" FLAT HEAD SCREW
(18 used in this step)
15
Page 20 www.sauder.com/service 430083
17