Sauder 412267 User manual

PLEASE CONTACT US
BEFORE RETURNING
YOUR UNIT TO THE STORE
1-800-523-3987
www.sauder.com
Made in the USA
Archbold, OH
NOTE: THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
English.................... Page 2-28
Français...............Pages 29-32
Espanol.............Páginas 33-36
Lot #: 354656 07 / 10 / 13
Date Purchased: ____________________
412267
Desk
Registry Row Collection

ASSEMBLY TOOLS REQUIRED
Hammer
No. 2 Phillips Screwdriver
Straight Edge Screwdriver
Tip Shown Actual Size
TABLE OF CONTENTS
Part Identification...................2-3
Hardware Identification .........3-4
Assembly Steps....................6-28
Français..............................29-32
Espanol...............................33-36
Safety .................................37-38
Warranty...................................39
A
B
C
D
E
F
G
H
U
W
X
V
I
Z
AAY
Page 2 www.sauder.com/services 412267

PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked
letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help
identify similar parts.
A RIGHT END 1
B UPPER LEFT END 1
C LOWER LEFT END 1
D UPRIGHT 1
E TOP 1
F BOTTOM 1
G MODESTY PANEL 1
H BACK 1
I BRACE 1
J UPPER DRAWER FRONT 1
D227 FILE DRAWER BACK 1
D239 DRAWER SIDE 2
MLARGE DRAWER
BOTTOM 1
NLOWER DRAWER
FRONT 1
D246 DRAWER BACK 1
D236 FILE DRAWER SIDE 2
D792 SMALL DRAWER
BOTTOM 2
RPENCIL DRAWER
FRONT 1
S PENCIL DRAWER BACK 1
D238 PENCIL DRAWER SIDE 2
U RIGHT FRONT LEG 1
V LEFT FRONT LEG 1
W RIGHT REAR LEG 1
X LEFT REAR LEG 1
Y CENTER LEG 1
Z EXTENSION BLOCK 1
AA END MOLDING 1
N
J
R
M
S
Page 3
www.sauder.com/services412267
D227 D236
D792
D239
D246
D238
D236
D792
D239
D238

HARDWARE IDENTIFICATION
HIDDEN CAM - 23
1F
GLUE - 1
KK
CAM COVER - 4
II
CAM SCREW - 13
8F
JJ CLIP - 5
CAM DOWEL- 10
2F
TACK GLIDE - 5
LL
WOOD DOWEL - 9
PP
FILE DRAWER
FRONT BRACKET - 2
MM
DRAWER FRONT
BRACKET - 1
NN PENCIL DRAWER
FRONT BRACKET - 1
OO
FILE GLIDE - 2
RR METAL BRACE - 1 TT
FOOT - 5
QQ
PULL - 2
SS
KNOB - 2
VV
WW
BACKPLATE - 2
CORNER ACCENT - 3
UU
Page 4 www.sauder.com/services 412267
40CB CABINET LEFT - 3
40CA CABINET RIGHT - 3 40CC DRAWER RIGHT - 3
40CD DRAWER LEFT - 3

HARDWARE IDENTIFICATION
Screws are shown actual size. You may receive extra hardware with your unit.
EEE SILVER 1/2" MACHINE SCREW - 5
AAA GOLD 1" MACHINE SCREW - 2
SILVER 1-1/8" FLAT HEAD SCREW -2
ZZ
BLACK 2-1/4" FLAT HEAD SCREW - 3
XX
SILVER 2" FLAT HEAD SCREW - 4
YY
BBB BLACK 7/8" MACHINE SCREW - 2
FFF GOLD 5/16" FLAT HEAD SCREW - 24
CCC BLACK 9/16" FLAT HEAD SCREW - 2
DDD BROWN 9/16" LARGE HEAD SCREW - 14
GGG NAIL - 25
Page 5
www.sauder.com/services412267

Look for this icon. It means a video
assembly tip is available at:
www.sauder.com/services/tips
1
1
S
t
e
p
Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
Push twenty-three HIDDEN CAMS (1F) into the ENDS (A and C), UPRIGHT (D), BOTTOM (F), MODESTY PANEL (G) and
BRACE (I). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM, except in the LOWER LEFT END (C) and
MODESTY PANEL (G).
I
C
A
D
F
G
Do not tighten the HIDDEN CAMS in this step.
Arrow
Arrow
Arrow
Arrow
(23 used)
(10 used)
Page 6 www.sauder.com/services 412267
Do not insert CAM DOWELS into these edges.
Do not insert CAM DOWELS into these edges.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
1F
1F
1F
2F
2F
Do not insert
CAM DOWELS
into this edge.

Turn thirteen CAM SCREWS (8F) into the LEGS (U, V, X and Y).
NOTE: Be sure to use the exact holes shown.
Y
U
V
X
(13 used)
2
2
S
t
e
p
Page 7
www.sauder.com/services412267
8F
8F

Fasten the CORNER ACCENTS (UU) to the FRONT LEGS (U, V, and Y). Use two BLACK 7/8" MACHINE SCREWS through the
FRONT LEGS (U and Y). Use a SILVER 1/2" MACHINE SCREW through the LEFT FRONT LEG (V).
EEE
SILVER 1/2" MACHINE SCREW
(1 used in this step)
V
Y
U
BLACK 7/8" MACHINE SCREW
(2 used in this step)
BBB
Angled edge
UU
UU
3
3
S
t
e
p
Page 8 www.sauder.com/services 412267

Fasten the RIGHT FRONT LEG (U) to the RIGHT END (A) and the CENTER LEG (Y) to the UPRIGHT (D). Tighten six
HIDDEN CAMS.
4
4
S
t
e
p
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Angled edge
Angled edge
U
A
D
Y
Page 9
www.sauder.com/services412267
Edge with CAM DOWELS

BLACK 2 1/4" FLAT HEAD SCREW
(3 used in this step)
XX
CCC
Carefully turn the RIGHT END (A) over.
Turn two BLACK 9/16" FLAT HEAD SCREWS (CCC) into the END (A) until the shoulder of the SCREWS rest on the surface of
the END.
Slide the END MOLDING (AA) onto the END (A). Line up the groove in the MOLDING over the head of the SCREWS in the END
and slide it until it is against the RIGHT FRONT LEG (U).
Fasten the RIGHT REAR LEG (W) to the RIGHT END (A). Use three BLACK 2 1/4" FLAT HEAD SCREWS (XX).
5
5
S
t
e
p
Apply pressure with your hands as
you guide the MOLDINGS over
the SCREWS and onto the END.
BLACK 9/16" FLAT HEAD SCREW
(2 used in this step)
Angled edge
Shoulder
AA
AA
W
A
U
Page 10 www.sauder.com/services 412267

First, fill the holes in one end of the UPPER LEFT END (B) 1/4 to 1/2 full with GLUE (KK). Then, insert two WOOD
DOWELS (PP) into these holes. Wipe away the excess GLUE.
Repeat this step for the other end of the UPPER LEFT END (B) and both ends of the LOWER LEFT END (C) and BRACE (I)
as shown above.
Now, fasten the BRACE (I) to UPPER LEFT END (B). Use two SILVER 1-1/8" FLAT HEAD SCREWS (ZZ).
6
6
S
t
e
p
Inspect the parts thoroughly before
assembling. Disassembly of glued parts
is extremely difficult..
Caution
Fill the hole 1/4 to 1/2 full with GLUE
SILVER 1-1/8" FLAT HEAD SCREW
(2 used in this step)
ZZ
Surface with
HIDDEN CAMS
I
+
+
Surface with
HIDDEN CAMS
Edge with
HIDDEN CAMS
The holes should be
closer to this edge.
C
B
KK
KK
PP
PP
(8 used)
Page 11
www.sauder.com/services412267
If the UPPER LEFT END (B) has an
unfinished surface, it should be facing up.

7
7
S
t
e
p
First, fill the four holes in the edge of the LEFT REAR LEG (X) 1/4 to 1/2 full with GLUE (KK). Then, insert the WOOD DOWELS
in the ENDS (C and B) and BRACE (I) into the holes of the LEG. Wipe away the excess GLUE.
NOTE: Be sure the CAM SCREWS insert into the holes in the short edges of the LOWER LEFT END (C) and BRACE (I).
Fasten the LEFT REAR LEG (X) to the LOWER LEFT END (C) and BRACE (I). Tighten two HIDDEN CAMS.
Repeat this step for the LEFT FRONT LEG (V) making sure all HIDDEN CAMS are tight.
Angled edge
Angled edge
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Inspect the parts thoroughly before
assembling. Disassembly of glued parts
is extremely difficult..
Caution
Fill the hole 1/4 to 1/2 full with GLUE
V
I
C
B
X
Page 12 www.sauder.com/services 412267
KK

8
8
S
t
e
p
A
D
Fasten two CABINET RIGHTS (40CA) and two CABINET LEFTS (40CB) to the RIGHT END (A) and UPRIGHT (D). Use eight GOLD
5/16" FLAT HEAD SCREWS (FFF) through holes #1 and #3.
1
1
2
2
3
3
4
4
4
4
3
3
2
2
1
1
Roller end
Roller end
GOLD 5/16" FLAT HEAD SCREW
(8 used in this step)
FFF
Edge with CAM DOWELS
Page 13
www.sauder.com/services412267
Angled edge
Angled edge

9
9
S
t
e
p
Carefully flip the UPRIGHT (D) over.
Fasten the EXTENSION BLOCK (Z) to the UPRIGHT (D). Use two SILVER 2" FLAT HEAD SCREWS (YY).
Fasten the remaining CABINET RIGHT (40CA) and CABINET LEFT (40CB) to the BRACE (I) and EXTENSION BLOCK (Z). Use four
GOLD 5/16" FLAT HEAD SCREWS (FFF) through holes #1 and #3.
1
2
34
43
21
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
FFF
Edge with CAM DOWELS
Roller end
Roller end
Z
Finished
D
I
Angled edge
Angled edge
SILVER 2" FLAT HEAD SCREW
(2 used in this step)
YY
Page 14 www.sauder.com/services 412267

10
10
S
t
e
p
Curved edge
Unfinished
Insert a WOODEN DOWEL (PP) into the hole in the TOP (E)
Fasten the BRACE (I) to the TOP (E). Tighten two HIDDEN CAMS.
NOTE: Be sure the WOODEN DOWEL inserts into the hole in the LEG.
Fasten the MODESTY PANEL (G) to the LEFT REAR LEG (X). Tighten three HIDDEN CAMS.
X
G
E
I
PP
Page 15
www.sauder.com/services412267
Surface with
HIDDEN CAMS
Caution
Risk of damage or injury. Hidden Cams must be completely tightened. Hidden Cams that are not completely tightened
will loosen, and parts may separate. To completely tighten:
210 degrees -
Tightened properly
Arrow
2
180 degrees -
Not tightened!
Arrow
1Arrow

Fasten the UPRIGHT (D) to the TOP (E). Tighten two HIDDEN CAMS.
Fasten the UPRIGHT (D) to the MODESTY PANEL (G). Use two SILVER 2" FLAT HEAD SCREWS (YY).
Fasten the METAL BRACE (TT) to the LEFT LEGS (V and X). Use four BROWN 9/16" LARGE HEAD SCREWS (DDD).
11
11
S
t
e
p
SILVER 2" FLAT HEAD SCREW
(2 used in this step)
YY
BROWN 9/16" LARGE HEAD SCREW
(4 used for the METAL BRACE)
DDD
TT
D
G
E
V
X
Page 16 www.sauder.com/services 412267
Maximum
210 degrees
Minimum
190 degrees
Arrow

Fasten the BOTTOM (F) to the UPRIGHT (D). Tighten two HIDDEN CAMS. .
Fasten the RIGHT END (A) to the BOTTOM (F) and TOP (E). Tighten four HIDDEN CAMS.
12
12
S
t
e
p
DE
F
A
Finished edge
Surface with
HIDDEN CAMS
Angled edge
Page 17
www.sauder.com/services412267
Maximum
210 degrees
Minimum
190 degrees
Arrow

Push a FOOT (QQ) over the bottom edge of each LEG (U, V, W, X, and Y).
With a hammer, tap a TACK GLIDE (LL) through the holes of the FEET (QQ).
13
13
S
t
e
p
U
V
W
X
Y
LL
QQ
(5 used)
(5 used)
Page 18 www.sauder.com/services 412267

Carefully turn your unit over onto its front edge and lay the BACK (H) over the large opening.
Fasten the BACK (H) to your unit using the NAILS (GGG).
NOTE: Be sure the BACK is not hanging over the top surface of the TOP.
14
14
S
t
e
p
The edge of the BACK
should be even with
the BOTTOM and
UPRIGHT surfaces.
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
GGG
NAIL
(20 used in this step)
Page 19
www.sauder.com/services412267
H
Finished
Surface

15
15
S
t
e
p
Pull the PENCIL DRAWER FRONT BRACKETS (OO) apart and slide them into the grooves in the DRAWER SIDES (D238).
NOTE: The DRAWER FRONT BRACKETS are marked “RH” and “LH” for easy identification.
Fasten the PENCIL DRAWER FRONT (R) to the DRAWER FRONT BRACKETS (OO). Use two BROWN 9/16” LARGE HEAD
SCREWS (DDD).
Slide the DRAWER BOTTOM (M) into the grooves in the DRAWER SIDES (D238) and DRAWER FRONT (R).
Pull the BRACKETS apart
and slide them into the
DRAWER SIDE grooves.
BROWN 9/16" LARGE HEAD SCREW
(2 used for the FRONT BRACKETS)
DDD
Unfinished
With the palm of your hand, tap the
DRAWER BOTTOM down into the groove.
Groove
1st
2nd
OO
R
M
R
Page 20 www.sauder.com/services 412267
OO
D238
D238
D238
D238
D238