Sauder 413044 User manual

PLEASE CONTACT US
BEFORE RETURNING
YOUR UNIT TO THE STORE
1-800-523-3987
www.sauder.com
Made in the USA
Archbold, OH
NOTE: THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
English.................... Page 1-18
Français...............Pages 19-21
Espanol.............Páginas 22-24
Lot #: 367569 12 / 09 / 14
Date Purchased: ____________________
413044
Entertainment
Wall System

ASSEMBLY TOOLS REQUIRED
Tip Shown Actual Size
No. 2 Phillips Screwdriver
TABLE OF CONTENTS
Part Identification.......................3
Hardware Identification .............4
Assembly Steps....................5-18
Français..............................19-21
Espanol...............................22-24
Safety .................................25-26
Warranty...................................27
33-7/8"
43-1/8"
50 lbs.
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury
or death. ATV that is too large for the available space might be accidentally pushed or bumped off the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 50 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
WARNING
Page 2 www.sauder.com/services 413044

PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked
letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help
identify similar parts.
A LARGE RIGHT END 1
B SMALL RIGHT END 1
C LARGE LEFT END 1
D SMALL LEFT END 1
E2 LARGE RIGHT UPRIGHT 1
F2 SMALL RIGHT UPRIGHT 1
G2 LARGE LEFT UPRIGHT 1
H2 SMALL LEFT UPRIGHT 1
I UPRIGHT 2
J BOTTOM 1
K UPPER SHELF 1
L TV SHELF 1
M LOWER SHELF 1
N SMALL SHELF 6
O UPPER BACK 1
P LOWER BACK 1
Q ADJUSTABLE SHELF 4
R LARGE SKIRT 1
S BRACE 2
T SMALL SKIRT 2
Page 3
www.sauder.com/services413044
A
B
C
D
E2
F2
G2
H2
I
J
K
L
M
Q
O
P
N
R
S
T
T
S
I
N
N
Q
N
Q
N
N
Q

HARDWARE IDENTIFICATION
Screws are shown actual size. You may receive extra hardware with your unit.
BROWN 7/16" LARGE HEAD SCREW - 27
GG
BLACK 1-7/8" FLAT HEAD SCREW - 56
FF
SAFETY BRACKET - 1
BB
ANGLE BRACKET - 13
YRUBBER SLEEVE - 16
AA
METAL PIN - 24
Z
HIDDEN CAM - 26
U2 CAM COVER - 16
X
CAM DOWEL - 10
V2 DOUBLE DOWEL - 8 W2
Page 4 www.sauder.com/services 413044
DD ANTI-SKID PAD - 1SCREW COVER - 24
CC
WARNING
Never use this furniture with a TV that is
too large or too heavy. Severe injury or
death can occur.The TV and furniture
will be unstable and may tip.
-The TV must less than 50 lbs.
-The base of the TV must be able to sit
completely on this shelf.
Refer to instruction book for complete
safety information.
Note: This is a permanent label. Do not
try to remove. Surface will be damaged.
08/05 2 6 9 2 2 0 269220
WARNING LABEL - 1
EE
(Refer to the last step for proper location and application)

Look for this icon. It means a video
assembly tip is available at:
www.sauder.com/services/tips
1
1
S
t
e
p
Page 5
www.sauder.com/services413044
Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
Push ten HIDDEN CAMS (U2) into the BOTTOM (J), TV SHELF (L), and LOWER BACK (P) as shown in the upper diagram.
Then, insert the metal end of a CAM DOWEL (V2) into each HIDDEN CAM.
Push sixteen HIDDEN CAMS (U2) into the LARGE ENDS (A and C), LARGE UPRIGHTS (E2 and G2), SMALL ENDS (B and D),
and SMALL UPRIGHTS (F2 and H2) as shown in the lower diagram.
Do not tighten the HIDDEN CAMS in this step.
(10 used)
Do not insert CAM
DOWELS into these parts.
J
L
P
(16 used)
A
C
E2
G2
F2
H2
B
D
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Arrow
U2
Arrow
Arrow
U2
V2
U2
V2
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=976
to watch a video on how to assemble your unit.

Fasten the LARGE UPRIGHTS (E2 and G2) to the UPPER SHELF (K). Use four BLACK 1-7/8" FLAT HEAD SCREWS (FF).
2
2
S
t
e
p
Page 6 www.sauder.com/services 413044
K
E2
G2
Finished edge
Finished edge
Finished edge
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
FF

3
3
S
t
e
p
Page 7
www.sauder.com/services413044
Fasten four SMALL SHELVES (N) to the LARGE UPRIGHTS (E2 and G2). Use eight BLACK 1-7/8" FLAT HEAD SCREWS (FF).
BLACK 1-7/8" FLAT HEAD SCREW
(8 used in this step)
FF
E2
G2
N
N
N
N
Finished edge
Finished edge

4
4
S
t
e
p
Page 8 www.sauder.com/services 413044
Fasten the TV SHELF (L) to the LARGE UPRIGHTS (E2 and G2). Tighten four HIDDEN CAMS.
Fasten both BRACES (S) to the LARGE UPRIGHTS (E2 and G2), UPPER SHELF (K), and TV SHELF (L). Use fourteen BLACK
1-7/8" FLAT HEAD SCREWS (FF).
BLACK 1-7/8" FLAT HEAD SCREW
(14 used in this step)
FF
E2
G2
S
L
K
Finished edge
Surface with
HIDDEN CAMS
Finished edge
Finished surface
S
Finished surface
Caution
Risk of damage or
injury. Hidden Cams
must be completely
tightened. Hidden
Cams that are not
completely tightened
may loosen, and parts
may separate.
To completely tighten:
Start Tighten
Arrow
Maximum
210 degrees
Minimum
190 degrees
Arrow

5
5
S
t
e
p
Page 9
www.sauder.com/services413044
K
N
N
N
N
E2
G2
O
A
C
Finished surface
Finished edge
Finished edge
Fasten the UPPER BACK (O) to the UPPER SHELF (K) and LARGE UPRIGHTS (E2 and G2). Use five BLACK 1-7/8" FLAT
HEAD SCREWS (FF).
Fasten the LARGE ENDS (A and C) to the SMALL SHELVES (N). Use eight BLACK 1-7/8" FLAT HEAD SCREWS (FF).
BLACK 1-7/8" FLAT HEAD SCREW
(13 used in this step)
FF

6
6
S
t
e
p
Page 10 www.sauder.com/services 413044
N
N
B
D
F2
H2
Finished edge
Finished edge
Finished edge
Finished edge
Fasten the SMALL ENDS (B and D) and SMALL UPRIGHTS (F2 and H2) to the remaining SMALL SHELVES (N). Use eight
BLACK 1-7/8" FLAT HEAD SCREWS (FF).
BLACK 1-7/8" FLAT HEAD SCREW
(8 used in this step)
FF