Sauder Harbor View 423661 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-22
Français pg 23-25
Español pg 26-28
Lot # 519821 09/24/18
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Storage Cabinet
Harbor View Collection | Model 423661
Store behind
closed doors.

Table of Contents Assembly Tools Required
3
4
5-22
23-25
26-28
29-30
31
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
423661 www.sauder.com/servicesPage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A LARGE END (2)
B TOP (1)
C FRONT MOLDING (1)
D RIGHT MOLDING (1)
E LEFT MOLDING (1)
F SMALL END (2)
G END MOLDING (2)
H VALANCE (1)
J UPPER SHELF (1)
K BOTTOM (1)
L SHELF (1)
M ADJUSTABLE SHELF (1)
N BASE (1)
O RIGHT DOOR (1)
P LEFT DOOR (1)
Q SMALL BACK (1)
R LARGE BACK (1)
Now you know
our ABCs.
423661www.sauder.com/services Page 3
A
B
C
D
E
F
G
H
J
K
L
M
N
O
P
Q
R
G
A
F

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
423661 www.sauder.com/servicesPage 4
SAFETY STRAP - 1
Locate this nylon SAFETY
STRAP (60M) to be used
later in assembly. Do not
accidentally throw away.
60M SAFETY DRYWALL
ANCHOR - 1
61M
WASHER - 1
13M
BLACK 9/16" LARGE HEAD SCREW - 27
1S BLACK 1-1/8" PAN HEAD SCREW - 2
9S
BLACK 1/2" FLAT HEAD SCREW - 8
11S SILVER 2" FLAT HEAD SCREW - 7
57S
BLACK 1-15/16" FLAT HEAD SCREW - 4
113S
BUMPER CARD - 1
160M
MOLDING
CONNECTOR - 2
18F 36F TWIST-LOCK®
FASTENER - 16 TIE PLATE - 4
3G METAL BRACKET - 9 4G
13H HINGE - 4 KNOB - 2
134K
NAIL - 72
1N METAL PIN - 4 1R RUBBER SLEEVE - 4 2R

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push sixteen SAUDER TWIST-LOCK®
FASTENERS (36F) into the large holes in the ENDS (A),
SMALL ENDS (F), BOTTOM (K), and SHELF (L).
423661www.sauder.com/services Page 5
(16 used)
36F
Do not tighten the TWIST-LOCK® FASTENERS in this step.
36F
A
F
K
L
A
F
Some assembly
(and snacks) required.

Step 2
å Tap two MOLDING CONNECTORS (18F) into the notches
in the MOLDINGS (C, D, and E).
423661 www.sauder.com/servicesPage 6
Flat end
Flat end
Use your hammer to tap the MOLDING CONNECTORS (18F) into the notches in the MOLDINGS.
C
E
D
18F
18F

å Carefully turn the MOLDINGS (C, D, and E) over.
å Fasten the MOLDINGS (C, D, and E) to the TOP (B). Use
seven SILVER 2" FLAT HEAD SCREWS (57S).
å NOTE: Do not overtighten the SCREWS into the TOP.
å Fasten the SAFETY STRAP (60M) to the TOP (B). Use one
BLACK 9/16" LARGE HEAD SCREW (1S).
å NOTE: Position the SAFETY STRAP (60M) exactly as shown.
Step 3
423661www.sauder.com/services Page 7
B
C
E
D
60M
BLACK 9/16" LARGE HEAD SCREW
(1 used for the SAFETY STRAP)
1S
Surface with holes
SILVER 2" FLAT HEAD SCREW
(7 used for the MOLDINGS)
57S
Curved edge

Step 4
å Fasten four METAL BRACKETS (4G) to the SMALL ENDS (F).
Use four BLACK 9/16" LARGE HEAD SCREWS (1S).
å NOTE: Be sure the METAL BRACKETS are even with the edges
of the SMALL ENDS.
å Fasten the END MOLDINGS (G) to the SMALL ENDS (F). Use
four BLACK 9/16" LARGE HEAD SCREWS (1S) through the
METAL BRACKETS on the SMALL ENDS and into the holes in
the END MOLDINGS.
423661 www.sauder.com/servicesPage 8
F
F
BLACK 9/16" LARGE HEAD SCREW
(8 used for the METAL BRACKETS)
1S
4G
F
F
G
G
4G
Edge with
TWIST-LOCK®
FASTENERS
These holes are
closer to this edge.
These surfaces
should be even.

å Fasten the SMALL ENDS (F) to the MOLDINGS (D and E).
Tighten four TWIST-LOCK® FASTENERS.
Step 5
423661www.sauder.com/services Page 9
E
D
F
Surface with
TWIST-LOCK®
FASTENERS
F
Surface without
TWIST-LOCK®
FASTENERS
How to use the SAUDER TWIST-LOCK® FASTENER
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end

Step 6
å Fasten four TIE PLATES (3G) to the VALANCE (H). Use
four BLACK 9/16" LARGE HEAD SCREWS (1S).
å Fasten the VALANCE (H) to the FRONT MOLDING (C)
and END MOLDINGS (G). Use four BLACK 9/16" LARGE
HEAD SCREWS (1S) through the TIE PLATES and into the
holes in the MOLDINGS.
423661 www.sauder.com/servicesPage 10
BLACK 9/16" LARGE HEAD SCREW
(8 used for the TIE PLATES)
1S
G
C
H
H
3G
3G
3G
Curved edge
G