Sauder worksense MASON PEAK Hutch 427809 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Sauder.com
Share your journey!
How can we help you? To reach our customer service, visit sauder.com/oceservice to chat with a
live rep or email us.
Prefer the phone? Give us a ring at
877-996-7539 .
Our award-winning team is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays).
Lot # 560911 03/25/21
Purchased: __________________
English pg 1-28
Français pg 29-32
Español pg 33-36
MASON PEAK COLLECTION
Hutch
Prime Oak finish | Model 427809

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
4
5
6-28
29-32
33-36
37-38
39
Hammer
Not actual size
Nail Holder (provided)
Tape Measure
Electric drill with 1/8" bit
(ONLY in indicated step)
Pencil
å This piece of furniture accommodates the following optional accessory (sold separately).
Optional Accessory (sold separately)
å LED Light (Item 426494)
The LED Light is designed to be fastened to the underside of a hutch.
å To purchase the LED Light, scan this QR code. (Or go to sauder.com)
427809 www.sauder.com/oceservicePage 2

Part Identification Now you know
our ABCs.
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C TOP MOLDING (1)
D RIGHT TOP MOLDING (1)
E LEFT TOP MOLDING (1)
F LARGE UPRIGHT (1)
G SMALL UPRIGHT (1)
H LARGE UPRIGHT MOLDING (1)
J SMALL UPRIGHT MOLDING (1)
K UPPER SHELF (1)
L UPPER SHELF MOLDING (1)
M EXTENSION BLOCK (1)
N BACK (2)
O BRACE (1)
P SHORT BACK PANEL (1)
Q LONG BACK PANEL (1)
R TOP (1)
S LOWER SHELF (1)
T DOOR (2)
A
B
C
D
E
F
G
H
K
L
M
N
O
P
Q
R
S
T
T
N
J
427809www.sauder.com/oceservice Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
HIDDEN
CAM - 2
1F CAM
DOWEL - 2
2F WOOD
DOWEL - 10
15F MOLDING
CONNECTOR - 2
17F 37F TWIST-LOCK®
FASTENER - 12
BRACKET CONNECTOR - 2
81G
DOOR
HANGER - 4
40G CLIP - 5 67G DOOR
STOP - 2
4I 191K PULL - 2
FURNITURE TIPPING
RESTRAINT KIT - 1
97
DOOR SLIDE - 4
37M NAIL - 36
1N
BLACK 9/16" LARGE HEAD SCREW - 17
1S SILVER 1-1/8" FLAT HEAD SCREW - 2 10S
BLACK 2-1/4" FLAT HEAD SCREW - 8
26S BLACK 7/8" MACHINE SCREW - 4 37S
BLACK 1-15/16" FLAT HEAD SCREW - 2
113S
SILVER 1" LARGE HEAD SCREW - 8
102S
427809 www.sauder.com/oceservicePage 4
4P CORD CLIP - 1
SILVER 1-5/8" FLAT HEAD SCREW - 8
152S
74P SCREW
COVER - 4
TWIST-LOCK®
FASTENER COVER - 12
105P

Hardware Usage Guide
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
2.
Push a TWIST-LOCK® FASTENER
into the large hole in the part.
1.
HOW TO USE A TWIST-LOCK®FASTENER
HOW TO USE A HIDDEN CAM & CAM DOWEL 2. Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
1. Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the edge
of the board.
Hole
Arrow
Metal end
Hidden Cam
Cam Dowel
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
3.
427809www.sauder.com/oceservice Page 5

Step 1 Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code. 0
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Tap two MOLDING CONNECTORS (17F) into the notches
in the TOP MOLDINGS (C, D, and E).
Flat end
Flat end
Use your hammer to tap the MOLDING CONNECTORS (17F) into the notches in the MOLDINGS.
17F
17F
Unfinished surface
CD
E
Some assembly
(and snacks) required.
427809 www.sauder.com/oceservicePage 6

Step 2
å Fasten the TOP MOLDINGS (C, D, and E) to the TOP (R).
Use eight SILVER 1-5/8" FLAT HEAD SCREWS (152S).
å NOTE: Start each SCREW a few turns before completely
tightening any of them.
å NOTE: Do not overtighten the SCREWS into the TOP.
Surface with holes
C
D
E
R
Meet Part (R). This component has
been engineered to be lighter, stronger,
faster… well ok. Not technically faster.
But definitely makes for a sturdier
Hutch that’s easier to assemble and
friendlier to the environment.
427809www.sauder.com/oceservice Page 7
SILVER 1-5/8" FLAT HEAD SCREW
(8 used in this step)
152S

Step 3
å Fasten one DOOR SLIDE (37M) to the RIGHT END (A). Use
two BLACK 9/16" LARGE HEAD SCREWS (1S).
å Push two SAUDER TWIST-LOCK® FASTENERS (37F) into the
large holes in the RIGHT END (A).
å Fasten the RIGHT END (A) to the RIGHT TOP MOLDING (D).
Tighten two TWIST-LOCK® FASTENERS.
BLACK 9/16" LARGE HEAD SCREW
(2 used in this step)
1S
37M
D
A
Barrel end
2
37F
A
Barrel end
These holes must be here.
C
Part (A). Another
sturdier, easier,
friendlier component!
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
427809 www.sauder.com/oceservicePage 8

Step 4 2
å Push two SAUDER TWIST-LOCK® FASTENERS (37F) into the
large holes in the LARGE UPRIGHT (F).
å Fasten the EXTENSION BLOCK (M) to the LARGE UPRIGHT (F).
Use two SILVER 1-1/8" FLAT HEAD SCREWS (10S).
Do not tighten the TWIST-LOCK® FASTENERS in this step.
37F
M
F
The small hole is
closer to this edge.
SILVER 1-1/8" FLAT HEAD SCREW
(2 used in this step)
10S
427809www.sauder.com/oceservice Page 9

Step 5
å Fasten one DOOR SLIDE (37M) to the EXTENSION BLOCK (M). Use
two BLACK 9/16" LARGE HEAD SCREWS (1S).
å Carefully turn the LARGE UPRIGHT (F) over.
å Partially fasten one DOOR SLIDE (37M) to the LARGE UPRIGHT (F).
Use one BLACK 9/16" LARGE HEAD SCREW (1S).
M
F
Barrel end
37M
37M
F
L
I
P
O
V
E
R
Barrel end
This hole will
be used in a
later step.
BLACK 9/16" LARGE HEAD SCREW
(3 used in this step)
1S
427809 www.sauder.com/oceservicePage 10