Sauder Entertainment Credenza 427465 User manual

CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-523-3987.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Entertaining what
entertains you.
Share your journey!
Entertainment Credenza
Model 427465
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-36
Français pg 37-40
Español pg 41-44
Lot # 544987 08/03/20
Purchased: __________________

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Hammer
Not actual size
WARNING
!
3
4-5
6-36
37-40
41-44
45-46
47
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 70 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
70 lbs.
70 lbs.
19"
19"
62"
62"
427465 www.sauder.com/servicePage 2
Straight Edge Screwdriver

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (2)
D ADJUSTABLE SHELF (6)
E LEG (4)
F CENTER LEG (2)
G CENTER SKIRT (1)
H SKIRT (2)
I BOTTOM (1)
J VALANCE (1)
K RIGHT DOOR MOLDING (1)
L LEFT DOOR MOLDING (1)
M BACK (1)
N TOP (1)
O RIGHT DOOR (1)
P LEFT DOOR (1)
427465www.sauder.com/service Page 3
A
B
C
DE
F
G
H
I
J
K
L
M
N
O
P
C
D
D
D
D
D
H
F
E
E
E

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
427465 www.sauder.com/servicePage 4
(Refer to Step 31 for proper
location and application)
WARNING LABEL - 1
2L
WARNING
Never use this furniture with a TV that is too
large or too heavy. Severe injury or death
can occur. The TV and furniture will be
unstable and may tip.
-The TV must less than 70 lbs.
-The base of the TV must be able to sit
completely on this shelf.
-Refer to instruction book for complete
safety information.
Note: This is a permanent label. Do not try
to remove. Surface will be damaged.
02/ 02 269224
ADJUSTABLE FOOT - 2
34E
FELT DISC CARD - 2
1M
METAL BRACKET - 14
4G PLASTIC
WASHER - 4
9I
29M BUMPER CARD - 4
TAPE CARD - 2
4M
CAM SCREW - 12
8F
WOOD DOWEL - 2
15F
HIDDEN CAM - 24
1F CAM DOWEL - 12 2F
DOOR
WHEEL - 4
98M WHEEL
SUPPORT - 4
183M107M DOOR TRACK - 1 155M RETAINING
BAR - 4 184M DOOR TRACK SUPPORT - 4
DOOR
STOP - 2
185M 189M DOOR TRACK
TUBE - 1
187M BARREL
NUT - 8188M LONG BARREL
NUT - 4
PULL - 2
131K

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
427465www.sauder.com/service Page 5
BLACK 9/16" LARGE HEAD SCREW - 36
1S BROWN 7/16" LARGE HEAD SCREW - 4 6S
15S SILVER 5/8" MACHINE SCREW - 4 BLACK 1-15/16" FLAT HEAD SCREW - 4
113S
BLACK 5/8" FLAT HEAD SCREW - 4
123S BLACK 3/8" MACHINE SCREW - 8 127S
METAL
PIN - 24
1R
HOLE PLUG - 2
41P RUBBER
SLEEVE - 24
2R
NAIL - 62
1N APPLIQUE CARD - 2
93P
149S BROWN 5/8" FLAT HEAD SCREW - 4
BLACK 5/8" LARGE HEAD SCREW - 8
140S
BROWN 1/2" PAN HEAD SCREW - 4
150S

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/service/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push eight HIDDEN CAMS (1F) into the UPRIGHTS (C)
and BOTTOM (I). Then, insert the metal end of a CAM
DOWEL (2F) into each HIDDEN CAM.
427465 www.sauder.com/servicePage 6
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
(8 used)
Do not tighten the HIDDEN CAMS in this step.
Arrow
1F
2F
C
I
C

427465www.sauder.com/service Page 7
Step 2
Do not tighten the HIDDEN CAMS in this step.
å Push four HIDDEN CAMS (1F) into the edges of the
ENDS (A and B). Then, insert the metal end of a CAM
DOWEL (2F) into each HIDDEN CAM. Some assembly
(and snacks) required.
A
B
2F
1F
Arrow

Step 3
427465 www.sauder.com/servicePage 8
å Push twelve HIDDEN CAMS (1F) into the edges of the ENDS (A
and B) and SKIRTS (G and H).
å NOTE: Be sure to use the exact holes shown in the SKIRTS (H).
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
1F
Arrow
(12 used)
Arrow
1F
A
B
G
H
H
Do not insert a HIDDEN
CAM into this hole.
Do not insert a HIDDEN
CAM into this hole.

å Turn twelve CAM SCREWS (8F) into the LEGS (E and F).
427465www.sauder.com/service Page 9
Step 4
8F
E
E
E
E
8F
8F
F
F
(12 used)

å Fasten two LEGS (E) to the RIGHT END (A). Tighten four
HIDDEN CAMS.
Step 5
427465 www.sauder.com/servicePage 10
A
E
E
Surface with
HIDDEN CAMS
1
2
Edge with
CAM DOWELS
These surfaces
should be even.
The LEGS will
overhang this edge.
These surfaces
should be even.

å Fasten the remaining LEGS (E) to the LEFT END (B).
Tighten four HIDDEN CAMS.
427465www.sauder.com/service Page 11
Step 6
The LEGS will
overhang this edge.
B
Surface with
HIDDEN CAMS
Edge with
CAM DOWELS
These surfaces
should be even.
These surfaces
should be even.
E
E

Step 7
427465 www.sauder.com/servicePage 12
å Fasten eight METAL BRACKETS (4G) to the UPRIGHTS (C)
and VALANCE (J). Use eight BLACK 9/16" LARGE
HEAD SCREWS (1S).
å NOTE: Be sure the BRACKETS are even with the edges of
the UPRIGHTS and VALANCE.
BLACK 9/16" LARGE HEAD SCREW
(8 used in this step)
1S
4G
4G
(8 used)
J
C
C
Surface with more holes

å Fasten the UPRIGHTS (C) to the TOP (N). Tighten four
HIDDEN CAMS.
427465www.sauder.com/service Page 13
Step 8
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
C
C
N
Surface with holes
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Notched edge
This hole will be
closer to this edge.
Meet Part (N). This component has been
engineered to be lighter, stronger, faster…
well ok. Not technically faster. But definitely
makes for a sturdier Entertainment
Credenza that’s easier to assemble and
friendlier to the environment.

å Fasten the VALANCE (J) to the UPRIGHTS (C). Use four
BLACK 9/16" LARGE HEAD SCREWS (1S) through the
METAL BRACKETS on the UPRIGHTS and into the holes
in the VALANCE.
Step 9
427465 www.sauder.com/servicePage 14
BLACK 9/16" LARGE HEAD SCREW
(4 used in this step)
1S
C
C
J
Surface without METAL BRACKETS
This hole will be
closer to this edge.
Now might be a
good time to refresh
your drink.

å Fasten the BOTTOM (I) to the UPRIGHTS (C). Use four
BLACK 1-15/16" FLAT HEAD SCREWS (113S).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
427465www.sauder.com/service Page 15
Step 10
C
C
BLACK 1-15/16" FLAT HEAD SCREW
(4 used in this step)
113S
I
Surface with
HIDDEN CAMS
The groove on the other surface
of the BOTTOM should be here.

å Fasten the ENDS (A and B) to the TOP (N). Tighten four
HIDDEN CAMS.
å Fasten the BOTTOM (I) to the ENDS (A and B). Tighten four
HIDDEN CAMS.
å Fasten the VALANCE (J) to the ENDS (A and B). Use four
BLACK 9/16" LARGE HEAD SCREWS (1S) through the
BRACKETS on the VALANCE and into the holes in the ENDS.
Step 11
427465 www.sauder.com/servicePage 16
Arrow
Minimum
190 degrees
Maximum
210 degrees
J
N
A
B
BLACK 9/16" LARGE HEAD SCREW
(4 used in this step)
1S
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
I

427465www.sauder.com/service Page 17
Step 12
15F
å Insert two WOOD DOWELS (15F) into the holes in the CENTER
LEGS (F) as shown in the diagram.
å Fasten the SKIRTS (G and H) to the CENTER LEGS (F). Tighten four
HIDDEN CAMS.
å NOTE: Be sure to position the LEGS and SKIRTS exactly as shown.
H
H
G
F
F
Surface with
HIDDEN CAMS
HIDDEN CAM
Groove
Groove
Groove
HIDDEN CAM
The CAM SCREW
should be closer to
the bottom edge.

Step 13
I
F
F
å Insert the WOOD DOWELS in the CENTER LEGS (F)
into the holes in the BOTTOM (I).
427465 www.sauder.com/servicePage 18
Surface with HIDDEN CAMS

Step 14
427465www.sauder.com/service Page 19
H
H
G
I
å Fasten six METAL BRACKETS (4G) to the SKIRTS (G
and H) and BOTTOM (I). Use twelve BLACK 9/16" LARGE
HEAD SCREWS (1S).
å NOTE: There are no pre-drilled holes in the SKIRTS. The
SCREWS will tighten into the grooves.
å NOTE: Start from the center of your unit and work out
towards both ENDS for proper alignment.
BLACK 9/16" LARGE HEAD SCREW
(12 used in this step)
1S
4G

Step 15
I
å Fasten the ADJUSTABLE FEET (34E) to the BOTTOM (I).
Use eight BLACK 9/16" LARGE HEAD SCREWS (1S).
å NOTE: Adjustments to the ADJUSTABLE FEET will be made
in Step 17 once your unit is standing upright.
å Peel the FELT DISCS from the FELT DISC CARDS (1M)
and stick them on the bottom of each LEG (E and F) in the
locations shown.
34E
BLACK 9/16" LARGE HEAD SCREW
(8 used in this step)
1S
E
E
E
EF
F
1M
1M
1M
427465 www.sauder.com/servicePage 20