Sauder Whitaker Point Hutch 429371 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
English pg 1-34
Français pg 35-39
Español pg 40-44
Lot # 573727 11/02/21
Purchased: __________________
Hutch
Whitaker Point Collection | Model 429371
Get all organized
and stu.

Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
Table of Contents Assembly Tools Required
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
4-5
6
6-34
35-39
40-44
45-46
47
Page 2 www.sauder.com/service 429371
Electric drill with 1/8" or 3/8" bit
(ONLY in indicated step)
Tape Measure
Pencil

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
Page 3www.sauder.com/service429371
A
B
C
D
E
F
G
H
J
M
N
Q
P
R
K
L
O
S
A LEFT END (1)
B RIGHT END (1)
C LARGE UPRIGHT (1)
D TOP (1)
E LARGE SHELF (1)
F SMALL UPRIGHT (1)
G EXTENSION BLOCK (1)
H SMALL SHELF (1)
J ADJUSTABLE SHELF (2)
K UPPER BACK (1)
L LOWER BACK (1)
M LEFT DOOR (2)
N RIGHT DOOR (1)
O DRAWER FRONT (1)
P LEFT DRAWER SIDE (1)
Q RIGHT DRAWER SIDE (1)
R DRAWER BACK (1)
S DRAWER BOTTOM (1)
J
M

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
(EXTENSION SET SHOWN SEPARATED)
LARGE WOOD
DOWEL - 39
3SMALL WOOD
DOWEL - 4
4
CAM SCREW - 30
7
LARGE HIDDEN
CAM - 28
5SMALL HIDDEN
CAM - 2
6
PULL - 1
12
Page 4 www.sauder.com/service 429371
SHELF PIN - 8
8
KNOB - 3
11
FURNITURE TIPPING
RESTRAINT KIT - 2
96
1EXTENSION
RAIL - 2 2EXTENSION SLIDE - 2
BUMPER CARD - 1
14
BACK PLATE - 2
9
HINGE - 6
13
BRACKET - 3
10
APPLIQUE CARD - 2
15

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 5www.sauder.com/service429371
22 1/2" PAN HEAD SCREW - 6 23 1/2" FLAT HEAD SCREW - 12
24 3/8" FLAT HEAD SCREW - 12
1/2" MACHINE SCREW - 2
2120 5/8" PAN HEAD SCREW - 12
7/8" MACHINE SCREW - 3
1918 1" PAN HEAD SCREW - 4
1-1/2" FLAT HEAD SCREW - 2
17
2" FLAT HEAD SCREW - 9
16

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Page 6 www.sauder.com/service 429371

Step 1
å NOTE: Save some packing foam to be used later in assembly.
å Assemble your unit on a carpeted floor or on the empty carton to
avoid scratching your unit or the floor.
å Push two LARGE HIDDEN CAMS (5) into the LARGE UPRIGHT (C).
å NOTE: Be sure to completely insert the HIDDEN CAMS into the holes.
å Turn two CAM SCREWS (7) into the LARGE UPRIGHT (C).
Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
Page 7www.sauder.com/service429371
NOTE
This is a two
person build.
5
Arrow
7
C
1

Step 2
Page 8 www.sauder.com/service 429371
C
7
å Separate the EXTENSION SLIDES (2) from the EXTENSION RAILS (1) as shown in the upper diagram below. Be
prepared, the parts are greasy.
å Fasten one EXTENSION RAIL (1) to the LARGE UPRIGHT (C). Use three 3/8" FLAT HEAD SCREW (24).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner
cartridge of the EXTENSION RAIL in to find the other holes that lines up with the holes in the UPRIGHT. Turn a SCREW
into these holes.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWER.
Push the black lever and pull the SLIDE from the RAIL.
12
Open end
3/8" FLAT HEAD SCREW
(3 used in this step)
24
1

Step 3
å Carefully turn the LARGE UPRIGHT (C) over.
å Turn two CAM SCREWS (7) into the LARGE UPRIGHT (C).
å Fasten the EXTENSION BLOCK (G) to the LARGE
UPRIGHT (C). Use four 1" PAN HEAD SCREWS (18).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
Page 9www.sauder.com/service429371
7
C
Surface without
HIDDEN CAMS
G
The small hole is
closer to this edge. 3/4"
1-3/8"
1" PAN HEAD SCREW
(4 used in this step)
18
Some assembly
(and snacks) required.

å Push four LARGE HIDDEN CAMS (5) into the LARGE SHELF (E).
å Insert two LARGE WOOD DOWELS (3) into the LARGE UPRIGHT (C).
å Fasten the LARGE SHELF (E) to the LARGE UPRIGHT (C). Tighten
two HIDDEN CAMS.
Step 4
Page 10 www.sauder.com/service 429371
Arrow
5
5
Arrow
1
C
E
E
3
Surface with
HIDDEN CAMS
Edge with
HIDDEN CAMS
The holes are
closer to this edge.
To help line up holes,
place packing foam
or books here.