Sauder Boulevard Cafe 420701 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
Share your journey!
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a rin at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Lot # 531681 09/09/19
Purchased: __________________
Enlish p 1-18
Français p 19-21
Español p 22-24
Executive Desk
Boulevard Cafe Collection | Model 420701
Sit and surf.

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
Skip the power trip.
This time.
3
4
5-18
19-21
22-24
25-26
27
Pae 2 www.sauder.com/service 420701

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
Pae 3www.sauder.com/service420701
S RIGHT END (1)
T LEFT END (1)
U RIGHT UPRIGHT (1)
V LEFT UPRIGHT (1)
W TOP (1)
X BOTTOM (2)
Y BACK (2)
Z SHELF (1)
AA MODESTY PANEL (1)
BB SMALL DRAWER FRONT (1)
CC LARGE DRAWER FRONT (2)
DD SMALL DRAWER SIDE (2)
EE SMALL DRAWER BACK (1)
FF SMALL DRAWER BOX FRONT (1)
GG DRAWER BOTTOM (3)
HH LARGE DRAWER SIDE (4)
JJ LARGE DRAWER BACK (2)
KK LARGE DRAWER BOX FRONT (2)
S
T
U
V
W
X
Y
Z
BB
DD
EE
FF
HH
JJ
X
Y
AA
GG
HH HH
JJ
KK
CC
GG
HH
KK
CC
DD
GG

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
(EXTENSION SET SHOWN SEPARATED)
L- WRENCH - 1
2624 PULL  3
21 EXTENSION SLIDE - 6 20 EXTENSION RAIL - 6
ADJUSTABLE
GLIDE - 8
25
23 FILE
HANGER  4
22 FILE
GLIDE - 4
BLACK 1-9/16" FLAT HEAD SCREW - 24
27
BLACK 7/8" HEX HEAD SCREW - 12
30
BLACK 1" HEX HEAD SCREW - 8
29
BLACK 3/4" MACHINE SCREW - 6
31
SMALL BLACK 1/2" FLAT HEAD SCREW - 18
33
LARGE BLACK 1/2" FLAT HEAD SCREW - 12
32
Pae 4 www.sauder.com/service 420701
BLACK 1-1/2" FLAT HEAD SCREW - 12
28
BLACK 3/8" MACHINE SCREW - 16
34

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty carton
to avoid scratchin your unit or the floor.
å Fasten the LEFT END (T) and one BACK (Y) to the TOP (W). Use
four BLACK 1-1/2" FLAT HEAD SCREWS (28).
å Fasten the BACK (Y) to the LEFT END (T). Use two BLACK 3/8"
MACHINE SCREWS (34).
T
W
Y
Pae 5www.sauder.com/service420701
Remember:
Rihty tihty.
Lefty loosey.
BLACK 1-1/2" FLAT HEAD SCREW
(4 used in this step)
28
BLACK 3/8" MACHINE SCREW
(2 used in this step)
34

å Fasten the LEFT UPRIGHT (V) to the TOP (W). Use two BLACK
1-1/2" FLAT HEAD SCREWS (28).
å Fasten the BACK (Y) to the LEFT UPRIGHT (V). Use two BLACK
3/8" MACHINE SCREWS (34).
Step 2
V
W
Y
Pae 6 www.sauder.com/service 420701
BLACK 1-1/2" FLAT HEAD SCREW
(2 used in this step)
28
BLACK 3/8" MACHINE SCREW
(2 used in this step)
34

å Fasten the MODESTY PANEL (AA) to the LEFT UPRIGHT (V).
Use two BLACK 3/8" MACHINE SCREWS (34).
Step 3
AA
V
Pae 7www.sauder.com/service420701
BLACK 3/8" MACHINE SCREW
(2 used in this step)
34

å Fasten the RIGHT UPRIGHT (U) to the TOP (W). Use two BLACK
1-1/2" FLAT HEAD SCREWS (28).
å Fasten the MODESTY PANEL (AA) to the RIGHT UPRIGHT (U). Use
two BLACK 3/8" MACHINESCREWS (34).
Step 4
W
U
AA
Pae 8 www.sauder.com/service 420701
BLACK 3/8" MACHINE SCREW
(2 used in this step)
34
BLACK 1-1/2" FLAT HEAD SCREW
(2 used in this step)
28

å Fasten the RIGHT END (S) and remainin BACK (Y) to the
TOP (W). Use four BLACK 1-1/2" FLAT HEAD SCREWS (28).
å Fasten the BACK (Y) to the RIGHT END (S) and RIGHT
UPRIGHT (U). Use four BLACK 3/8" MACHINE SCREWS (34).
Step 5
W
S
Y
U
Pae 9www.sauder.com/service420701
BLACK 3/8" MACHINE SCREW
(4 used in this step)
34
BLACK 1-1/2" FLAT HEAD SCREW
(4 used in this step)
28

å Fasten the SHELF (Z) to the LEFT END (T) and LEFT
UPRIGHT (V). Use four BLACK 3/8" MACHINE SCREWS (34).
Step 6
T
VZ
Pae 10 www.sauder.com/service 420701
Now miht be a
ood time to refresh
your drink.
BLACK 3/8" MACHINE SCREW
(4 used in this step)
34

å Fasten the BOTTOMS (X) to the ENDS (S and T) and
UPRIGHTS (U and V). Tihten eiht BLACK 1" HEX HEAD
SCREWS (29) usin the L-WRENCH (26).
Step 7
S
T
U
V
X
X
26
BLACK 1" HEX HEAD SCREW
(8 used in this step)
29
Pae 11www.sauder.com/service420701

Step 8
å IMPORTANT: Be sure to keep SCREWS (32) separate from SCREWS (33). Do not confuse these SCREWS.
å Separate the EXTENSION SLIDES (21) from the EXTENSION RAILS (20) as shown in the upper diaram below. Be
prepared, the parts are reasy.
å Fasten the EXTENSION RAILS (20) to the ENDS (S and T) and UPRIGHTS (U and V). Use twelve LARGE BLACK
1/2" FLAT HEAD SCREWS (32).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the 1st hole shown in the diaram. Then, slide the inner
cartride of the EXTENSION RAIL in to find the other hole that lines up with the hole in the END/UPRIGHT. Turn a
SCREW into this hole.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.
2021
Push the black lever up and
pull the SLIDE from the RAIL. Open end 1st hole
1st hole
S
T
U
V20
20
LARGE BLACK 1/2" FLAT HEAD SCREW
(12 used in this step)
32
Pae 12 www.sauder.com/service 420701
Open end

å Turn eiht ADJUSTABLE GLIDES (25) into the bottoms of
the ENDS (S and T) and UPRIGHTS (U and V).
Step 9
S
T
U
V
25
Pae 13www.sauder.com/service420701

Step 10
DD
EE
FF
DD
EE
FF
GG
å Fasten the remainin SMALL DRAWER SIDE (DD) to the SMALL
DRAWER BACK (EE) and SMALL DRAWER BOX FRONT (FF).
Use four BLACK 1-9/16" FLAT HEAD SCREWS (27).
å NOTE: Be sure the DRAWER BOTTOM (GG) inserts into the
roove of the SMALL DRAWER SIDE (DD).
12
3
å Fasten one SMALL DRAWER SIDE (DD) to the
SMALL DRAWER BACK (EE) and SMALL DRAWER
BOX FRONT (FF). Use four BLACK 1-9/16" FLAT
HEAD SCREWS (27).
å Slide one DRAWER BOTTOM (GG) into the rooves in
the SMALL DRAWER SIDE (DD), the SMALL DRAWER
BACK (EE), and the SMALL DRAWER BOX FRONT (FF).
Groove
Be sure the
DRAWER
BOTTOM
inserts into
the DRAWER
SIDE roove.
DD
EE
FF
GG
Be sure the DRAWER
BOTTOM inserts into the
DRAWER SIDE roove.
BLACK 1-9/16" FLAT HEAD SCREW
(4 used in Section 1)
27
BLACK 1-9/16" FLAT HEAD SCREW
(4 used in Section 3)
27
Pae 14 www.sauder.com/service 420701

å First, fasten one PULL (24) to the SMALL DRAWER FRONT (BB). Use two
BLACK 3/4" MACHINE SCREWS (31).
å Second, fasten the SMALL DRAWER FRONT (BB) to the SMALL
DRAWER BOX FRONT (FF). Tihten four BLACK 7/8" HEX HEAD
SCREWS (30) usin the L-WRENCH (26).
å Fasten two EXTENSION SLIDES (21) to the SMALL DRAWER SIDES (DD).
Use six SMALL BLACK 1/2" FLAT HEAD SCREWS (33).
å NOTE: Use the 1st, 4th, and 7th holes from the
OPEN END in the EXTENSION SLIDE.
Step 11
FF
BB
24
21
21
Open end
Open end
DD
DD
1st
7th
4th
1st
7th
4th
SMALL BLACK 1/2" FLAT HEAD SCREW
(6 used for the SLIDES)
33
1st
2nd
BLACK 7/8" HEX HEAD SCREW
(4 used in this step)
30
BLACK 3/4" MACHINE SCREW
(2 used for the PULL)
31
Pae 15www.sauder.com/service420701
26
If you're doin this to
help a friend, don't
leave without a bite.

Step 12
HH
JJ
KK
HH
JJ
KK
GG
å Fasten the LARGE DRAWER SIDE (HH) to the LARGE
DRAWER BACK (JJ) and LARGE DRAWER BOX FRONT (KK).
Use four BLACK 1-9/16" FLAT HEAD SCREWS (27).
å NOTE: Be sure the DRAWER BOTTOM (GG) inserts into the
roove of the LARGE DRAWER SIDE (HH).
å Repeat this step for the other lare drawer.
12
3
å Fasten one LARGE DRAWER SIDE (HH) to the
LARGE DRAWER BACK (JJ) and LARGE DRAWER
BOX FRONT (KK). Use four BLACK 1-9/16" FLAT
HEAD SCREWS (27).
å Slide one DRAWER BOTTOM (GG) into the rooves in
the LARGE DRAWER SIDE (HH), the LARGE DRAWER
BACK (JJ), and the LARGE DRAWER BOX FRONT (KK).
Groove
Be sure the
DRAWER
BOTTOM
inserts into
the DRAWER
SIDE roove.
HH
JJ
KK
GG
Be sure the DRAWER
BOTTOM inserts into the
DRAWER SIDE roove.
BLACK 1-9/16" FLAT HEAD SCREW
(8 used in Section 1)
27
BLACK 1-9/16" FLAT HEAD SCREW
(8 used in Section 3)
27
Pae 16 www.sauder.com/service 420701

Step 13
å First, fasten one PULL (24) to the LARGE DRAWER FRONT (CC). Use two BLACK 3/4" MACHINE SCREWS (31).
å Second, fasten the LARGE DRAWER FRONT (CC) to the LARGE DRAWER BOX FRONT (KK). Tihten four BLACK
7/8" HEX HEAD SCREWS (30) usin the L-WRENCH (26).
å Fasten two EXTENSTION SLIDES (21) to the LARGE DRAWER SIDES (HH). Use six SMALL BLACK 1/2" FLAT
HEAD SCREWS (33).
å NOTE: Use the 1st, 4th, and 7th holes from the OPEN END in the EXTENSION SLIDE.
å Press two FILE GLIDES (22) onto the LARGE DRAWER SIDES (HH). Then place two FILE HANGERS (23) onto the
FILE GLIDES (22) as shown.
å Repeat this step for the other lare drawer.
KK
CC
24
21
21
Open end
Open end
HH
HH
1st
7th
4th
1st
7th
4th
22
23
22
23
SMALL BLACK 1/2" FLAT HEAD SCREW
(12 used for the SLIDES)
33
1st
2nd
BLACK 7/8" HEX HEAD SCREW
(8 used in this step)
30
BLACK 3/4" MACHINE SCREW
(4 used for the PULLS)
31
Pae 17www.sauder.com/service420701
26

å Carefully stand your unit upriht.
å To insert a drawer into your unit, line up the EXTENSION SLIDES on the drawer with the EXTENSION RAILS on the
unit and push the drawer into the unit until the drawer is fully inserted. The drawer will push in hard until it is all the way
in, then it will slide in and out easier.
å To level your unit, turn the ADJUSTABLE GLIDES on the bottom of the unit.
å NOTE: Please read the back paes of the instruction booklet for important safety information.
å This completes assembly. Clean with a damp cloth. Wipe dry.
Step 14
And to celebrate, why not share your success story at sauder.com or
60 lbs.
30 lbs.
30 lbs.
30 lbs.
35 lbs. each
15 lbs.
Pae 18 www.sauder.com/service 420701
NOTE: To level the unit, turn
the ADJUSTABLE GLIDES
until your unit is level.

Noter la date d’achat
de cet élément et
conserver le livret pour
future référence. Pour
contacter Sauder en
ce qui concerne cet
élément, faire référence
au numéro de lot et
numéro de modèle en
appelant notre numéro
sans frais.
Lot nº : ____________
Date de
l'achet : ____________
LISTE DE PIÈCES
REFERENCE DESCRIPTION QUANTITÉ
LISTE DE PIÈCES
REFERENCE DESCRIPTION QUANTITÉ
NOUS CONTACTER EN PREMIER
AVANT D'EFFECTUER TOUT RETOUR AU MAGASIN.
Nous faisons de notre mieux pour nous assurer que votre meuble
arrive dans d’excellentes conditions. Nos représentants du service
Clientèle sont aimables et prêts à vous aider au cas où une pièce
aurait été endommaée ou manquerait (ou si vous aviez besoin
d’aide pour l’assemblae). Composez ce numéro d’appel ratuit:
1-800-523-3987
Du lundi au vendredi, de 9 heures du matin à
5:30 heures du soir (horaire Côte Est)
(sauf jours fériés)
Si une pièce a besoin d’être remplacée, la pièce de remplacement
sera envoyée dans les 48 heures. (Sauf week-ends et jours fériés)
Utilisez les instructions d’assemblae en français avec les
schémas étape par étape du manuel d’instruction en anlais.
Chaque étape en français correspond à la même étape en
anlais. Comparer la “Liste de pièces” ci-dessous avec la “PART
IDENTIFICATION” du manuel en anlais pour vous familiariser
avec les pièces avant l’assemblae.
REMARQUE : CE MANUEL D’INSTRUCTIONS CONTIENT
D’IMPORTANTES INFORMATIONS RELATIVES À LA SÉCURITÉ.
À LIRE ET CONSERVER POUR TOUTE RÉFÉRENCE FUTURE.
(ENSEMBLE DE GLISSIÈRE ILLUSTRÉ À PART)
20 GLISSIÈRE D'EXTENSION....................................6
21 COULISSE D'EXTENSION....................................6
22 ARMATURE DE DOSSIER.....................................4
23 SUPPORT POUR DOSSIERS.............................4
24 POIGNÉE............................................................................3
25 PATIN RÉGLABLE........................................................8
26 CLÉ EN L.............................................................................1
27 VIS TÊTE PLATE 40 mm NOIRE .................24
28 VIS TÊTE PLATE 38 mm NOIRE...................12
29 VIS TÊTE HEX 25 mm NOIRE...........................8
30 VIS TÊTE HEX 22 mm NOIRE.........................12
31 VIS À MÉTAUX 19 mm NOIRE..........................6
32
GRANDE VIS TÊTE PLATE 13 mm NOIRE ...12
33 PETITE VIS TÊTE PLATE 13 mm NOIRE .. 18
34 VIS À MÉTAUX 9,5 mm NOIRE.....................16
S EXTRÉMITÉ DROITE..................................................1
T EXTRÉMITÉ GAUCHE...............................................1
U MONTANT DROIT........................................................1
V MONTANT GAUCHE.................................................1
W DESSUS...............................................................................1
X DESSOUS..........................................................................2
Y ARRIÈRE .............................................................................2
Z TABLETTE..........................................................................1
AA VOILE DE FOND ...........................................................1
BB DEVANT DE PETIT TIROIR...................................1
CC DEVANT DE GRAND TIROIR..............................2
DD CÔTÉ DE PETIT TIROIR.........................................2
EE ARRIÈRE DE PETIT TIROIR...................................1
FF DEVANT DE CAISSON DU PETIT TIROIR ....1
GG FOND DE TIROIR.........................................................3
HH CÔTÉ DE GRAND TIROIR.....................................4
JJ ARRIÈRE DE GRAND TIROIR.............................2
KK DEVANT DE CAISSON DU
GRAND TIROIR.............................................................2
Bureau exécutifModèle 420701
Pae 19www.sauder.com/service420701

ÉTAPE 6
Fixer la TABLETTE (Z) à l’EXTRÉMITÉ GAUCHE (T) et au
MONTANT GAUCHE (V). Utiliser quatre VIS À
MÉTAUX 9,5 mm NOIRES (34).
ÉTAPE 7
Fixer les DESSOUS (X) aux EXTRÉMITÉS (S et T) et aux
MONTANTS (U et V). Serrer huit VIS TÊTE HEX 25 mm
NOIRES (29) avec la CLÉ EN L (26).
ÉTAPE 8
IMPORTANT : S'assurer de bien séparer les VIS (32) des VIS (33).
Ne pas confondre ces VIS.
Séparer les COULISSES D'EXTENSION (21) des GLISSIÈRES
D'EXTENSION (20) comme l'indique le schéma ci-dessous
supérieure. Faire attention car les pièces sont raissées.
Fixer les GLISSIÈRES D'EXTENSION (20) aux EXTRÉMITÉS (S
et T) et aux MONTANTS (U et V). Utiliser douze GRANDE VIS
TÊTE PLATE 13 mm NOIRES (32).
REMARQUE : Pour chaque GLISSIÈRE D'EXTENSION, faire tourner
une VIS dans le premier trou indiqué dans le schéma. Ensuite,
enfiler la cartouche interne de la GLISSIÈRE D'EXTENSION vers
l'intérieur pour trouver l'autre trou qui est aliné sur le trou dans
l'EXTRÉMITÉ/MONTANT. Faire tourner une VIS dans ce trou.
REMARQUE : Les COULISSES D'EXTENSION seront utilisées
ultérieurement pour les TIROIRS.
ÉTAPE 1
Assembler l'élément sur un sol à moquette ou sur le carton vide
pour éviter d'endommaer l'élément ou le sol.
Fixer l'EXTRÉMITÉ GAUCHE (T) et l'un ARRIÈRE (Y) au DESSUS (W).
Utiliser quatre VIS TÊTE PLATE 38 mm NOIRES (28).
Fixer l'ARRIÈRE (Y) à l’EXTRÉMITÉ GAUCHE (T). Utiliser deux VIS
À MÉTAUX 9,5 mm NOIRES (34).
ÉTAPE 2
Fixer le MONTANT GAUCHE (V) au DESSUS (W). Utiliser deux VIS
TÊTE PLATE 38 mm NOIRES (28).
Fixer l'ARRIÈRE (Y) au MONTANT GAUCHE (V). Utiliser deux VIS
À MÉTAUX 9,5 mm NOIRES (34).
ÉTAPE 3
Fixer le VOILE DE FOND (AA) au MONTANT GAUCHE (V). Utiliser
deux VIS À MÉTAUX 9,5 mm NOIRES (34).
ÉTAPE 4
Fixer le MONTANT DROIT (U) au DESSUS (W). Utiliser deux VIS
TÊTE PLATE 38 mm NOIRES (28).
Fixer le VOILE DE FOND (AA) au MONTANT DROIT (U). Utiliser
deux VIS À MÉTAUX 9,5 mm NOIRES (34).
Pae 20 www.sauder.com/service 420701
ÉTAPE 5
Fixer l'EXTRÉMITÉ DROITE (S) et l'autre ARRIÈRE (Y) au DESSUS (W).
Utiliser quatre VIS TÊTE PLATE 38 mm NOIRES (28).
Fixer l'ARRIÈRE (Y) à l'EXTRÉMITÉ DROITE (S) et au MONTANT
DROIT (U). Utiliser quatre VIS À MÉTAUX 9,5 mm NOIRES (34).