Sauder Pogo 414435 User manual

Made in the USA
Archbold, OH
NOTE: THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
PLEASE CONTACT US
BEFORE RETURNING
YOUR UNIT TO THE STORE
1-800-523-3987
www.sauder.com
English.................... Page 1-22
Français...............Pages 23-25
Espanol.............Páginas 26-28
Lot #: 358785 01 / 14 / 14
Date Purchased: ____________________
414435
Desk
Pogo Collection
WARNING
CHOKING HAZARD - Small Parts
Not for children under 3 years.

No. 2 Phillips Screwdriver
Tip Shown Actual Size
Hammer
ASSEMBLY TOOLS REQUIRED
TABLE OF CONTENTS
Part Identification.......................3
Hardware Identification .............4
Assembly Steps....................5-22
Français..............................23-25
Espanol...............................26-28
Safety .................................29-30
Warranty...................................31
Page 2 www.sauder.com/services 414435
ADULT ASSEMBLY REQUIRED

PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked
letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help
identify similar parts.
A2 RIGHT END 1
B2 LEFT END 1
C TOP 1
D BOTTOM 1
E MODESTY PANEL 1
F2 FRONT PANEL 1
G SIDE PANEL 1
H BACK 1
I BRACE 1
J FRONT LEG 1
K REAR LEG 1
L BASE 1
M DRAWER FRONT 1
D74 DRAWER BACK 1
D83 RIGHT DRAWER SIDE 1
D84 LEFT DRAWER SIDE 1
D705 DRAWER BOTTOM 1
R RAIL 1
S TOP MOLDING 1
D83
D84
D74
D705
A2
B2
C
D
E
F2
G
H
I
J
K
LM
R
S
Page 3
www.sauder.com/services414435

HARDWARE IDENTIFICATION
Screws are shown actual size. You may receive extra hardware with your unit.
ANGLE BRACKET - 5
5G
GOLD 5/16" FLAT HEAD SCREW - 8
3S
METAL BRACKET - 3
4G
BROWN 7/16" LARGE HEAD SCREW - 16
6S
KNOB - 1
59K
BLACK 1-1/8" PAN HEAD SCREW - 1
9S
CARD HOLDER - 1
21M
SLIDE CAM - 2
10A HIDDEN CAM - 18 1F CAM DOWEL - 10 2F
BLACK 1-7/8" FLAT HEAD SCREW - 2
2S
CAM SCREW - 8
8F
NAIL - 22
1N
WOOD DOWEL - 5
15F
GLUE - 1
8M
BLACK 9/16" FLAT HEAD SCREW - 2
32S
Page 4 www.sauder.com/services 414435
35DA CABINET RIGHT - 1 35DB CABINET LEFT - 1 DRAWER RIGHT - 1 35DC
35DD DRAWER LEFT - 1
CARD SHEET - 1
40M
SILVER 3/8" MACHINE SCREW - 2
97S
BLACK 1-9/16" FLAT HEAD SCREW - 4
30S

Look for this icon. It means a video
assembly tip is available at:
www.sauder.com/services/tips
1
1
S
t
e
p
Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
Push eighteen HIDDEN CAMS (1F) into the ENDS (A2 and B2), BOTTOM (D), MODESTY PANEL (E) and SIDE PANEL (G).
Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM, except in the long edges of the SIDE PANEL (G) and
MODESTY PANEL (E).
Page 5
www.sauder.com/services414435
A2
B2
D
G
E
Do not tighten the HIDDEN CAMS in this step.
Do not insert CAM DOWELS into these edges.
(18 used)
(10 used)
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not insert CAM DOWELS into this edge.

2
2
S
t
e
p
Page 6 www.sauder.com/services 414435
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
Roller end
Roller end
1
1
2
3
3
2
Fasten the CABINET RIGHT (35DA) and CABINET LEFT (35DB) to the ENDS (A2 and B2). Use four GOLD 5/16" FLAT HEAD
SCREWS (3S) through holes #1 and #3.
A2
B2
35DA
35DA
35DB
35DB

Flip the SIDE PANEL (G) over. Turn two BLACK 9/16" FLAT HEAD SCREWS (32S) into SIDE PANEL (G) until the shoulder of
the SCREWS rest on the surface of it.
Slide the BRACE (I) onto the SIDE PANEL (G). Line up the groove in the MOLDINGS over the head of the SCREWS in the SIDE
PANEL.
3
3
S
t
e
p
Page 7
www.sauder.com/services414435
BLACK 9/16" FLAT HEAD SCREW
(2 used in this step)
32S
Apply pressure with your hands as
you guide the MOLDINGS over
the SCREWS and onto the ENDS.
Shoulder
After sliding on the BRACE,
these edges should be even.
After sliding on the BRACE,
these edges should be even.
G
GI
I

4
4
S
t
e
p
Page 8 www.sauder.com/services 414435
Turn eight CAM SCREWS (8F) into the LEGS (J and K).
Fasten the LEGS (J and K) to the SIDE PANEL (G). Tighten six HIDDEN CAMS.
8F
8F
J
J
K
K
Caution
Risk of damage or
injury. Hidden Cams
must be completely
tightened. Hidden
Cams that are not
completely tightened
may loosen, and parts
may separate.
To completely tighten:
Start Tighten
Arrow
Maximum
210 degrees
Minimum
190 degrees
Arrow
G
These edges
should be even.
Surface with
HIDDEN CAMS
Edge with
BRACE (I)
1st
2nd
(8 used)

5
5
S
t
e
p
Page 9
www.sauder.com/services414435
Fill the hole in the top edge of the FRONT LEG (J) 1/4 to 1/2 full with GLUE (8M). Push a WOODEN DOWEL (15F) into the hole of
the FRONT LEG. Wipe away the excess GLUE.
Fill the hole in the TOP (C) 1/4 to 1/2 full with GLUE (8M).
Flip the SIDE PANEL upside down and fasten the FRONT LEG (J) and SIDE PANEL (G) to the TOP (C). Tighten two HIDDEN
CAMS. Wipe away the excess GLUE.
Maximum
210 degrees
Minimum
190 degrees
Arrow
8M
8M
G
J
C
Surface with
HIDDEN CAMS
1st
2nd J
15F

6
6
S
t
e
p
Page 10 www.sauder.com/services 414435
Fasten the MODESTY PANEL (E) to the REAR LEG (K). Tighten two HIDDEN CAMS.
E
K
Finished Surface
Finished edge