Sauder Computer Credenza 404944 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-32
Français pg 33-36
Español pg 37-40
Lot # 388778 02/15/16
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Computer Credenza
Heritage Hill Collection | Model 404944
For all your
newfangled gadgetry.

Table of Contents Assembly Tools Required
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
2-3
4-5
6-32
33-36
37-40
41-42
43
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
E TOP (1)
F BOTTOM (2)
G MODESTY PANEL (1)
H BACK (2)
I2 DOOR (1)
J ADJUSTABLE SHELF (1)
K BASE (2)
L KEYBOARD FRONT (1)
M KEYBOARD BACK (1)
N RIGHT KEYBOARD SIDE (1)
O LEFT KEYBOARD SIDE (1)
P KEYBOARD UPRIGHT (1)
Q KEYBOARD SHELF (1)
R2 KEYBOARD BOTTOM (1)
S2 LARGE DRAWER FRONT (1)
W2 DRAWER FRONT (1)
M69 TOP MOLDING (1)
D78 LARGE DRAWER BACK (1)
D86 DRAWER BACK (1)
D212 RIGHT DRAWER SIDE (1)
D213 LEFT DRAWER SIDE (1)
D260 LARGE RIGHT DRAWER SIDE (1)
D263 LARGE LEFT DRAWER SIDE (1)
D707 DRAWER BOTTOM (2)
404944 www.sauder.com/servicesPage 2
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Part Identification Now you know
our ABCs.

Part Identification
404944www.sauder.com/services Page 3
A
B
C
D
E
F
G
H
J
K
L
MN
OP
Q
R2
W2
M69 H
K
F
D86 D212
D213
D707
D707
D78 D260
D263
S2
I2

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
404944 www.sauder.com/servicesPage 4
DRAWER FRONT
BRACKET - 1
8G FILE DRAWER
FRONT BRACKET - 2
10G
FILE GLIDE - 2
15B WIDE EXTENSION
RAIL - 2
DD WIDE EXTENSION
SLIDE - 2
EE
(EXTENSION SET SHOWN SEPARATED)
AA
NARROW
EXTENSION
RAIL - 2
BB
NARROW
EXTENSION
SLIDE - 2
GG RIGHT CABINET
RAIL - 1 HH LEFT CABINET RAIL - 1
JJ LEFT DRAWER
SLIDE - 1
II RIGHT DRAWER
SLIDE - 1
(EXTENSION SET SHOWN SEPARATED)
PLASTIC PULL - 1
WW
MM TWIST-LOCK®
FASTENER - 18 HIDDEN CAM - 4
NN2
CAM DOWEL - 4
OO2 KEYBOARD
HINGE - 2
RR PULL - 3
RRR PULL MOUNT - 6 SSS
BACKPLATE - 1
UUU
KNOB - 1
TTT CORD TRAY - 2 XX ANGLE BRACKET - 13 YY
40H HINGE - 2
OUTLET - 1
1D

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
404944www.sauder.com/services Page 5
FELT DISC CARD - 1
ZZ GROMMET CAP - 1
BBB
GROMMET - 1
AAA
RUBBER SLEEVE - 4
DDD
METAL PIN - 4
CCC
BLACK 9/16" PAN HEAD SCREW - 2
NNN
BLACK 1-1/8" MACHINE SCREW - 1
HHH
BLACK 9/16" LARGE HEAD SCREW - 34
LLL
III SILVER 5/8" MACHINE SCREW - 6
BLACK 1-7/8" FLAT HEAD SCREW - 7
EEE
BROWN 1-1/2" FLAT HEAD SCREW - 6
FFF
PPP GOLD 5/16" FLAT HEAD SCREW - 24
SILVER 5/8" FLAT HEAD SCREW - 12
JJJ
SILVER 9/16" LARGE HEAD SCREW - 2
MMM
NAIL - 34
QQQ
22H
HINGE SPACER - 2
30S BLACK 1-9/16" FLAT HEAD SCREW - 8

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
404944 www.sauder.com/servicesPage 6
Do not tighten the TWIST-LOCK® FASTENERS in this step.
(18 used)
MM
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (MM) into the large holes in the RIGHT END (A)
and LEFT END (B).
å Repeat this step for the UPRIGHTS (C and D), both
BOTTOMS (F), and MODESTY PANEL (G).
A
B

Step 2
404944www.sauder.com/services Page 7
Arrow
NN2
OO2
å Push four HIDDEN CAMS (NN2) into the KEYBOARD
UPRIGHT (P). Then, insert the metal end of a CAM
DOWEL (OO2) into each HIDDEN CAM.
(4 used)
Arrow
NN2
OO2
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tighten the HIDDEN CAMS in this step.
P

å Fasten the CABINET RAILS (GG and HH) to the LEFT END (B) and LEFT UPRIGHT (D). Use four GOLD 5/16" FLAT
HEAD SCREWS (PPP).
å NOTE: The CABINET RAILS are marked "CABINET RIGHT" and "CABINET LEFT" for easy identification.
å Separate the NARROW EXTENSION SLIDES (BB) from the NARROW EXTENSION RAILS (AA) as shown in the upper
diagram below. Be prepared, the parts are greasy.
å Fasten the NARROW EXTENSION RAILS (AA) to the LEFT END (B) and LEFT UPRIGHT (D). Use four GOLD 5/16" FLAT
HEAD SCREWS (PPP).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner cartridge
of the EXTENSION RAIL out to find the other hole that lines up with the hole in the END. Turn a SCREW into this hole.
Step 3
404944 www.sauder.com/servicesPage 8
GOLD 5/16" FLAT HEAD SCREW
(8 used in this step)
PPP
Open end
Open end
Finished edge
Finished edge
Push the release lever in and pull the SLIDE from the RAIL.
AABB
Roller end
B
D
AA
AA
GG
HH
Roller end
Surface with
TWIST-LOCK®
FASTENERS
Surface with
TWIST-LOCK®
FASTENERS
Narrow

å Separate the WIDE EXTENSION SLIDES (EE) from the WIDE EXTENSION RAILS (DD) as shown in the upper diagram
below. Be prepared, the parts are greasy.
å Fasten the WIDE EXTENSION RAILS (DD) to the RIGHT UPRIGHT (C) and the other surface of the LEFT UPRIGHT (D). Use
four GOLD 5/16" FLAT HEAD SCREWS (PPP).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner cartridge
of the EXTENSION RAIL out to find the other hole that lines up with the hole in the END. Turn a SCREW into this hole.
Step 4
404944www.sauder.com/services Page 9
Push the release lever in and pull the SLIDE from the RAIL.
DDEE
C
D
Surface without
TWIST-LOCK®
FASTENERS
Surface without
TWIST-LOCK®
FASTENERS
Open end
Open end
Finished edge
Finished edge
Wide
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
PPP
DD
DD

Step 5
404944 www.sauder.com/servicesPage 10
å Fasten the MODESTY PANEL (G) to the TOP (E).
Tighten two TWIST-LOCK® FASTENERS.
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the hole of the
adjoining part.
NOTE: The dowel end of the FASTENER must remain fully
inserted in the hole of the adjoining part while locking
the FASTENER.
2. Tighten the FASTENER with a Phillips screwdriver as tight
as possible.
Dowel end
G
E
Surface without
TWIST-LOCK®
FASTENERS
Large hole
Unfinished surface
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution