Sauder Harbor View 158085 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-18
Français pg 19-21
Español pg 22-24
Lot # 391000 05/04/16
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Library
Harbor View Collection | Model 158085
The stories of your life.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
2-3
4
5-18
19-21
22-24
25-26
27
158085 www.sauder.com/servicesPage 2
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C2 TOP (1)
D SHELF (1)
E BOTTOM (1)
F ADJUSTABLE SHELF (3)
G BACK (1)
H LONG END MOLDING (2)
I SHORT END MOLDING (2)
T FEET (2)
M10 TOP MOLDING (1)
M11 BOTTOM MOLDING (1)
M36 SHELF MOLDING (1)
M55 VALANCE (1)
M56 SKIRT (1)

Part Identification Now you know
our ABCs.
A
B
C2
D
E
F
F
G
HI
M10
M36
M11
M55
M56
T
158085www.sauder.com/services Page 3
F
H
T
I

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 1-1/8" PAN HEAD SCREW - 3
9S
TIE PLATE - 4
3G ANGLE BRACKET - 14 27G
BLACK 9/16" LARGE HEAD SCREW - 37
1S BLACK 1-7/8" FLAT HEAD SCREW - 2 2S
11F TWIST-LOCK®
FASTENER - 12
FOOT SCREW - 2
23F
METAL PIN - 12
1R
CAM SCREW - 3
14F
NAIL - 41
1N
BLACK 1-7/8" PAN HEAD SCREW - 3
16S
HIDDEN CAM - 3
1F
158085 www.sauder.com/servicesPage 4
RUBBER SLEEVE - 12
2R
SAFETY STRAP - 1
Locate this nylon SAFETY
STRAP (60M) to be used
later in assembly. Do not
accidentally throw away.
60M SAFETY DRYWALL
ANCHOR - 1
61M
WASHER - 1
13M

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (11F) into the large holes in the ENDS (A and B).
å Repeat this step for the SHELF (D) and BOTTOM (E).
158085www.sauder.com/services Page 5
Do not tighten the TWIST-LOCK® FASTENERS in this step.
(12 used)
11F
A
B
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1715
to watch a video on how to assemble your unit.

å Turn three CAM SCREWS (14F) into the SHELF MOLDING (M36).
å NOTE: Be sure to use the exact holes shown.
å Push three HIDDEN CAMS (1F) into the SHELF (D).
Step 2
158085 www.sauder.com/servicesPage 6
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
Arrow
D
M36
14F
1F

Step 3
158085www.sauder.com/services Page 7
å Fasten fourteen ANGLE BRACKETS (27G) to the
ENDS (A and B). Use fourteen BLACK 9/16" LARGE
HEAD SCREWS (1S).
å NOTE: Be sure the edges of the ANGLE BRACKETS are
even with the edges of the ENDS.
BLACK 9/16" LARGE HEAD SCREW
(14 used for the ANGLE BRACKETS)
1S
(14 used)
Remember:
Righty tighty.
Lefty loosey.
27G
27G
B
A
Surface with
TWIST-LOCK®
FASTENERS
Surface with
TWIST-LOCK®
FASTENERS

Step 4
158085 www.sauder.com/servicesPage 8
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the hole of the
adjoining part.
NOTE: The dowel end of the FASTENER must remain fully
inserted in the hole of the adjoining part while locking
the FASTENER.
2. Tighten the FASTENER with a Phillips screwdriver as tight
as possible.
Dowel end
A
C2
D
E
Long finished edge
These holes
must be here.
å Fasten the RIGHT END (A) to the TOP (C2). Tighten two
TWIST-LOCK® FASTENERS.
å Fasten the SHELF (D) and BOTTOM (E) to the RIGHT
END (A). Tighten four TWIST-LOCK® FASTENERS.
Surface
with holes
Edge with
HIDDEN CAMS
Surface with
TWIST-LOCK®
FASTENERS
Surface with
TWIST-LOCK®
FASTENERS
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
Edge with
ANGLE
BRACKETS

å Fasten the LEFT END (B) to the TOP (C2), SHELF (D), and
BOTTOM (E). Tighten six TWIST-LOCK® FASTENERS.
Step 5
158085www.sauder.com/services Page 9
B
C2
D
E
Edge with
ANGLE
BRACKETS

å Fasten the TOP MOLDING (M10) to the TOP (C2). Use
three BLACK 1-7/8" PAN HEAD SCREWS (16S).
å NOTE: Do not overtighten the SCREWS into the TOP.
å Fasten the SHELF MOLDING (M36) to the SHELF (D).
Tighten three HIDDEN CAMS.
BLACK 1-7/8" PAN HEAD SCREW
(3 used in this step)
16S
Step 6
158085 www.sauder.com/servicesPage 10
These surfaces should be even.
A
B
M10
M36
D
C2
Curved edge
1
2