Sauder Boulevard Cafe 420650 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-445-1527.
Share your journey!
sauder.com
L-Shaped Desk
Boulevard Cafe Collection | Model 420650
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-38
Français pg 39-43
Español pg 44-48
Lot #: 510857
Date Purchased: __________________
12/07/17
Be sure to give us a ring before
making any returns. 1-800-445-1527
For all your
newfangled gadgetry.

Table of Contents Assembly Tools Required
3
4
5-38
39-43
44-48
49-50
51
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Page 2 www.sauder.com 420650
Straight Edge Screwdriver

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A LARGE RIGHT END (1)
B LARGE LEFT END (1)
C SMALL RIGHT END (1)
D SMALL LEFT END (1)
E LARGE UPRIGHT (1)
F SMALL TOP (1)
G LARGE TOP (1)
H SMALL RIGHT UPRIGHT (1)
I SMALL LEFT UPRIGHT (1)
J SHORT BACK (1)
K SMALL WIRE BACK (1)
L LONG BACK (1)
M LONG SHELF (2)
N LARGE WIRE BACK (1)
O BACK (1)
P SHELF TUBE (3)
Q BOX LEFT END (1)
R BOX FRONT (1)
S BOX RIGHT END (1)
T BOX BOTTOM (1)
U SHELF (1)
V RIGHT BOTTOM (1)
W LEFT BOTTOM (1)
X SHORT LEFT TUBE (2)
Y SHORT RIGHT TUBE (2)
Z LONG LEFT TUBE (1)
AA SHORT TUBE (2)
BB FRONT RIGHT TUBE (1)
CC REAR RIGHT TUBE (1)
DD LARGE DRAWER FRONT (1)
EE SMALL DRAWER FRONT (1)
FF SMALL RIGHT DRAWER SIDE (1)
GG SMALL LEFT DRAWER SIDE (1)
HH SMALL DRAWER BACK (1)
II SMALL DRAWER BOTTOM (1)
JJ LARGE RIGHT DRAWER SIDE (1)
KK LARGE LEFT DRAWER SIDE (1)
LL LARGE DRAWER BACK (1)
MM LARGE DRAWER BOTTOM (1)
NN LARGE DRAWER BRACE (1)
OO DOOR (1)
Now you know
our ABCs.
Page 3www.sauder.com420650
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
RS
T
U
V
WY
Z
BB
CC
DD
EE
FF
GG
HH
II
JJ
LL
MM
OO
M
P
P
Y
NN
AA
XKK
X

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4 www.sauder.com 420650
(EXTENSION SET SHOWN SEPARATED)
1EXTENSION RAIL - 4 2EXTENSION SLIDE - 4 LARGE CAM
SCREW - 14
4
LARGE HIDDEN
CAM - 28
3
WOOD
DOWEL - 7
7
BLACK APPLIQUE
CARD - 1
13
SMALL HIDDEN
CAM - 10
5
BLACK 1-1/2" FLAT HEAD SCREW - 21
17
L- WRENCH - 1
14
SMALL CAM
SCREW - 24
6
BROWN APPLIQUE
CARD - 1
12
METAL
BRACKET - 3
8
BLACK 1-3/8" HEX HEAD SCREW - 25
16
BLACK 5/8" PAN HEAD SCREW - 2
18
BLACK 1/2" HEX HEAD SCREW - 23
20
BLACK 1/2" LARGE HEAD SCREW - 30
19
BLACK 1/2" FLAT HEAD SCREW - 4
21 BLACK 1/2" PAN HEAD SCREW - 24 22
GROMMET
WITH CAP - 3
11
SHELF PIN - 4
9
BLACK 2-1/4" PAN HEAD SCREW - 4
15
MAGNETIC
CATCH - 1
10

Page 5www.sauder.com420650
Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty carton to
avoid scratching your unit or the floor.
å Push twenty-eight LARGE HIDDEN CAMS (3) into the SMALL
ENDS (C and D), SMALL UPRIGHTS (H and I), BACKS (J and L),
BOX FRONT (R), BOX ENDS (Q and S), and BOX BOTTOM (T).
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
Arrow
Arrow
3
C
D
H
I
J
L
R
T
Arrow
3
Arrow
3
(28 used)
S
Q

Step 2
å Turn fourteen LARGE CAM SCREWS (4) into the exact holes
shown in the TOPS (F and G), SMALL RIGHT UPRIGHT (H),
and BOX FRONT (R).
å Push ten SMALL HIDDEN CAMS (5) into the DRAWER
SIDES (FF, GG, JJ, and KK) and LARGE DRAWER BRACE (NN).
Page 6 www.sauder.com 420650
F
R
H
G
4
4
4
5
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
(10 used)
Arrow
FF
GG
JJ
NN
KK

å Turn twenty-four SMALL CAM SCREWS (6) into the exact
holes shown in the SMALL RIGHT END (C), LARGE TOP (G),
SHORT TUBES (AA), and DRAWER FRONTS (DD and EE).
å NOTE: The SMALL CAM SCREWS are turned into the metal
portion of the part.
Step 3
Page 7www.sauder.com420650
EE
G
DD
C
AA
6
(24 used)
6
6

Step
Page 8 www.sauder.com 420650
Step 4
å Fasten the LARGE LEFT END (B) to the LARGE WIRE
BACK (N). Tighten two BLACK 1-3/8" HEX HEAD
SCREWS (16) using the L-WRENCH (14).
BLACK 1-3/8" HEX HEAD SCREW
(2 used in this step)
16
14
B
N
Just think. The sooner
you do this, the sooner
you do something else.

StepStep 5
å NOTE: Be sure to keep SCREWS (19) separate from
SCREWS (22). Do not confuse these SCREWS.
å Fasten the SHELF TUBES (P) to the LONG SHELVES (M).
Use fifteen BLACK 1/2" LARGE HEAD SCREWS (19).
å NOTE: Be sure SHELF TUBES wrap around the edges of
the LONG SHELVES.
Page 9www.sauder.com420650
P
M
P
These edges
should be even.
These edges
should be even.
Surface with holes
M
P
Surface with holes
BLACK 1/2" LARGE HEAD SCREW
(15 used in this step)
19

Step
å Fasten the LONG SHELF (M) with one SHELF TUBE (P) to
the LEFT END (B). Tighten one BLACK 1-3/8" HEX HEAD
SCREW (16) using the L-WRENCH (14).
å Fasten the LONG SHELF (M) to the LARGE WIRE BACK (N).
Use five BLACK 1/2" LARGE HEAD SCREWS (19).
Step 6
14
B
N
BLACK 1-3/8" HEX HEAD SCREW
(1 used in this step)
16
Surface with screws
M
Page 10 www.sauder.com 420650
BLACK 1/2" LARGE HEAD SCREW
(5 used in this step)
19
P

StepStep 7
å Fasten the LONG SHELF (M) with two SHELF TUBES to
the LEFT END (B). Tighten two BLACK 1-3/8" HEX HEAD
SCREWS (16) using the L-WRENCH (14).
Page 11www.sauder.com420650
14
B
BLACK 1-3/8" HEX HEAD SCREW
(2 used in this step)
16
Surface with screws
M

Step
å Fasten the FRONT RIGHT TUBE (BB) to the SMALL TOP (F).
Use five BLACK 1/2" LARGE HEAD SCREWS (19).
å NOTE: Be sure the FRONT RIGHT TUBE wraps around the
edge of the SMALL TOP.
å Fasten the MAGNETIC CATCH (10) to the block on the
SMALL TOP (F) exactly as shown. Use two BLACK 5/8" PAN
HEAD SCREWS (18).
Step 8
10
BB
F
These edges
should be even.
The block on the
SMALL TOP (F)
should be here.
BLACK 5/8" PAN HEAD SCREW
(2 used for the MAGNETIC CATCH)
18
Page 12 www.sauder.com 420650
BLACK 1/2" LARGE HEAD SCREW
(5 used in this step)
19
The magnets are
on this side.

StepStep 9
å Fasten the BOX ENDS (Q and S) to the BOX FRONT (R).
Use four BLACK 1-1/2" FLAT HEAD SCREWS (17).
å Insert two WOOD DOWELS (7) into the SMALL TOP (F).
å Fasten the BOX FRONT (R) and BOX ENDS (Q and S) to
the SMALL TOP (F). Tighten five HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the SMALL TOP
insert into the BOX FRONT.
Page 13www.sauder.com420650
1
2
7
Q
R
S
Q
S
R
F
BLACK 1-1/2" FLAT HEAD SCREW
(4 used in this step)
17
The HIDDEN CAMS
are closer to the floor
and face each other.

StepStep 10
Page 14 www.sauder.com 420650
å Insert two WOOD DOWELS (7) into the BOX FRONT (R).
å Fasten the BOX BOTTOM (T) to the BOX FRONT (R).
Tighten three HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the BOX FRONT
insert into the BOX BOTTOM.
å Fasten the BOX ENDS (Q and S) to the BOX BOTTOM (T).
Use four BLACK 1-1/2" FLAT HEAD SCREWS (17).
7
T
Surface with
HIDDEN CAMS
Q
R
T
BLACK 1-1/2" FLAT HEAD SCREW
(4 used in this step)
17
S

Step
å Fasten the SMALL TOP (F) to the LEFT END (B). Tighten one
BLACK 1-3/8" HEX HEAD SCREW (16) using the L-WRENCH (14).
å Fasten the SMALL TOP (F) to the LARGE WIRE BACK (N). Use
five BLACK 1/2" LARGE HEAD SCREWS (19).
Step 11
Page 15www.sauder.com420650
14
BLACK 1-3/8" HEX HEAD SCREW
(1 used in this step)
16
F
N
B
BLACK 1/2" LARGE HEAD SCREW
(5 used in this step)
19

Step
å NOTE: Do not completely tighten the SCREWS in this step.
å Fasten the BACK (O) and RIGHT BOTTOM (V) to the
LARGE RIGHT END (A). Tighten five BLACK 1/2" HEX
HEAD SCREWS (20) using the L-WRENCH (14).
Step 12
Page 16 www.sauder.com 420650
14
BLACK 1/2" HEX HEAD SCREW
(5 used in this step)
20
A
O
V
Don't worry. It isn't
Rome. This can be built
in a day.

StepStep 13
å NOTE: Do not completely tighten the SCREWS in this step.
å Fasten the SHORT RIGHT TUBES (Y) to the RIGHT END (A).
Tighten two BLACK 1-3/8" HEX HEAD SCREWS (16) using
the L-WRENCH (14).
Page 17www.sauder.com420650
14
A
Y
Y
BLACK 1-3/8" HEX HEAD SCREW
(2 used in this step)
16

Step
å Fasten the LARGE UPRIGHT (E) to the BACK (O). Tighten three BLACK 1/2"
HEX HEAD SCREWS (20) using the L-Wrench (14).
å Fasten the LARGE UPRIGHT (E) to the RIGHT BOTTOM (V). Tighten two
BLACK 1/2" HEX HEAD SCREWS (20) using the L-Wrench (14).
å Fasten the LARGE UPRIGHT (E) to the SHORT RIGHT TUBES (Y). Tighten
two BLACK 1-3/8" HEX HEAD SCREWS (16) using the L-Wrench (14).
å NOTE: Now, completely tighten all of the SCREWS from Steps 12-14.
Step 14
Page 18 www.sauder.com 420650
14
BLACK 1-3/8" HEX HEAD SCREW
(2 used in this step)
16
O
Y
Y
E
BLACK 1/2" HEX HEAD SCREW
(5 used in this step)
20
V

å NOTE: Start all of the SCREWS before completely
tightening any of them.
å Fasten the LARGE RIGHT END (A) to the SMALL TOP (F)
and LONG SHELVES (M). Tighten six BLACK 1-3/8" HEX
HEAD SCREWS (16) using the L-Wrench (14).
StepStep 15
Page 19www.sauder.com420650
A
F
M
M
BLACK 1-3/8" HEX HEAD SCREW
(6 used in this step)
16

Step
å Fasten the REAR RIGHT TUBE (CC) to the LARGE LEFT END (B). Tighten
one BLACK 1-3/8" HEX HEAD SCREW (16) using the L-Wrench (14).
å Fasten one METAL BRACKET (8) to the LARGE UPRIGHT (E) and REAR
RIGHT TUBE (CC) exactly as shown. Tighten two BLACK 1/2" HEX HEAD
SCREWS (20) using the L-Wrench (14).
å Fasten one METAL BRACKET (8) to the LARGE UPRIGHT (E) and FRONT
RIGHT TUBE (BB) on the SMALL TOP (F) exactly as shown. Tighten two
BLACK 1/2" HEX HEAD SCREWS (20) using the L-Wrench (14).
Step 16
Page 20 www.sauder.com 420650
14
BLACK 1/2" HEX HEAD SCREW
(4 used for the METAL BRACKETS)
20
E
F
B
CC
BB
BLACK 1-3/8" HEX HEAD SCREW
(1 used in this step)
16
Elongated hole
8
Edge with hole