Se-Kure Controls SK-554NP-RKAC-4 User manual

SK-947-RK-6
Remote Key with Small Barrel & 72" Cable
(Included with the SK-554NP-RKAC-4)
SKD-3840PLE
6' Dual Sensor – USB Sensor & Rectangular Sensor
SK-974AH
1/2" Dia. Barrel Sensor Adhesive
SK-395M
AC/DC Power Supply (5 volt. - 1 Amp)
with International Electrical Plug Ends
Installation Instructions for the
4-on-1 Alarm w/Remote Keyway
Rev. 3/13/13 P# 62097 SCI-9983©2013 Se-Kure Controls,
®Inc.
3714 Runge Street
Franklin Park, IL 60131
1-[phone]
[phone]
Fax: [phone]
On the Web:
www.se-kure.com
E-Mail:
[email protected]
SK-905
1" x 2" Rectangular Adhesive
SK-974PLE
6' Barrel Sensor
SK-554NP-RKAC-4
4-on-1 Alarm with No Power
1. Mount the Remote Key
within 72" of the Alarm
Module, and plug it into the
Remote Key Jack on the
Alarm Module.
2. Insert the key, push in and
turn clockwise. (This places
the Alarm in the “Stand-by”
position).
Note: The key can only be
removed in the “ON”
position.
3. Insert the appropriate
adapter into the SK-395M
AC/DC power supply. Plug it
into an electrical outlet, and
the other end into the AC/DC
Power Supply Jack on the
Alarm Module.
4. Choose a small flat area on
the product where the sensor
is to be applied.
VERY IMPORTANT! NOTE: Clean
the area on the display product and
the sensor with Alcohol Prep Pads.
Wipe these surfaces DRY with a
clean paper towel. If the paper
towel shows dirt, REPEAT THIS
CLEANING STEP until the sur-
faces are CLEAN & DRY!
Clean &
Wipe Dry
When replacing Adhesive
5. Remove the sensor adhesive
from its backing sheet. Apply
the adhesive pad to the bottom
of the sensor, making sure that
the center hole of the adhesive
lines up with the plunger on the
bottom of the
sensor.

Battery Test
AC/DC
Power
Supply
Jack
Remote Keyway
Jack
Horn
Assembly Instructions:
4
Sensor
Ports
The Alarm is now Ready & Active.
Additional Instructions:
1. Your alarm is equipped with 4 ports.
If only one port is used on a
displayed product a shunt plug must
be installed into any unused ports. If
this is not done the alarm will sound.
2. Prior to placing the sensor on the
product, the area where the sensor
is to be applied must be cleaned
with the alcohol wipe provided, then
thoroughly dried before attaching
the sensor.
3. For the alarm system to function the
remote key must be plugged into the
alarm unit.
4. When attaching the alarm to the
surface follow the cleaning instru-
tions for the sensor given in step 2
above.
Installation Instructions for the
4-on-1 Alarm w/Remote Keyway
Rev. 3/13/13 P# 62097 SCI-9983©2013 Se-Kure Controls,
®Inc.
3714 Runge Street
Franklin Park, IL 60131
1-[phone]
[phone]
Fax: [phone]
On the Web:
www.se-kure.com
E-Mail:
[email protected]
Battery
Connector
Cover
Plate
Remote Keyway
Jack
9-volt
Alkaline
Battery
(Not
Included)
AC/DC
Adapter
Jack
Battery
Installation:
1. Remove the (4)
phillips head screws
to open the battery
compartment as
shown in the
diagram.
2. Attach a 9-volt
Alkaline Battery
(not included) to the
connector, and insert
the battery into the
compartment.
3. Replace the
cover plate and the
(4) phillips head
screws.
Note: Tighten screw
until it stops– Do
Not Over-Tighten
Optional Battery Back-Up Installation
The 4-on-1 Alarm will operate normally without a battery, but will not alarm when
power to the SK-395M AC/DC Power Supply is interupted.
For Back-Up purposes when the circiut loses power, follow the optional battery
backup installation instructions below.
6. Remove the backing sheet from
the other side of the adhesive pad
and position the sensor over the
flat area of the display product
previously cleaned. Press the
sensor firmly into place to insure
a proper bond.
7. Following the important cleaning
steps, apply the base adhesive
to the alarm module and adhere
it to the display surface.
8. Turn the key counter clockwise
to the “ON” position and remove.