SEA JOINT Original instructions

1
JOINT
INSTALLATION MANUALS
AND SAFETY INFORMATION
REV.01 - 08/2016
Sistemi Elettronici
di Apertura Porte e Cancelli
®
SEA S.p.A.
Zona industriale 64020 S.ATTO Teramo - (ITALY)
Tel. [phone] r.a. Fax [phone]
www.seateam.com
[email protected]
67411932

2
TABLE OF CONTENTS
JOINT
Sistemi Elettronici
di Apertura Porte e Cancelli
®
PERIODICAL MAINTENANCE.................................................................................................................3
FEATURES AND SPECIFICATIONS........................................................................................................4
SAFETY OPERATING GATE....................................................................................................................5
CONFIGURATION AND SPECIFICATION................................................................................................6
CONCRETE PAD AND GATE ATTACHMENT.........................................................................................7
STANDARD INSTALLATION..................................................................................................................8
GATE ARM INSTALLATION....................................................................................................................10
GATE MOVEMENT DIRECTION............................................................................................................11
LEFT OPERATOR MOUNTING ..............................................................................................................12
RIGHT OPERATOR MOUNTING ...........................................................................................................13
MOUNTING PLATE................................................................................................................................14
TORQUE ADJUSTMENT........................................................................................................................14
LIMIT SWITCHES...................................................................................................................................15
CONTROL UNIT SUPPORT ..................................................................................................................15
MANUAL RELEASE SYSTEM................................................................................................................16
GENERAL NOTICE FOR THE INSTALLER AND THE USER ..............................................................17

3
PERIODICAL MAINTENANCE
1) Check the oil level in the hydraulic/oil-bath operators (transparent cap placed in the
Products)
2) Change the oil in case of low level
3) Check the release function
4) Check the fixing screws
5) Check the integrity of the connection cables
6) Check the function and the limit switch condition in opening and closing
7) Check for all corroded parts and replace them
8) Check the robustness and the stability of the gate; particularly the leaning and/or rotation
points of the gate ( hinges)
9) Check the operating of all accessories. Especially the functioning of all safety devices and
reversing sensors
All the above described operations MUST be made exclusively by an
authorized installer.
JOINT
Sistemi Elettronici
di Apertura Porte e Cancelli
®

4
1. Features and specifications
MECHANICAL INSTALLATION
1. lectronic control unitE
2. Hydraulic unit
3. Ground support (OPTIONAL)
4. Manual release
5. Articulated arm
6. Jack
7. Limit switch
Jointed swing operator pad mounted for residential/commercial use.
TECHNICAL FEATURES
Gate Speed: 8 - 12 seconds per 90° cycle
Maximum Gate Length: 6 mm
Maximum Gate Weight: 455 kg
Maximum Cycles: 250 cycles per day with Sea's Plug-
In Transformer. (Gate size 6 m x 2,4 m)
AC Power Supply Wire: 14 gauge or greater landscape
lighting cable rated for direct burial and
300 watts at maximum length of 305 m
305
255
483
660
305
280
Fig.1
Fig.2
Fig.3
JOINT
1
2
5
7
6
3
4
Dimensions (mm)
457
SPECIFICATIONS
Power supply
Motor power
Operation temperature
Max. beam length
Protection class
Opening time 90° (sec)
Cycles/hour
Max leaf weight
Max opening angle (degrees)
Anti-crushing protection
Limit switch
Slow-down
230V
280 W
-20°C to +55°C*
6 m
Ip44
8 - 12 sec
40
455 kg
100°
By pass valve
Mechanical/electronic
Electronic
Sistemi Elettronici
di Apertura Porte e Cancelli
®

5
The Joint 230V is for Single Home Applications
DO NOT Use for Apartment or Condominium Applications.
Owners Must Never Mount Any Gate Operating
Device Accessible Through the Gate!
2. Safety operating gate
Fig.5
MECHANICAL INSTALLATION
Fig.4
Owners Must Never Let Pedestrians Cross the Path, Step or Hang on a Moving Gate!
JOINT
Sistemi Elettronici
di Apertura Porte e Cancelli
®

6
3. Configuration and specification
Warning Signs
Attached on
Both Sides of Gate
Gate Attachment Bar Must Go Completely
Across the Gate for Full Strength
Warning Sign Clearly
Visible on Operator
100 mm Max. Width
Fig.6
MECHANICAL INSTALLATION
0 lb
90 kg
180 kg
270 kg
360 kg
450 kg
1,80 m 2,40 m 3,70 5 m 6 m
•
•
DRAWING LEAVES DIMENSIONS
USING
FIELD
JOINT
Sistemi Elettronici
di Apertura Porte e Cancelli
®

7
Example of Colum standard installation
Fig.8
Out
In 50 mm
Hinge
Center
Out
In
Hinge
Center
50
mm
Anchor
wedge
4. Concrete pad and gate attachment
Above
Ground
Below
Ground
Concrete Pad
Fig.7
150
760
400
350
Example of Ground standard installation
MECHANICAL INSTALLATION
JOINT
Sistemi Elettronici
di Apertura Porte e Cancelli
®
Dimensions (mm)

8
1030 300 100 90°
980 300 150 95°
930 300 200 100°
1020 350
970
920
L A B α
(mm) (mm) (mm)
1
2
3
4
5
6
Chart A
5. Standard installation
Sample Standard Installation is Shown on Previous Page.
Caution: If the gate is longer than 5,5 m, follow Chart A : A-2.
*Note - If this dimension is between 508 and 812 mm, compact installation is necessary.
Fig.9 Fig.10
MECHANICAL INSTALLATION
Out
In
L
Hinge
Center
B =
560 mm C =
635 mm
Long
Arm Short
Arm
Wall
Out
In
* MIN 76 mm x 90°
*
A
JOINT
1000 400
950 400
900 400
980 470
930 470
880 470
350
350
100
150
200
100
150
200
100
150
200
90°
95°
100°
90°
95°
100°
90°
95°
100°
7
8
9
10
11
12
B
α
Sistemi Elettronici
di Apertura Porte e Cancelli
®

9
Wall
min 610 mm
Fig.11
MECHANICAL INSTALLATION
JOINT
Sistemi Elettronici
di Apertura Porte e Cancelli
®

10
6. Gate arm installation
Fig.12
Incorrect
Installation
Correct
Installation
Fig.13
MECHANICAL INSTALLATION
JOINT
Sistemi Elettronici
di Apertura Porte e Cancelli
®

11
7. Gate movement direction
Open to right
Fig.15
Open to left Fig.14
MECHANICAL INSTALLATION
JOINT
Sistemi Elettronici
di Apertura Porte e Cancelli
®

12
8. Left operator mounting
Fig.16
JOINT
MECHANICAL INSTALLATION
Sistemi Elettronici
di Apertura Porte e Cancelli
®

13
9. Right operator mounting
Fig.17
JOINT
MECHANICAL INSTALLATION
Sistemi Elettronici
di Apertura Porte e Cancelli
®

14
MECHANICAL INSTALLATION
100 mm
200
mm
+-
Yellow
By-Pass Valves
+-
Grey
e
n
m
t
t
s
i
n
u
j
o
d
p
a
e
e
n
c
i
r
n
o
g
F
m
e
n
t
t
s
i
u
n
j
d
c
a
l
o
e
s
c
i
r
n
o
g
F
Regulate the opening and closing forces
of the gate respecting the force diagram.
THE MAXIMUM THRUST FORCE
D U R I N G T H E M O V E M E N T ,
MEASURED AT THE LEADING EDGE
OF LEAF, IS SUBJECTED TO THE
LAWS IN FORCE IN THE COUNTRY
WHERE THE GATE IS INSTALLED.
76 mm
10. Mounting plate
11. Torque adjustment (By-Pass Valves)
Fig.18
Fig.19
JOINT
Fig.20
Sistemi Elettronici
di Apertura Porte e Cancelli
®

15
12. Limit switches
13. Control unit support
MECHANICAL INSTALLATION
Black = Limit switch
White = Slowdown start
Opening
Closing
Fig.21
Fig.22 Fig.24
JOINT
Fig.23
Sistemi Elettronici
di Apertura Porte e Cancelli
®

16
Unlock Lock
14. Manual release system
MECHANICAL INSTALLATION
Open
Close
Fig.25 Fig.26
JOINT
Sistemi Elettronici
di Apertura Porte e Cancelli
®

17
GENERAL NOTICE FOR THE INSTALLER AND THE USER
1. Read carefully these Instructions before beginning to install the product. Store these instructions for
future reference
2. Don’t waste product packaging materials and /or circuits.
3. This product was designed and built strictly for the use indicated in this documentation. Any other use, not
expressly indicated here, could compromise the good condition/operation of the product and/or be a source
of danger. SEA S.p.A. declines all liability caused by improper use or different use in respect to the intended
one.
4. The mechanical parts must be comply with Directives: Machine Regulation 2006/42/CE and following
adjustments), Low Tension (2006/95/CE), electromgnetic Consistency (2004/108/CE) Installation must be
done respecting Directives: EN12453 and En12445.
5. Do not install the equipment in an explosive atmosphere.
6. SEA S.p.A. is not responsible for failure to observe Good Techniques in the construction of the locking
elements to motorize, or for any deformation that may occur during use.
7. Before attempting any job on the system, cut out electrical power and disconnect the batteries. Be sure
that the earthing system is perfectly constructed, and connect it metal parts of the lock.
8. Use of the indicator-light is recommended for every system, as well as a warning sign well-fixed to the
frame structure.
9. SEA S.p.A. declines all liability as concerns the automated system’s security and efficiency, if components
used, are not produced by SEA S.p.A..
10. For maintenance, strictly use original parts by SEA.
11. Do not modify in any way the components of the automated system.
12. The installer shall supply all information concerning system’s manual functioning in case of emergency,
and shall hand over to the user the warnings handbook supplied with the product.
13. Do not allow children or adults to stay near the product while it is operating. The application cannot be
used by children, by people with reduced physical, mental or sensorial capacity, or by people without
experience or necessary training. Keep remote controls or other pulse generators away from children, to
prevent involuntary activation of the system.
14. Transit through the leaves is allowed only when the gate is fully open.
15. The User must not attempt to repair or to take direct action on the system and must solely contact
qualified SEA personnel or SEA service centers. User can apply only the manual function of emergency.
16. The power cables maximum length between the central engine and motors should not be greater than 10
2
m. Use cables with 2,5 mm section. Use double insulation cable (cable sheath) to the immediate vicinity of
the terminals, in particular for the 230V cable. Keep an adequate distance (at least 2.5 mm in air), between
the conductors in low voltage (230V) and the conductors in low voltage safety (SELV) or use an appropriate
sheath that provides extra insulation having a thickness of 1 mm.
Sistemi Elettronici
di Apertura Porte e Cancelli
®

18

19

20
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
SEA S.p.A.
Zona industriale 64020 S.ATTO Teramo - (ITALY)
Tel. [phone] r.a. Fax [phone]
www.seateam.com
[email protected]