Sealey SC01 User manual

INSTRUCTIONS FOR:
2 DOOR FLOOR CABINET
MODEL No: SC01
1. SAFETY INSTRUCTIONS
2. INTRODUCTION
1.1 GENERAL SAFETY
 WARNING! Ensure Health & Safety, local authority, and general workshop practice
regulations are adhered to when using this cabinet.
 WARNING! Use caution when handling and assembling the metal components.
The metal may have sharp edges or corners, the use of protective gloves is recommended.
Locate cabinet in a suitable working area and secure to a wall with suitable fasteners.
Keep the work area clean, uncluttered and ensure there is adequate lighting.
Keep the cabinet clean and tidy in accordance with good workshop practice.
Keep children and unauthorised persons away from the working area.
DO NOT climb, step or stand on the cabinet shelves.
DO NOT use the cabinet for any purpose other than that for which it is designed.
DO NOT use in damp work areas.
 WARNING! The warnings, cautions and instructions referred to in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be understood
that common sense and caution are factors which cannot be built into this product, but must
be applied by the operator.
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE
KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
SC01 Issue No: 1 - 28/08/08
Featuring two large doors, four shelves and base storage. Added security provided by cylinder
lock and supplied with two keys. All steel construction, stabilized by an inner cross member.
Overall Size (W x D x H): 915 x 457 x 1981mm
Fig.1
3. ASSEMBLY
3.1 CONTENTS INSPECTION
Unpack all the parts and layout on the packing
material. Visually inspect all panels to check for
transportation damage.
CONTENTS
A BACK PANEL (RIGHT)
B BACK PANEL (LEFT)
C SIDE PANEL (RIGHT)
D SIDE PANEL (LEFT)
E CROSS MEMBER (INNER)
F CROSS MEMBER (OUTER)
G BOTTOM PANEL
H TOP PANEL
I DOOR PANEL WITH LOCK (RIGHT)
J DOOR PANEL (LEFT)
K SHELF
L PLASTIC INSERT
M HINGE INSERT
N RUBBER BUMPER
O SCREW (M6 X 15)
P WASHER
Q SHELF CLIP
R KEY

SC01 Issue No: 1 - 28/08/08
Fig.2
Fig.4
Fig.3
Fig.5
3.4 INNER CROSS MEMBER ASSEMBLY (Fig.4)
3.4.1 Insert the cross member (E) as shown in Fig.4 and secure using screws (O) and washers (P).
3.5 BASE ASSEMBLY (Fig.5)
3.5.1 Slidethebase(G)intopositionandlocateontothetabsonthebackandsidepanels.Thefrontedgetsovertheinnercross
member.
Fig.6 Fig.7
3.2 BACK ASSEMBLY (Fig.2)
3.2.1 Placethebackpanels(A&B)onasuitablyprotectedatsurfacetopreventscratching.
3.2.2 Interlock the tabs into the slots on the back panels and slide together until the two panels are fully engaged.
3.3 SIDE ASSEMBLY (Fig.3)
3.3.1 Holdthesidepanels(C&D)ataslightangleandtthetabsonthebackpanelsintotheslotsofthesidepanelsandslide
down to engage.
3.6 OUTER CROSS MEMBER ASSEMBLY (Fig.6)
3.6.1 Fit the outer cross member (F) and secure with the two plastic oval inserts (L) and two hinge inserts (M).
3.7 TOP ASSEMBLY (Fig.7)
3.7.1 Fitthetop(H)tothecabinetandpushdownuntilthetabslockintoposition,ttwoplasticovalinserts(L)andtwohinge
inserts (M) as shown in Fig.7. With the aid of another person carefully lift the cabinet from the top into an upright position.

01284 757500
01284 703534
[e-mail]
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
www.sealey.co.uk
Web
email
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.
SC01 Issue No: 1 - 28/08/08
Fig.9
Fig.8
3.9 SHELF ASSEMBLY (Fig.9)
3.9.1 Insert shelf clips (Q) at the desired height for each shelf and lay the shelves onto the clips.
3.10 Use a mild solution of detergent and water and wipe the unit down with a soft cloth.
3.8 DOORS ASSEMBLY (Fig.8)
3.8.1 Locate the bottom door pin into the lower bush and pull down the spring loaded top pin and align with the bush in the top
panel, release the pin to locate. Repeat with the other door.
3.8.2 Fit the rubber bumpers (N) as shown in Fig.8 to the left hand door.
Parts support is available for this product.
To obtain a parts list and diagram please log on to www.sealey.co.uk, email [e-mail] or phone [phone]