Sealey AP2030BB User manual

INSTRUCTIONS FOR:
HEAVY-DUTY WORKBENCH WITH 5 DRAWERS
BALL BEARING RUNNERS
MODEL :AP2030BB
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
2. CONTENTS AND SPECIFICATION
1.1 GENERAL SAFETY
!WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are
adhered to when using this bench.
"Locate bench in a suitable working area.
"Keep the work area clean, uncluttered and ensure there is adequate lighting.
!WARNING! Use bench on level and solid ground, preferably concrete. Avoid
tarmacadam since the bench may sink into the surface.
"Keep the bench clean and tidy in accordance with good workshop practice.
"Keep children and unauthorised persons away from the working area.
#DO NOT use the bench for any purpose other than that for which it is designed.
#DO NOT exceed maximum capacity of workbench.
#DO NOT undertake work on the bench without the workpiece being adequately
secured. Use clamps or a vice (not included) to secure the workpiece. Available from
your Sealey dealer.
#DO NOT use the bench out of doors.
#DO NOT get the bench wet or use in damp or wet locations or areas where there is
condensation.
#DO NOT clean the bench with any solvents which may damage the paint surface or the
protective coating on the wooden top.
!The maximum load for each drawer is 25kg, full load for the workbench is 250kg.
AP2030BB - 1 - 260407
2.1 Powder coated steel panels with 40mm wood laminate top. Five drawers. Open shelving for storage of larger items. Supplied flat
packed.
2.2 Table Size (W x D): 1372 x 508mm
Working Height: 865mm
Capacity: 250kg
2.3 Carefully unpack the product and check the contents against the diagram below. Should any items be missing or damaged make
immediate contact with your Sealey dealer.
A . . . .SIDE PANEL H . . . .RIGHT SIDE PANEL M . . . . .DRAWER R . . . . .RIGHT SlDE RUNNER
C . . . .BOTTOM RAIL I . . . . .SUPPORT PANEL O . . . . .CORNER BRACE S . . . . .SCREW (M5x12)
D . . . .TOP RAIL J . . . . .BACK PANEL P . . . . .WOODEN TOP T . . . . .ADJUSTABLE LEG LEVELLER
E . . . .CENTRE SUPPORT K . . . .SHELF Q. . . . .LEFT SIDE RUNNER U . . . . .HEX HEAD SCREW 5/8"
G . . . .LEFT SIDE PANEL

3. ASSEMBLY
AP2030BB - 1 - 260407
1
Step 1. As shown in the diagram assemble the two large side panels (A), bottom rail (C) and centre support (E).
STEP 2. Attach the outer slide to the corresponding left/right side panel (G, H). Insert the tabs into the holes in the side panel making sure that
the slider stop fits into the small hole.
Ball bearing runner disassembly: Press the plastic lock spring up or down, and pull the inner
slide out. To put the runners back on, slot the inner slide into the middle slide and push all the
way in.
2

AP2030BB - 1 - 260407
3
STEP 5. Secure the back panels (J) using 8 screws, 4 in each
corner.
STEP 4.Screw the top rails (D) onto the front and back.
45
Step 3. Attach the side panels (G ,H) onto the main unit by screwing them to the front centre support (E) and side panels. Attach support
panels (I) to the side of the unit without sliders.

STEP 6. Turn the workbench upside down and screw in the corner
braces (O) as shown in the diagram. At each corner attach
the leg levellers (T). Slide the workbench top (P) under the
main unit and fix with 4 hex head screws (U)
STEP 7. Attach the inner slides onto the drawers. Slot the
horizontal tab into the hole in the drawer and the vertical
tab into the other hole. Push down until the stop slots
into the small hole.
STEP 8. Pull the middle slide and the ball bearings out as far as possible. Hold the drawer and slot the inner slide on the drawer into the middle slide,
then push the drawer all the way in. take the shelves (K) and slot them into the support panels at the height required.
To remove drawer see Step 2.
66 7
8
AP2030BB - 1 - 260407