Sega MARIO & SONIC AT THE RIO 2016 OLYMPIC GAMES Application guide

IMPORTANT
• Before using this product, read this manual carefully to understand the
contents herein stated.
• After reading this manual, be sure to keep it near the product or in a
convenient place for easy reference when necessary.
OWNER'S & SERVICE MANUAL 420-0025-01UK
MARIO & SONIC at the RIO 2016 OLYMPIC GAMES
Sega Amusements International Limited.
42 Barwell Business Park, Leatherhead Road, Chessington, Surrey, KT9 2NY. United Kingdom.
Telephone: [phone] Facsimile: [phone]
email: [email protected] Web: http://www.segaarcade.com
Sega Corporation
Canal Side Bldg 1-39-9 Higashi-shinagawa Shinagawa-ku, Tokyo, 140-8583, Japan.
Telephone: [phone] Facsimile: [phone]
© SEGA
Errors and omissions excepted (E&OE)
1st PRINTING
March 2016
OWNER’S & SERVICE MANUAL

BEFORE USING THE PRODUCT,BE SURE TO READ THE FOLLOWING:
To maintain safety:
To ensure the safe operation of this product, be sure to read the following before usage.
The following instructions are intended for the users, operators and the personnel in charge of the operation of the
product. After carefully reading and sufciently understanding the warning displays and cautions, handle the product
appropriately. Be sure to keep this manual close to the product or in a convenient place for future reference.
Herein, explanations which require special attention are enclosed with dual lines. Depending on
the potentially hazardous degrees, the terms of DANGER, WARNING, CAUTION, etc. are used. Be sure to
understand the contents of the displays before reading the text.
Indicates that mishandling the product by disregarding this pictograph will
cause severe injury or death.
Indicates that mishandling the product by disregarding this warning will cause a
potentially hazardous situation which can result in death or serious injury.
Indicates that mishandling the product by disregarding this caution will cause a
slight hazardous situation which can
result in personal injury and/or material damage.
For the safe usage of the product, the following pictographs are used:
Indicates "HANDLE WITH CARE." In order to protect the human body and equipment, this display is at-
tached to places where the Owner's Manual, Serviceman Manual and/or Service Manual should be referred
to.
• Perform work in accordance with the instructions herein stated. Instructions for work are explained
by paying attention to the aspect of accident prevention. Failing to perform work as per the instructions
can cause accidents. In the case where only those who have technical expertise should perform the work
to avoid hazardous situation, the instructions herein state that the site maintenance personnel should
perform such work.
• Be sure to turn off the power before working on the machine. To prevent an electric shock, be sure
to turn off the power before carrying out any work that requires direct contact with the interior of the
product. If the work is to be performed in the power-on status, the Instruction Manual herein always states
to that effect.
• Be sure to ground the Earth Terminal. (This is not required in the case where a power cord with earth is
used.)
• This product is equipped with the Earth Terminal. When installing the product, connect the Earth
Terminal to the "accurately grounded indoor earth terminal" by using an earth wire. Unless the product is
grounded appropriately, the user can be subject to an electric shock. After performing repair, etc. for the
control equipment, ensure that the Earth Wire is rmly connected to the control equipment.
• Ensure that the Power Supply used is equipped with an Earth Leakage Breaker. This product does
not incorporate the Earth Leakage Breaker. Using a power supply which is not equipped with the Earth
Leakage Breaker can cause a re when earth leakage occurs.
• Besuretousefuseswhichmeetthespeciedrating. (Only for the machines which use fuses.)
Using fuses exceeding the specied rating can cause a re and an electric shock. (Only for the machines
which use fuses.)Using fuses exceeding the specied rating can cause a re and an electric shock.

• Specification changes (removal of equipment, conversion and addition) not designated by SEGA are
not allowed. The parts of the product include warning labels for safety, covers for personal protection, etc. It
is very hazardous to operate the product by removing parts and/or modifying the circuits. Should doors, lids
and protective parts be damaged or lost, refrain from operating the product, and contact where the product was
purchased from or the ofce herein stated. SEGA shall not be held responsible for any accidents, compensation
for damage to a third party, resulting from the specications not designated by SEGA.
• Ensure that the product meets the requirements of appropriate electrical specications. Before installing the
product, check for electrical specications. SEGA products have a nameplate on which electrical specications
are described. Ensure that the product is compatible with the power supply voltage and frequency requirements
of the location. Using any electrical specications different from the designated specications can cause a re
and an electric shock.
• Install and operate the product in places where appropriate lighting is available, allowing warning labels to be
clearly read. To ensure safety for the customers, labels and printed instructions describing potentially hazardous
situations are applied to places where accidents can be caused. Ensure that where the product is operated has
sufcient lighting allowing the warnings to be read. If any label is peeled off, apply it again immediately. Please
place an order with where the product was purchased from or the ofce herein stated.
• When handling the monitor, be very careful. (Applies only to products with monitors.) Some of the monitor
parts are subject to high tension voltage. Even after turning off the power, some portions are still subject to
high tension voltage sometimes. Monitor repair and replacement should be performed only by those technical
personnel who have knowledge of electricity and technical expertise.
• Be sure to adjust the monitor properly. (Applies only to products with monitors.) Do not operate the product
leaving on-screen ickering or blurring as it is. Using the product with the monitor not properly adjusted may
cause dizziness or a headache to an operator, a player, or the customers.
• When transporting or reselling this product, be sure to attach this manual to the product.
• In the case where commercially available monitors and printers are used in this product, only the contents
relatingtothisproduct areexplainedherein.Somecommercially availableequipmenthasfunctionsand
reactions not stated in this manual. Read this manual together with the specic instruction manual of such
equipment.
• Descriptionshereincontainedmaybesubjecttoimprovementchangeswithoutnotice.
• Thecontentsdescribedhereinarefullypreparedwithduecare.However,shouldanyquestionariseorerrorsbe
found,pleasecontactSEGA.
INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION
Normally, at the time of shipment, SEGA products are in a status allowing for usage immediately after transporting
to the location. Nevertheless, an irregular situation may occur during transportation. Before turning on the power,
check the following points to ensure that the product has been transported in a satisfactory status.
• Are there any dented portions or defects (cuts, etc.) on the external surfaces of the cabinet?
• Are casters and adjusters damaged?
• Do the power supply voltage and frequency requirements meet with those of the location?
• Are all wiring connectors correctly and securely connected? Unless connected in the correct way, connector
connections can not be made accurately. Do not insert connectors forcibly.
• Do power cables have cuts and dents?
• Are all accessories available?
• Can all doors and lids be opened with the accessory keys? Can doors and lids be rmly closed?

iv
LIST OF 3rd PARTY RIGHTS
OpenSSL
_____________________________________________
LICENSE ISSUES
==============
e OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit.
See below for the actual license texts. Actually both licenses are BSD-style Open Source licenses. In case of any license issues related to OpenSSL please contact [email protected]rg.
OpenSSL License Copyright (c) 1998-2011 e OpenSSL Project. All rights reserved.
1. Redistribution and use in source and binary forms, with or without * modication, are permitted provided that the following conditions are met:
2.
3. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
4.
5. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with
the distribution.
6.
7. All advertising materials mentioning features or use of this soware must display the following acknowledgment: “is product includes soware developed by the OpenSSL Project for use
in the OpenSSL Toolkit. (http://www.openssl.org/)”
8.
9. e names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to endorse or promote products derived from this soware without prior written permission. For written permis-
sion, please contact openss[email protected].
10.
11. Products derived from this soware may not be called “OpenSSL” nor may “OpenSSL” appear in their names without prior written permission of the OpenSSL Project.
12.
13. Redistributions of any form whatsoever must retain the following acknowledgment: “is product includes soware developed by the OpenSSL Project for use in the OpenSSL Toolkit
(http://www.openssl.org/)”
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ``AS IS’’ AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WAR-
RANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEM-
PLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
is product includes cryptographic soware written by Eric Young (eay@cryptso.com). is product includes soware written by Tim Hudson (tjh@cryptso.com).
Original SSLeay License
Copyright (C) 1995-1998 Eric Young (eay@cryptso.com) All rights reserved.
is package is an SSL implementation written by Eric Young (eay@cryptso.com).
e implementation was written so as to conform with Netscapes SSL.
is library is free for commercial and non-commercial use as long as the following conditions are aheared to. e following conditions apply to all code found in this distribution, be it the RC4,
RSA, lhash, DES, etc., code; not just the SSL code. e SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson (tjh@
cryptso.com). Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric Young should be given attribution
as the author of the parts of the library used. is can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package. Redistribution
and use in source and binary forms, with or without modication, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with
the distribution.
3. All advertising materials mentioning features or use of this soware must display the following acknowledgement: “is product includes cryptographic soware written by Eric Young
(eay@cryptso.com)” e word ‘cryptographic’ can be le out if the rouines from the library being used are not cryptographic related :-).
4. If you include any Windows specic code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement: “is product includes soware
written by Tim Hudson (tjh@cryptso.com)”
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS’’ AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE MPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
e licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution licence
[including the GNU Public Licence.]
is product includes soware developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)
is product includes cryptographic soware written by Eric Young (eay@cryptso.com).

LIST OF 3rd PARTY RIGHTS
v
PicoJSON
_____________________________________________
Copyright 2009-2010 Cybozu Labs, Inc. Copyright 2011-2014 Kazuho Oku All rights reserved.
Redistribution and use in source and binary forms, with or without modication, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with
the distribution.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER
OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Putty
_____________________________________________
PuTTY is copyright 1997-2010 Simon Tatham. Portions copyright Robert de Bath, Joris van Rantwijk, Delian Delchev, Andreas Schultz, Jeroen Massar, Wez Furlong, Nicolas Barry, Justin Brad-
ford, Ben Harris, Malcolm Smith, Ahmad Khalifa, Markus Kuhn, Colin Watson, and CORE SDI S.A.
Permission is hereby granted, free of charge, to any person obtaining a copy of this soware and associated documentation les (the “Soware”), to deal in the Soware without restriction, includ-
ing without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Soware, and to permit persons to whom the Soware is furnished to do so,
subject to the following conditions:
e above copyright notice and this permission notice shall be included in all copies or substantial portions of the Soware.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANT-
ABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL SIMON TATHAM BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
DEALINGS IN THE SOFTWARE.
libcurl
_____________________________________________
COPYRIGHT AND PERMISSION NOTICE
Copyright (c) 1996 - 2015, Daniel Stenberg, [email protected]. All rights reserved.
Permission to use, copy, modify, and distribute this soware for any purpose with or without fee is hereby granted, provided that the above copyright notice and this permission notice appear in all
copies.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANT-
ABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF THIRD PARTY RIGHTS. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE
LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION
WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
Except as contained in this notice, the name of a copyright holder shall not be used in advertising or otherwise
MessagePack
_____________________________________________
Apache License Version 2.0, January 2004 http://www.apache.org/licenses/
TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION
Denitions. “License” shall mean the terms and conditions for use, reproduction, and distribution as dened by Sections 1 through 9 of this document. “Licensor” shall mean the copyright owner or
entity authorized by the copyright owner that is granting the License. “Legal Entity” shall mean the union of the acting entity and all other entities that control, are controlled by, or are under common
control with that entity. For the purposes of this denition, “control” means (i) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or
(ii) ownership of y percent (50%) or more of the outstanding shares, or (iii) benecial ownership of such entity. “You” (or “Your”) shall mean an individual or Legal Entity exercising permissions
granted by this License. “Source” form shall mean the preferred form for making modications, including but not limited to soware source code, documentation
source, and conguration les. “Object” form shall mean any form resulting from mechanical
transformation or translation of a Source form, including but not limited to compiled object code, generated documentation, and conversions to other media types. “Work” shall mean the work of
authorship, whether in Source or Object form, made available under the License, as indicated by a
copyright notice that is included in or attached to the work (an example is provided in the Appendix below). “Derivative Works” shall mean any work, whether in Source or Object form, that is based
on (or derived from) the Work and for which the editorial revisions, annotations, elaborations, or other modications represent, as a whole, an original work of authorship. For the purposes of this
License, Derivative Works shall not include works that remain separable from, or merely link (or bind by name) to the interfaces of, the Work and Derivative Works thereof.
“Contribution” shall mean any work of authorship, including the original version of the Work and any modications or additions to that Work or Derivative Works thereof, that is intentionally
submitted to Licensor for inclusion in the Work by the copyright owner or by an individual or Legal Entity authorized to submit on behalf of
the copyright owner. For the purposes of this denition, “submitted” means any form of electronic, verbal, or written communication sent to the Licensor or its representatives, including but not
limited to communication on electronic mailing lists, source code control systems, and issue tracking systems that are managed by, or on behalf of, the Licensor for the purpose of discussing and
improving the Work, but excluding communication that is conspicuously marked or otherwise designated in writing by the copyright owner as “Not a Contribution.” “Contributor” shall mean
Licensor and any individual or Legal Entity on behalf of whom a Contribution has been received by Licensor and subsequently incorporated within the Work.
Grant of Copyright License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable
copyright license to reproduce, prepare Derivative Works of, publicly display, publicly perform, sublicense, and distribute the Work and such Derivative Works in Source or Object form.
Grant of Patent License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable
(except as stated in this section) patent license to make, have made, use, oer to sell, sell, import, and otherwise transfer the Work, where such license applies only to those patent claims licensable
by such Contributor that are necessarily infringed by their Contribution(s) alone or by combination of their Contribution(s) with the Work to which such Contribution(s) was submitted. If You
institute patent litigation against any entity (including a cross-claim or counterclaim in a lawsuit) alleging that the Work or a Contribution incorporated within the Work constitutes direct or con-
tributory patent infringement, then any patent licenses granted to You under this License for that Work shall terminate as of the date such litigation is led. 4. Redistribution. You may reproduce
and distribute copies of the Work or Derivative Works thereof in any medium, with or without modications, and in Source or Object form, provided that You meet the following conditions: (a)
You must give any other recipients of the Work or Derivative Works a copy of this License; and (b) You must cause any modied les to carry prominent notices stating that You changed the les;
and (c) You must retain, in the Source form of any Derivative Works that You distribute, all copyright, patent, trademark, and attribution notices from the Source form of the Work, excluding those
notices that do not pertain to any part of the Derivative Works; and (d) If the Work includes a “NOTICE” text le as part of its
distribution, then any Derivative Works that You distribute must include a readable copy of the attribution notices contained within such NOTICE le, excluding those notices that do not
pertain to any part of the Derivative Works, in at least one of the following places: within a NOTICE text le distributed as part of the Derivative Works; within the Source form or documentation,
if provided along with the Derivative Works; or, within a display generated by the Derivative Works, if and wherever such third-party notices normally appear. e contents of the NOTICE le
are for informational purposes only and do not modify the License. You may add Your own attribution notices within Derivative Works that You distribute, alongside or as an addendum to the
NOTICE text from the Work, provided that such additional attribution notices cannot be construed as modifying the License. You may add Your own copyright statement to Your modications
and may provide additional or dierent license terms and conditions for use, reproduction, or distribution of Your modications, or for any such Derivative Works as a whole, provided Your use,
reproduction, and distribution of the Work otherwise complies with the conditions stated in this License.
5. Submission of Contributions. Unless You explicitly state otherwise, any Contribution intentionally submitted for inclusion in the Work by You to the Licensor shall be under the terms and
conditions of this License, without any additional terms or conditions. 41 Notwithstanding the above, nothing herein shall supersede or modify the terms of any separate license agreement you
may have executed with Licensor regarding such Contributions.
6. Trademarks. is License does not grant permission to use the trade names, trademarks, service marks, or product names of the Licensor, except as required for reasonable and customary use in
describing the origin of the Work and reproducing the content of the NOTICE le.
7. Disclaimer of Warranty. Unless required by applicable law or agreed to in writing, Licensor provides the Work (and each Contributor provides its Contributions) on an “AS IS” BASIS, WITH

vi
LIST OF 3rd PARTY RIGHTS
OUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied, including, without limitation, any warranties or conditions of TITLE, NON-INFRINGEMENT, MERCHANT-
ABILITY, or FITNESS FOR A PARTICULAR PURPOSE. You are solely responsible for determining the appropriateness of using or redistributing the Work and assume any risks associated with
Your exercise of permissions under this License.
8. Limitation of Liability. In no event and under no legal theory, whether in tort (including negligence), contract, or otherwise, unless required by applicable law (such as deliberate and grossly
negligent acts) or agreed to in writing, shall any Contributor be liable to You for damages, including any direct, indirect, special, incidental, or consequential damages of any character arising as a
result of this License or out of the use or inability to use the Work (including but not limited to damages for loss of goodwill, work stoppage, computer failure or malfunction, or any and all
other commercial damages or losses), even if such Contributor has been advised of the possibility of such damages.
9. Accepting Warranty or Additional Liability. While redistributing the Work or Derivative Works thereof, You may choose to oer, and charge a fee for, acceptance of support, warranty, indemnity,
or other liability obligations and/or rights consistent with this License. However, in accepting such obligations, You may act only on Your own behalf and on Your sole responsibility, not on behalf
of any other Contributor, and only if You agree to indemnify, defend, and hold each Contributor harmless for any liability incurred by, or claims asserted against, such Contributor by reason
of your accepting any such warranty or additional liability.
END OF TERMS AND CONDITIONS
APPENDIX: How to apply the Apache License to your work. To apply the Apache License to your work, attach the following boilerplate notice, with the elds enclosed by brackets “[]” replaced
with your own identifying information. (Don’t include the brackets!) e text should be enclosed in the appropriate comment syntax for the le format. We also recommend that a le or class
name and description of purpose be included on the same “printed page” as the copyright notice for easier identication within third-party archives. Copyright [yyyy] [name of copyright owner]
Licensed under the Apache License, Version 2.0 (the “License”); you may not use this le except in compliance with the License. You may obtain a copy of the License at http://www.apache.org/
licenses/LICENSE-2.0 Unless required by applicable law or agreed to in writing, soware distributed under the License is distributed on an “AS IS” BASIS, WITHOUT WARRANTIES OR CON-
DITIONS OF ANY KIND, either express or implied. See the License for the specic language governing permissions and limitations under the License.
avr-libc
_____________________________________________
Portions of avr-libc are Copyright (c) 1999-2008 Werner Boellmann, Dean Camera, Pieter Conradie, Brian Dean, Keith Gudger, Wouter van Gulik, Bjoern Haase, Steinar Haugen, Peter Jansen,
Reinhard Jessich, Magnus Johansson, Harald Kipp, Carlos Lamas, Cli Lawson, Artur Lipowski, Marek Michalkiewicz, Todd C. Miller, Rich Neswold, Colin O’Flynn, Bob Paddock, Andrey
Pashchenko, Reiner Patommel, Florin-Viorel Petrov, Alexander Popov, Michael Rickman, eodore A. Roth, Juergen Schilling, Philip Soeberg, Anatoly Sokolov, Nils Kristian Strom, Michael
Stumpf, Stefan Swanepoel, Helmut Wallner, Eric B. Weddington, Joerg Wunsch, Dmitry Xmelkov, Atmel Corporation, egnite Soware GmbH, e Regents of the University of California. All
rights reserved.
1. Redistribution and use in source and binary forms, with or without modication, are permitted provided that the following conditions are met:
2. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
3. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the
distribution.
Neither the name of the copyright holders nor the names of contributors may be used to endorse or promote products derived from this soware without specic prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER
OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

INTRODUCTION
vii
INTRODUCTION
This manual is intended to provide detailed descriptions together with all necessary information covering the general
operation of electronic assemblies, electromechanical, servicing control, spare parts, etc. for the product,
"MARIO & SONIC AT THE RIO 2016 OLYMPIC GAMES ARCADE EDITION"
This manual is intended for the owners, personnel managers in charge of operation of this product.
Operate the product after carefully reading and sufciently understanding the instructions.
In the unlikely event that the product does not function correctly, DO NOT allow anyone other than a technician to
touch the internal system. Turn off the power to the machine, making sure to unplug the electrical cord from the out-
let, and contact the ofce listed below or the point-of-purchase for this product.
Use of this product is unlikely to cause physical injuries or damage to property. However, points that require special
attention are indicated by bold text, the words "STOP, IMPORTANT or CAUTION” and the symbols below.
Indicates important information that, if ignored, may result in the mishandling
of the product and cause faulty operation or damage to the product.
Indicates a warning or caution that, if ignored, may result in the mishandling
of the product and cause faulty operation or damage to the product.
Sega Amusements International Limited.
42 Barwell Business Park, Leatherhead Road, Chessington, Surrey, KT9 2NY. United Kingdom.
International Sales: [phone] Facsimile: [phone]
email: [email protected] Web: http://www.segaarcade.com
Sega Corporation
Canal Side Bldg 1-39-9 Higashishinagawa Shinagawa-ku, Tokyo, 140-8583, Japan.
Telephone: [phone] Facsimile: [phone]
Sega Total Solutions
42 Barwell Business Park, Leatherhead Road, Chessington, Surrey, KT9 2NY. United Kingdom.
Parts & Service: [phone] Facsimile: [phone]
Play It! Amusements, inc.
252 Beinoris Drive, Wood Dale, IL. 60191, USA
Parts & Service: +00 (1) 224 265 4287

viii
INTRODUCTION
Parts replacement, maintenance inspections and troubleshooting should be carried out by site maintenance personnel
or other qualied professionals. This manual includes directions for potentially dangerous procedures which should
only be carried out by professionals with the appropriate specialised knowledge.
The site maintenance personnel or other qualied professionals mentioned in this manual are dened as follows:
Site maintenance personnel:
Individuals with experience in maintaining amusement equipment, vending machines, etc., working under the super-
vision of the owner/operator of this product to maintain machines within amusement facilities or similar premises by
carrying out everyday procedures such as assembly, maintenance inspections, and replacement of units/expendable
parts.
Activities to be carried out by site maintenance personnel:
Amusement equipment/vending machine assembly, maintenance inspection and replacement of units/expendable
parts.
Other qualied professionals:
Persons employed by amusement equipment manufacturers, or involved in design, production, testing or mainte-
nance of amusement equipment. The individual should have either graduated from technical school or hold similar
qualications in electrical/electronics/mechanical engineering.
Activities to be carried out by other qualied professionals:
Amusement equipment/vending machine assembly, repair/adjustment of electrical/electronic/mechanical parts.
Denition of 'Site Maintenance Personnel or Other Qualied Individuals
Servicing and maintenance work of the contents herein stated should be
performed by the SERVICEMAN stipulated as per IEC Standard. Those who do not
have technical expertise and knowledge other than the SERVICEMAN are not
allowed to perform the work herein stated. Executing aforementioned work by
such non-technical personnel can cause serious accidents that may endanger life.

INTRODUCTION
ix
Electrical & Mechanical Specications
Individual Dimensions
Cabinet: 1.23m (48.4in) [width] x 0.89m (35.1in) [depth]
1.93m (76.0in) [height]
Billboard: 1.21m (47.6in) [width] x 0.49m (19.3in) [depth]
0.44m (17.3in) [height]
Floor Plate: 0.86m (33.9in) [width] x 0.80m (31.5in) [depth]
0.90m (45.4in) [height]
Assembled Dimensions: 1.23m (48.4in) [width] x 1.47m (57.9in) [depth]
2.27m (89.3in) [height]
Weights
Cabinet (Inc Billboard): 262kg (577.6lb.)
Floor: 54kg (119lb.)
Total Weight: 316kg (697 lb)
Electrical Consumption
Operating Voltage: AC240V
Current: 1.4A [336W]
Operating Voltage: AC120V
Current: 2.6A [624W]
SPECIFICATIONS
2.27m
1.23m 1.47m

x
INTRODUCTION
Waste of Electrical and Electronic Equipment (WEEE) Statement.
Waste of Electrical and Electronic Equipment (WEEE) Statement.
The WEEE (Waste of Electrical and Electronic Equipment) directive places an obligation on all EU based
manufacturers and importers of Electrical and Electronic Equipment (EEE) to ensure waste equipment is disposed of
in accordance with the directive at the end of their useful life.
The symbol shown below will be placed on all products manufactured from 13th August 2005, which indicates this
product must NOT be disposed of with other normal waste. Upon purchasing any EEE from SEGA Amusements
International Ltd. The user accepts responsibility to dispose of their waste equipment by arranging to return it to a
designated UK collection point (AATF) or an Approved Exporter (AE) for the correct recycling of waste electrical
and electronic equipment.
For more information on Approved Authorised Treatment Facilities (AATF) within the UK please consult the
government website www.gov.uk
For users outside of the UK EEE should be disposed of in accordance with the local policy on the recycling of Waste
Electrical and Electronic Equipment.
Battery Recycling Statement.
The EC Directive on Batteries and Accumulators (2006/66/EC) aims to minimise the impact of batteries on the
environment and encourage the recovery of the materials they contain. To achieve increased collection and recycling
of waste batteries, the Directive places ‘producer responsibility’ obligations on manufacturers and importers of
portable, industrial and automotive batteries.
The symbol shown below will be on all equipment tted with batteries from 26th September 2008 and indicates they
must NOT be disposed of with other normal waste. Instead, it is the user’s responsibility to dispose of used batteries
by arranging to return them to a designated collection point for the correct recycling.
For more information about where you can send your waste batteries for recycling contact your local authority
ofce.
REGISTERED IN ENGLAND REGISTERED NO. 1711515
REGISTERED OFFICE: BLOCK C 42 BARWELL BUSINESS PARK, CHESSINGTON, SURREY KT9 2NY

xi
420-0016UK
TABLE OF CONTENTS
INTRODUCTION vii
1HANDLING PRECAUTIONS 1
2 PRECAUTIONS REGARDING INSTALLATION LOCATION 5
2-1 LIMITATIONS OF USAGE 6
2-2 OPERATION AREA 7
3 PRECAUTIONS REGARDING PRODUCT OPERATION 9
3-1 BEFORE OPERATION 9
3-2 DURING OPERATION (PAYING ATTENTION TO CUSTOMERS) 11
4PART DESCRIPTIONS 13
5ACCESSORIES 14
6 ASSEMBLY AND INSTALLATION 15
6-1 INSTALLING THE CABINET 19
6-2 INSTALLING THE BILLBOARD 20
6-3 ASSEMBLING THE FLOOR 23
6-4 INSTALLING THE FLOOR TO THE CABINET 27
6-5 INSPECT FIXATION TO SITE 31
6-6 POWER SUPPLY AND OTHER CONNECTIONS 32
6-7 COMMUNICATION / NETWORK CONNECTIONS 34
6-8 TURNING ON THE POWER 36
6-9 CONFIRMATION OF ASSEMBLY 37
6-10APPLYING WARNING LABELS (EPILEPTIFORM SEIZURES) 38
7PRECAUTIONS WHEN MOVING THE MACHINE 39
8GAME DESCRIPTION 43
8-1 GAME SUMMARY 43
8-2 HOW TO CONTROL THE GAME 43
8-3 GAME FLOW 44

xii
9EXPLANATION OF TEST AND DATA DISPLAY 45
9-1 SWITCH UNIT AND COIN METER. 46
9-2 TEST MENU 46
9-3 GAME TEST MENU 47
9-4 BOOKKEEPING 48
9-5 INPUT TEST 50
9-6 OUTPUT TEST 51
9-7 GAME & COIN ASSIGNMENTS 52
9-8 LED BOARD INFORMATION 53
9-9 NETWORK TEST 54
9-10 BACKUP DATA CLEAR 55
10 CONTROLLER UNIT(S), SWITCHES AND BUTTONS 56
10-1 REPLACING THE LEVER BUTTON 57
10-2 REPLACING THE LEVER 59
11 VIDEO DISPLAY 64
11-1 GENERAL DESCRIPTION 64
11-2 CLEANING THE SCREEN 65
11-3 ON SCREEN ADJUSTMENT METHOD (OSD) 66
12 COIN HANDLING 72
12-1 CLEANING THE COIN SELECTOR 72
12-2 FAULT FINDING 75
12-3 ADJUSTING THE PRICE OF PLAY (EXCEL) 76
12-4 QUICK VIEW COMMON COIN SETTINGS (USA) 77
12-5 ADJUSTING THE PRICE COMMON SETTINGS 78
12-5 UNIVERSAL CARD LINK (UCL) 82
13 ACTIVE FLOOR ASSY 83
13-1 CLEANING THE JUMP SENSOR WINDOWS 83
13-2 CLEANING THE FLOOR MAT 84
13-3 REPLACING THE FLOOR MAT 85
13-4 REPLACING THE FLOOR FOOT SENSORS 88
13-5 REPLACING THE JUMP SENSORS 90
14 PERIODIC INSPECTION 93
15 TROUBLESHOOTING 96
15-1 TROUBLESHOOTING (WHEN NO ERROR MESSAGE IS SHOWN) 96
16 GAME BOARD (Nu1.1) 99
16-1HANDLING PRECAUTIONS 100
16-2 GAME BOARD (Nu1.1) - LOCATION & REMOVAL 101
16-3Nu1.1 CLEANING 104
16-3 REPLACING Nu 1.1 GAME BD 106
16-3 SYSTEM TEST MODE 107
16-3-1 SYSTEM INFORMATION 109

xiii
16-3-2 STORAGE INFORMATION 111
16-3-3 JVS TEST 113
16-3-4 MONITOR TEST 116
16-3-5 SPEAKER TEST 117
16-3-6 COIN ASSIGNMENTS 118
16-3-7 CLOCK SETTINGS 124
16-3-8 NETWORK SETTINGS 126
17 DESIGN-RELATED PARTS 130
18 PARTS LIST 131
19 PARTS & SERVICE CONTACT INFORMATION 154
20 WIRE COLOUR CODE TABLE 155
21 WIRING DIAGRAMS 156

HANDLING PRECAUTIONS
1
1
1HANDLING PRECAUTIONS
When installing or inspecting the machine, be very careful of the following points and pay attention to ensure that
the player can enjoy the game safely.
Non-compliance with the following points or inappropriate handling running counter to the cautionary matters
herein stated can cause personal injury or damage to the machine.
Before performing work, be sure to turn the power off. Performing the work
without turning the power off can cause an electric shock or short circuit.
In cases where work should be performed in the status of power on, this
manual always states to that effect.
To avoid an electric shock or short circuit, do not plug in or unplug quickly.
To avoid an electric shock, do not plug in or unplug with a wet hand.
Do not expose power cords or earth wires on the surface, (oor, passage,
etc.) If exposed, the power cords and earth wires are susceptible to
damage. Damaged cords and wires can cause an electric shock or short
circuit.
To avoid causing a fire or an electric shock, do not put things on or
damage the power cords.
When or after installing the product, do not unnecessarily pull the power
cord. If damaged, the power cord can cause a re or an electric shock.
In case the power cord is damaged, ask for a replacement through where
the product was purchased from or the ofce herein stated. Using the cord
as is damaged can cause re, an electric shock or leakage.
This product MUST be Earthed. Inappropriate Earthing can cause an
electric shock.
Be sure to use fuses meeting the specied rating. Using fuses exceeding
the specied rating can cause a re or an electric shock.
Be sure that connections such as IC BD are made properly. Insufficient
insertion can cause an electric shock.
Specication changes, removal of equipment, conversion and/or addition,
not designated by SEGA are not permitted.
Failure to observe this may cause a fire or an electric shock. Non-
compliance with this instruction can have a bad inuence upon physical
conditions of the players or the onlookers, or result in injury during play.
SEGA shall not be held responsible for damage, compensation for damage
to a third party, caused by specication changes not designated by SEGA.
Do not perform any work or change parts not listed in this manual. Doing
so may lead to an accident.
If you need to perform any work not listed in this manual, request work
from the ofce indicated in this manual or the point of purchase, or inquires
for details.
Be sure to perform periodic maintenance inspections herein stated.

2
HANDLING PRECAUTIONS
1
For the IC board circuit inspections, only the use of a logic tester is
recommended. Using a Multi Tester or General Purpose Tester may result in
damage to IC Circuits. Static electricity from your body may damage some
electronics devices on the IC board. Before handling the IC board, touch a
grounded metallic surface so that the static electricity can be discharged.
Some parts are not designed and manufactured specifically for this game
machine. The manufacturers may discontinue, or change the specications of
such general-purpose parts. If this is the case, SEGA cannot repair or replace
a failed game machine whether or not a warranty period has expired.
CONCERNING THE STICKER DISPLAY
This SEGA product has stickers attached describing the product manufacture No. (Serial No.) and Electrical
Specications. It also has a Sticker describing where to contact for repair and for purchasing parts.
When inquiring about or asking for repairs, mention the Serial No. and Name of Machine indicated on the Sticker.
The Serial Number indicates the product register. Identical machines could have different parts depending on the
date of production. Also, improvements and modifications might have been made after the publication of this
manual. In order to ensure you order the correct parts, mention the Serial No. when contacting the applicable places.
CONCERNING WARNING DISPLAYS
This SEGA product has warning displays on stickers, labels and/or printed instructions adhered/attached to or
incorporated in the places where a potentially hazardous situation could arise. The warning displays are intended
for accident prevention for customers and for avoiding hazardous situations relating to maintenance and servicing
work. Some portions of the cabinet contain high voltage and may cause accidents if touched. When performing
maintenance, be very careful of the warning displays. It is especially important that any complex repair and
replacement work not mentioned herein should be performed by those technical personnel who have knowledge of
electricity and technical expertise.
In order to prevent accidents, caution any customer ignoring the warnings to cease and desist immediately.
VIDEO GAME-INDUCED SEIZURES (VGS) AND PHOTOSENSETIVE EPILEPSY (PSE)
This SEGA product has warning displays on stickers which outline the risk of epilepticform and photosensetive
seizures. These warning displays on stickers are applied close in proximity of the device which may promote
symptoms of either video game-induced seizures or epilepsy. The warning displays are supplied in several languages
and form part of the Installation kit supllied with this product. It is standard practice for the English version of this
label to be applied during manufacture, however it is especially important for the operator to apply the same said
label in the lanuguage of the country of operation.

HANDLING PRECAUTIONS
3
1
STICKER DISPLAY
P.A.T. Label
Inside
Inside
Inside
Inside
Inside
Inside
Rating Label
Serial No Label
WEEE Label
440-DS0010UK
Danger Sticker - High Voltage
440-CS0186-01UK
Epilepsy Sticker
440-WS0010UK
Warning Sticker - High Voltage
440-WS0010UK
Warning Sticker - High Voltage
440-DS0010UK
Danger Sticker - High Voltage
LB1101
Caution Sticker - Battery replacement
440-CS0010UK
Caution Sticker
440-CS0010UK
Caution Sticker
440-CS0010UK
Caution Sticker

4
HANDLING PRECAUTIONS
1
To avoid injury, please
do not play this game if
you have or suffer from
any one of these
conditions:
•If you have high blood
pressure or heart
condition.
•If you are intoxicated
or under the influence
of drugs.
•If you are pregnant.
Always wear footwear
when playing this
game.
Do not play this game
when wearing high
heeled shoes.
Only one person is
allowed to play on this
machine at one time.
440-CS0019UK
Caution Sticker - Player Caution
LB1212B
Bulb Rating - DC12V/1.2W
440-CS0021UK
CAUTION - Place Objects
Do not place objects
on the floor during
gameplay
BULB
DC12V
1.2W

PRECAUTIONS REGARDING INSTALLATION LOCATION
5
2
2 PRECAUTIONS REGARDING INSTALLATION LOCATION
This product is an indoor game machine. Do not install it outside. Even indoors,
avoid installing in places mentioned below so as not to cause a fire, electric
shock, injury and/or malfunction.
Places subject to rain or water leakage, or places subject to high humidity in the
proximity of an indoor swimming pool and/or shower, etc.
Places subject to direct sunlight, or places subject to high temperatures in the
proximity of heating units, etc.
Places filled with inflammable gas or vicinity of highly inflammable/volatile
chemicals or hazardous matter.
Dusty places.
Sloped surfaces.
Places subject to any type of violent impact.
Vicinity of anti-disaster facilities such as re exits and re extinguishers.
Areas where the temperature exceeds the applicable temperature (ambient
temperature) range of 5 to 30 degrees centigrade.
Securing a safe area for operation as described in this manual will ensure
safe operation for players and observers.
SEGA shall not be held responsible for damage or compensation for damage
to a third party, resulting from the failure to observe this instruction.

6
PRECAUTIONS REGARDING INSTALLATION LOCATION
2
Be sure to check the Electrical Specifications. Ensure that this product
is compatible with the location's power supply, voltage, and frequency
requirements. A label describing Electrical Specifications is attached to the
product. Non-compliance with the Electrical Specications can cause a re and
electric shock.
This product requires a breaker and earth mechanism as part of the location
facilities. Using the product without these can cause a re and electric shock.
Ensure that the indoor wiring for the power supply is rated at 15 A or higher (AC
single phase 100 V ~ 120 V area), and 7 A or higher (AC 220 V ~ 240 V area). Non-
compliance with the Electrical Specications can cause a re and electric shock.
Be sure to use an independent power supply equipped with an earth leakage
breaker. Using a power supply without an earth leakage breaker can cause an
outbreak of re if a power surge occurs.
Putting many loads on one electrical outlet can cause generation of heat and a
re resulting from overload.
When using an extension cord, ensure that the cord is rated at 15 A or higher (AC
100 V ~ 120 V area) and 7 A or higher (AC 220 V ~ 240 V area). Using a cord rated
lower than the specied rating can cause a re and electric shock.
2-1 LIMITATIONS OF USAGE

PRECAUTIONS REGARDING INSTALLATION LOCATION
7
2
To install this product, the entrance must be at least 0.9m in width and 1.94m
in height.
Do not attempt to move the product by pushing or pulling on the plastic
parts. This may damage the product and my cause personal injury.
• For the operation of a 2 player machine, secure a minimum area of 2.17m
(W) x 2.97m (D). These dimensions are necessary to enable the customer
to walk around the machine and also to provide adequate ventilation. The
player is required to be physically active when playing this game, so there is
a possibility of a player falling, so be sure to secure the minimum area around
the machine specied in this manual.
• Be sure to provide sufficient space specified in this manual. Do not allow
objects to block the ventilation ports. It can cause generation of heat which in
turn may cause a re hazard.
• SEGA shall not be held responsible for damage or compensation for damage
to a third party, resulting from the failure to observe this instruction.
• If the machine does not t through the entryway to the installation location,
do not disassemble it without first consulting the instructions. The machine
should only be disassembled in accordance with the instructions listed in
this manual; do not attempt to disassemble it in any other way. Specic tools
and adjustment procedures are required to assemble and disassemble the
mechanical parts. Attempting to assemble or disassemble the machine
without consulting the instructions may result in accidents during assembly/
disassembly and electric shock, short circuits, and/or personal injury during
operation. If the machine still does not t through the entryway after following
the procedures in this manual, contact your retailer or the ofce listed in this
manual.
• If the machine is still too large to t through the entryway after following the
procedures listed in this manual, do not tip the machine on its side. Attempting
to transport the machine while it is tipped on its side may cause accidents. It
may also damage or warp parts of the machine, resulting in accidents during
operation.
• To install this product, the entrance must be at least 0.9 m in width and 1.94m
in height. If the entrance is too narrow, do not tilt the product carelessly. If
all the product weight is put on the casters at one side only, there could be
damage or deformation, causing serious accidents such as workers getting
caught underneath.
2-2 OPERATION AREA