Sega TARGET BRAVO OPERATION GHOST User manual

IMPORTANT
• Before using this product, read this manual carefully to understand the
contents herein stated.
• After reading this manual, be sure to keep it near the product or in a
convenient place for easy reference when necessary.
OWNER'S MANUALOPERATION GHOST 420-0029-00UK
Sega Amusements International Limited.
42 Barwell Business Park, Leatherhead Road, Chessington, Surrey, KT9 2NY. United Kingdom.
Telephone: [phone] Facsimile: [phone]
email: [email protected] Web: http://www.segaarcade.com
© SEGA
Errors & Omissions Excepted (E&OE)
420-0029-00UK
1st PRINTING

BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING:
To maintain safety:
To ensure the safe operation of this product, be sure to read the following before usage:
The following instructions are intended for the users, operators and the personnel in charge of the
operation of the product. After carefully reading and suciently understanding the warning displays
and cautions, handle the product appropriately. Be sure to keep this manual close to the product or
in a convenient place for future reference.
Herein, explanations which require special attention are enclosed with dual lines. Depending on
the potentially hazardous degrees, the terms of DANGER, WARNING, CAUTION, etc. are used.
Be sure to understand the contents of the displays before reading the text.
Indicates that mishandling the product by disregarding this pictograph will
cause severe injury or death.
Indicates that mishandling the product by disregarding this warning will cause
a potentially hazardous situation which can result in death or serious injury.
Indicates that mishandling the product by disregarding this caution will cause
a slight hazardous situation which can result in personal injury and/or material
damage.
For the safe usage of the product, the following pictographs are used:
Indicates "HANDLE WITH CARE". In order to protect the human body and equipment,
this display is attached to places where the instruction manual should be referred to.
Indicates a "protective earth terminal". Before operating the equipment, be sure to connect
it to the ground (this step may be omitted for products in which a power cable with earth is
used).
• Perform work in accordance with the instructions herein stated.
Instructions for work are explained by paying attention to the aspect of accident prevention.
Failing to perform work as per the instructions can cause accidents. In the case where only
those who have technical expertise should perform the work to avoid hazardous situation, the
instructions herein state that the site maintenance personnel should perform such work.
• Besuretoturno󰀨thepowerbeforeworkingonthemachine.
To prevent an electric shock, be sure to turn o the power and unplug the power cable before
carrying out any work that requires direct contact with the interior of the product. If the work is
to be performed in the power-on status, the instruction manual herein always states to that eect.
• Besuretogroundtheearthterminal(thisisnotrequiredinthecasewherea
powercablewithearthisused).
This product is equipped with the earth terminal. When installing the product, connect the earth
terminal to the "accurately grounded indoor earth terminal" by using an earth wire. Unless the
product is grounded appropriately, the user can be subject to an electric shock. After performing
repair, etc. for the control equipment, ensure that the earth wire is rmly connected to the control
equipment.
• Ensurethatthepowersupplyusedisequippedwithanearthleakagebreaker.
Using a power supply which is not equipped with the earth leakage breaker can cause a re when
earth leakage occurs.
• Besuretousefuseswhichmeetthespeciedrating(onlyforthemachineswhich
usefuses).
Using fuses exceeding the specied rating can cause a re and an electric shock.

• Specicationchanges(removalofequipment,conversionsandadditions)not
designatedbySEGAarenotallowed.
The parts of the product include warning labels for safety, covers for personal protection, etc. It
is very hazardous to operate the product by removing parts and/or modifying the circuits. Should
doors, lids and protective parts be damaged or lost, refrain from operating the product, and
contact where the product was purchased from or the oce herein stated.
SEGA shall not be held responsible for any accidents, compensation for damage to a third party,
resulting from the specications not designated by SEGA.
• Ensurethattheproductmeetstherequirementsofappropriateelectrical
specications.
Before installing the product, check for electrical specications. SEGA products have a
nameplate on which electrical specications are described. Ensure that the product is compatible
with the power supply voltage and frequency requirements of the location. Using any electrical
specications dierent from the designated specications can cause a re and an electric shock.
• Installandoperatetheproductinplaceswhereappropriatelightingisavailable,
allowingwarninglabelstobeclearlyread.
To ensure safety for the customers, labels and printed instructions describing potentially
hazardous situations are applied to places where accidents can be caused. Ensure that where the
product is operated has sucient lighting allowing the warnings to be read. If any label is peeled
o, apply it again immediately. Please place an order with where the product was purchased from
or the oce herein stated.
• Whenhandlingthemonitor,beverycareful(appliesonlytoproductswith
monitors).
Some of the monitor parts are subject to high tension voltage. Even after turning o the power,
some portions are still subject to high tension voltage. Monitor repair and replacement should
be performed only by those technical personnel who have knowledge of electricity and technical
expertise.
• Besuretoadjustthemonitorproperly(appliesonlytoproductswithmonitors).
Do not operate the product leaving on-screen ickering or blurring as it is. Using the product
with the monitor not properly adjusted may cause dizziness or a headache to an operator, a
player, or customer.
• Whentransportingorresellingthisproduct,besuretoattachthismanualtothe
product.
* In the case where commercially available monitors and printers are used in this product, only the
contents relating to this product are explained herein. Some commercially available equipment
has functions and reactions not stated in this manual. Read this manual together with the specic
instruction manual of such equipment.
* Descriptions herein contained may be subject to improvement changes without notice.
* The contents described herein are fully prepared with due care. However, should any question
arise or errors be found, please contact SEGA.
INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION
Normally, at the time of shipment, SEGA products are in a status allowing for usage immediately
after transporting to the location. Nevertheless, an irregular situation may occur during
transportation. Before turning on the power, check the following points to ensure that the product
has been transported in a satisfactory status:
Are there any dented portions or defects (cuts, etc.) on the external surfaces of the cabinet?
Are casters and adjusters damaged?
Do the power supply voltage and frequency requirements meet with those of the location?
Are all wiring connectors correctly and securely connected? Unless connected in the correct way,
connector connections can not be made accurately. Do not insert connectors forcibly.
Do power cables have cuts and dents?
Are all accessories available?
Can all doors and lids be opened with the accessory keys? Can doors and lids be rmly closed?

INTRODUCTION
iii
INTRODUCTION
This manual is intended to provide detailed descriptions together with all necessary information covering the general
operation of electronic assemblies, electromechanical, servicing control, spare parts, etc. for the product:
"TARGET BRAVO: OPERATION GHOST"
This manual is intended for the owners, personnel managers in charge of operation of this product.
Operate the product after carefully reading and suciently understanding the instructions.
In the unlikely event that the product does not function correctly, DO NOT allow anyone other than a technician
to touch the internal system. Turn o the power to the machine, making sure to unplug the electrical cord from the
outlet, and contact the oce listed below or the point-of-purchase for this product.
Use of this product is unlikely to cause physical injuries or damage to property. However, points that require special
attention are indicated by bold text, the words "STOP, IMPORTANT or CAUTION” and the symbols below.
Indicates important information that, if ignored, may result in the mishandling
of the product and cause faulty operation or damage to the product.
Indicates a warning or caution that, if ignored, may result in the mishandling
of the product and cause faulty operation or damage to the product.
SegaAmusementsEuropeLimited.
42 Barwell Business Park, Leatherhead Road, Chessington, Surrey, KT9 2NY. United Kingdom.
European Sales: [phone] Facsimile: [phone]
USA Sales: +00 (1) 224 265 4287
STS (Spares): [phone] Facsimile: [phone]
email: [email protected] Web: http://www.segaarcade.com
SPECIFICATIONS
42inch Cabinet
Machine Dimensions: 1.44m (56.6in.) [Width] x 1.11m (43.7in.) [Depth]
Machine Height: 2.45m (96.4in.) (Installed)
Machine Weight: 250kg Approx (Installed)
Power, maximum current: -225w-
Rating: 1.2A @ 240vac
2.4A @ 120vac

iv
INTRODUCTION
SPECIFICATIONS
55inch Cabinet
Machine Dimensions: 1.78m (70.1in.) [Width] x 1.13m (44.4in.) [Depth]
Machine Height: 2.71m (106.6in.) (Installed)
Machine Weight: 250kg Approx (Installed)
Power, maximum current: -225w-
Rating: 1.2A @ 240vac
2.4A @ 120vac
Licensing
DYNA Font
The typefaces included herein are solely developed by DynaComware.

INTRODUCTION
v
Parts replacement, maintenance inspections and troubleshooting should be carried out by site maintenance personnel
or other qualied professionals. This manual includes directions for potentially dangerous procedures which should
only be carried out by professionals with the appropriate specialised knowledge.
The site maintenance personnel or other qualied professionals mentioned in this manual are dened as follows:
Site maintenance personnel:
Individuals with experience in maintaining amusement equipment, vending machines, etc., working under the super-
vision of the owner/operator of this product to maintain machines within amusement facilities or similar premises by
carrying out everyday procedures such as assembly, maintenance inspections, and replacement of units/expendable
parts.
Activities to be carried out by site maintenance personnel:
Amusement equipment/vending machine assembly, maintenance inspection and replacement of units/expendable
parts.
Other qualied professionals:
Persons employed by amusement equipment manufacturers, or involved in design, production, testing or mainte-
nance of amusement equipment. The individual should have either graduated from technical school or hold similar
qualications in electrical/electronics/mechanical engineering.
Activities to be carried out by other qualied professionals:
Amusement equipment/vending machine assembly, repair/adjustment of electrical/electronic/mechanical parts.
Denitionof'SiteMaintenencePersonnelorOtherQualiedIndividuals’
Procedures not described in this manual or marked as ‘to be carried out by site
maintenance personnel or other qualied professionals’ should not be carried
out by personnel without the necessary skill or technology. Work carried out by
unqualied persons may cause serious accidents, including electrocution.

vi
INTRODUCTION
WasteofElectricalandElectronicEquipment(WEEE)Statement.
The WEEE (Waste of Electrical and Electronic Equipment) directive places an obligation on all EU based
manufacturers and importers of Electrical and Electronic Equipment (EEE) to ensure waste equipment is disposed of
in accordance with the directive at the end of their useful life.
The symbol shown below will be placed on all products manufactured from 13th August 2005, which indicates this
product must NOT be disposed of with other normal waste. Upon purchasing any EEE from SEGA Amusements
International Ltd. The user accepts responsibility to dispose of their waste equipment by arranging to return it to a
designated UK collection point (AATF) or an Approved Exporter (AE) for the correct recycling of waste electrical
and electronic equipment.
For more information on Approved Authorised Treatment Facilities (AATF) within the UK please consult the
government website www.gov.uk
For users outside of the UK EEE should be disposed of in accordance with the local policy on the recycling of Waste
Electrical and Electronic Equipment.
BatteryRecyclingStatement.
The EC Directive on Batteries and Accumulators (2006/66/EC) aims to minimise the impact of batteries on
the environment and encourage the recovery of the materials they contain. To achieve increased collection and
recycling of waste batteries, the Directive places ‘producer responsibility’ obligations on manufacturers and
importers of portable, industrial and automotive batteries.
The symbol shown below will be on all equipment tted with batteries from 26th September 2008 and indicates
they must NOT be disposed of with other normal waste. Instead, it is the user’s responsibility to dispose of used
batteries by arranging to return them to a designated collection point for the correct recycling.
For more information about where you can send your waste batteries for recycling contact your local authority
oce.
REGISTERED IN ENGLAND REGISTERED NO. 1711515
REGISTERED OFFICE: BLOCK C 42 BARWELL BUSINESS PARK, CHESSINGTON, SURREY KT9 2NY

vii
TABLE OF CONTENTS
INTRODUCTION iii
1HANDLING PRECAUTIONS 1
2 PRECAUTIONS REGARDING INSTALLATION 4
3 PRECAUTIONS REGARDING OPERATION 8
3-1 BEFORE OPERATION 8
3-2 PAYING ATTENTION TO CUSTOMERS 10
4PART DESCRIPTIONS 12
5ACCESSORIES 13
6 ASSEMBLY AND INSTALLATION 14
6-1 INSTALLING THE CABINET 15
6-2 FIXATION TO SITE 19
6-3 POWER SUPPLY AND OTHER CONNECTIONS 21
6-4 TURNING ON THE POWER 22
6-5 CONFIRMATION OF ASSEMBLY 24
6-6 APPLYING WARNING LABELS (EPILEPTIFORM SEIZURES) 25
7PRECAUTIONS WHEN MOVING THE MACHINE 26
7-1 PRECAUTIONS WHEN MOVING FROM SITE 27
8GAME DESCRIPTION 28
8-1 HOW TO PLAY 28
8-2 GAME SCREENS 28
8-3 RELOADING 29
8-4 SWITCHING SHOOTING MODE 29
8-5 RTO (REAL TIME TACTICAL ORDER) 30
8-6 ITEMS 30
8-7 EVENTS 31
8-8 BATTLES WITH BOSSES 31
8-9 GAME OVER 32
8-10CONTINUE PLAY BONUS 33

viii
9EXPLANATION OF TEST AND DATA DISPLAY 34
9-1 SWITCH UNIT AND COIN METER. 35
9-2 SYSTEM TEST MODE 36
9-3 GAME TEST MODE 37
9-4 SYSTEM INFORMATION 48
9-5 STORAGE INFORMATION 50
9-6 JVS TEST 51
9-7 MONITOR TEST 54
9-8 SPEAKER TEST 55
9-9 COIN ASSIGNMENTS 56
9-10CLOCK SETTINGS 60
9-11NETWORK TEST 62
9-12EXIT 64
10 CONTROLLERUNIT(S) 65
10-1 REMOVING THE CONTROLLER UITS 67
10-2 REMOVING THE CONTROLLER SUPPORT 69
10-3 REMOVING THE SCOPE 70
10-4 REMOVING THE MICROSWITCH 72
10-5 REPLACING THE SOLENOID 74
11 GRAPHICS DISPLAY 76
11-1 PRECAUTIONS WHEN HANDLING THE LCD DISPLAY 76
11-2 CLEANING THE SCREEN SURFACE 77
11-3 SCREEN ADJUSTMENT 78
12 COIN HANDLING 82
12-1 CLEANING THE COIN SELECTOR 82
12-2 FAULT FINDING 85
12-3 ADJUSTING THE PRICE OF PLAY (EXCEL) 86
12-4 ADJUSTING THE PRICE OF PLAY (VTS) 87
13 LAMPS AND LIGHTING 88
13-1 COIN DOOR LAMP 88
13-2 START BUTTON LAMP REPLACEMENT 89
13-3 SCREEN LED STRIP REPLACEMENT 90
14 PERIODIC INSPECTION 92
15 TROUBLESHOOTING 94
15-1 TROUBLESHOOTING (WHEN NO ERROR MESSAGE IS SHOWN) 94
16 GAME BOARD 96
16-1HANDLING PRECAUTIONS 97
16-2PARTS DETAILS 98

ix
16-3RINGWIDE COMPONENTS 102
16-4ERROR CODES DISPLAY 103
16-5REPLACING THE BUTTON BATTERY 114
16-6CLEANING RINGWIDE 116
16-7GAME BOARD (RINGWIDE) LOCATION AND REMOVAL 118
17 FUSES AND FUSE REPLACEMENT 121
17-1 CONTROLLER AND LED FUSE REPLACEMENT 121
17-2 MAIN FUSE REPLACEMENT 123
17-3 AC DISTRIBUTION FUSE BD 124
18 DESIGN-RELATED PARTS 125
19 PARTS LIST 127
20 WIRE COLOUR CODE TABLE 137

HANDLING PRECAUTIONS
1
1
1HANDLING PRECAUTIONS
When installing or inspecting the machine, be mindful of the following points and pay attention to ensure that the
player can enjoy the game safely.
Noncompliance with the following points or inappropriate handling running counter to the cautionary matters herein
stated can cause personal injury or damage to the machine.
• Before performing work, be sure to turn the power off. Performing the work
without turning the power off can cause an electric shock or short circuit.
In cases where work should be performed in the status of power on, this
manual always states to that effect.
• To avoid an electric shock or short circuit, do not plug in or unplug quickly.
• To avoid an electric shock, do not plug in or unplug with a wet hand.
• Do not expose power cords or earth wires on the surface, (oor, passage,
etc). If exposed, the power cords and earth wires are susceptible to
damage. Damaged cords and wires can cause an electric shock or short
circuit.
• To avoid causing a re or an electric shock, do not put things on or damage
the power cords.
• During or after installing the product, do not unnecessarily pull the power
cord. If damaged, the power cord can cause a re or an electric shock.
• In the case that the power cord is damaged, ask for a replacement through
where the product was purchased from or the ofce herein stated. Using
the cord as is damaged can cause re, an electric shock or leakage.
• Be sure to perform grounding appropriately. Inappropriate grounding can
cause an electric shock.
• Be sure to use fuses meeting the specied rating. Using fuses exceeding the
specied rating can cause a re or an electric shock.
• Be sure that connections such as IC BD are made properly. Insufficient
insertion can cause an electric shock.
• Specication changes, removal of equipment, conversion and/or addition,
not designated by SEGA are not permitted.
• Failure to observe this may cause a fire or an electric shock. Non-
compliance with this instruction can have a bad influence upon the
physical conditions of players or onlookers, or result in injury during play.
• SEGA shall not be held responsible for damage or compensation for
damage to a third party caused by specication changes not designated
by SEGA.
• Do not perform any work or change parts not listed in this manual. Doing so
may lead to an accident.
• If you need to perform any work not listed in this manual, request work from
the ofce indicated in this manual or the point of purchase, or inquires for
details. Be sure to perform periodic maintenance inspections herein stated.

2
HANDLING PRECAUTIONS
1
• For the IC board circuit inspections, only the use of a logic tester is
recommended. Using a Multi-Tester or General Purpose Tester may result
in damage to IC Circuits.
• Static electricity from your body may damage some electronic devices
on the IC board. Before handling the IC board, touch a grounded metallic
surface so that the static electricity can be discharged.
• Some parts are not designed or manufactured specically for this game
machine. The manufacturers may discontinue or change the specications
of such general-purpose parts. If this is the case, SEGA cannot repair or
replace a failed game machine whether or not a warranty period has
expired.
• Do not touch undesignated places. Touching places not designated can
cause electric shock or short circuit.
• Whenever any fasteners (e.g. screws, nuts) have been lost, be sure to
use replacement fasteners with proper dimensions as specified in this
manual. If fasteners of any other dimensions are used, it could cause
damage and/or separation of parts that result in secondary accidents.
• Specification changes, removal of equipment, conversion and/or
addition, not designated by SEGA are not permitted.
• Failure to observe this may cause a fire or an electric shock. Non-
compliance with this instruction can have a bad influence upon the
physical conditions of players and onlookers, or result in injury during
play.
• SEGA shall not be held responsible for damage or compensation
for damage to a third party caused by specification changes not
designated by SEGA.
• Performing work or parts replacements not described in this manual
could result in accidents. If you need to perform any work not listed in
this manual, request work from the ofce indicated in this manual or the
point-of-purchase, or inquires for details.
• Be sure to perform periodic maintenance inspections herein stated.

HANDLING PRECAUTIONS
3
1
CONCERNING THE STICKER DISPLAY
This SEGA product has stickers attached describing the product manufacture No. (Serial No.) and Electrical
Specications. It also has a Sticker describing where to contact for repair and for purchasing parts.
When inquiring about or asking for repairs, mention the Serial No. and Name of Machine indicated on the Sticker.
The Serial Number indicates the product register. Identical machines could have dierent parts depending on the
date of production. Also, improvements and modifications might have been made after the publication of this
manual. In order to ensure you order the correct parts, mention the Serial No. when contacting the applicable places.
CONCERNING WARNING DISPLAYS
This SEGA product has warning displays on stickers, labels and/or printed instructions adhered/attached to or
incorporated in the places where a potentially hazardous situation could arise. The warning displays are intended
for accident prevention for customers and for avoiding hazardous situations relating to maintenance and servicing
work. Some portions of the cabinet contain high voltage and may cause accidents if touched. When performing
maintenance, be very careful of the warning displays. It is especially important that any complex repair and
replacement work not mentioned herein should be performed by those technical personnel who have knowledge of
electricity and has technical expertise.
In order to prevent accidents, caution any customer ignoring the warnings to cease and desist immediately.

4
PRECAUTIONS REGARDING INSTALLATION LOCATION
2
2 PRECAUTIONS REGARDING INSTALLATION
• This product is an indoor game machine. Do not install it outside. Even indoors,
avoid installing in places mentioned below so as not to cause re, electric
shock, injury and/or malfunction:
• Places subject to rain/water leakage or places subject to high humidity, in the
proximity of an indoor swimming pool and/or shower, etc
• Places subject to direct sunlight or places subject to high temperatures, in the
proximity of heating units, etc
• Places filled with inflammable gas or vicinity of highly inflammable/volatile
chemicals or hazardous matter
• Dusty places
• Sloped surfaces
• Places subject to any type of violent impact
• Vicinity of anti-disaster facilities such as re exits and re extinguishers
• Areas where the temperature exceeds the applicable temperature (ambient
temperature) range of 5 to 30 degrees centigrade
LIMITATIONS OF USAGE
• Be sure to check the Electrical Specifications. Ensure that this product
is compatible with the location's power supply, voltage, and frequency
requirements. A plate describing Electrical Specications is attached to the
product. Noncompliance with the Electrical Specications can cause a re
and electric shock.
• This product requires a breaker and earth mechanism as part of the location
facilities. Using the product without these can cause a re and electric shock.
• Ensure that the indoor wiring for the power supply is rated at 15 A or higher
(AC single phase 100 V ~ 120 V area), and 7 A or higher (AC 220 V ~ 240 V
area). Noncompliance with the Electrical Specications can cause a re and
electric shock.
• Be sure to use an independent power supply equipped with an earth leakage
breaker. Using a power supply without an earth leakage breaker can cause
an outbreak of re if a power surge occurs.
• Putting many loads on one electrical outlet can cause generation of heat and
a re resulting from overload.
• When using an extension cord, ensure that the cord is rated at 15 A or higher
(AC 100 V ~ 120 V area) and 7 A or higher (AC 220 V ~ 240 V area). Using a
cord rated lower than the specied rating can cause a re and electric shock.

PRECAUTIONS REGARDING INSTALLATION LOCATION
5
2
Securing a safe area for operation as described in this manual will ensure
safe operation for players and observers.
SEGA shall not be held responsible for damage or compensation for damage
to a third party, resulting from the failure to observe this instruction.
• For safe operation, use and operate this product in an area measuring at least
1.94 m (76.3 in) in width and 1.91 m (75.1 in) in depth when the 42inch cabinet
is installed. Use and operate this product in an area measuring at least 2.28
m (89.7 in) in width and 1.93 m (75.9 in) in depth when the 55inch cabinet is
installed. SEGA shall not be held responsible for damage or compensation for
damage to a third party, resulting from the failure to observe this instruction.
• The ceiling where this product is installed must be at least 2.5 m (98.4 in) high
for the 42inch cabinet and at least 2.75 m (108.2 in) for the 55inch cabinet. If
the ceiling is too low, the heat emitted from the product may cause it to catch
on re.
• Be sure to provide the sufcient space specied in this manual. Do not allow
objects to block the ventilation ports. This can cause generation of heat and a
re.
• Put the cabinets close together so that people cannot get through or provide
enough space between them that people can go both ways without difculty.
If the cabinets are installed carelessly, people may bump into each other or
the cabinets when passing between them or fall down. To prevent people
from walking between them, place them 0.15 m (5.9 in) apart.
• If the machine does not t through the entryway to the installation location,
do not disassemble it without first consulting the instructions. Specific tools
and adjustment procedures are required to assemble and disassemble the
mechanical parts. Attempting to assemble or disassemble the machine
without consulting the instructions may result in accidents during assembly/
disassembly, electric shock, short circuits, and/or personal injury during
operation. If the machine still does not t through the entryway after following
the procedures in this manual, contact your retailer or the ofce listed in this
manual.
• If the machine is still too large to t through the entryway after following the
procedures listed in this manual, do not tip the machine on its side. Attempting
to transport the machine while it is tipped on its side may cause accidents. It
may also damage or warp parts of the machine, resulting in accidents during
operation.
OPERATION AREA (SINGLE CABINET)

6
PRECAUTIONS REGARDING INSTALLATION LOCATION
2
• To install this product, the entrance must be at least 1.45m (57.1in) in width
and 2.1m (82.6in) in height (without Assy Billboard) and 2.45m (96.4in) (with
Assy Billboard). If the entrance is too narrow, do not tilt the product carelessly.
If all the product weight is put on the casters at one side only, there could be
damage or deformation, causing serious accidents such as workers getting
caught underneath.
To install this product, the entrance must be at least 1.45m (57.1in) in width
and 2.1m (82.6in) in height (without Assy Billboard) and 2.45m (96.4in) (with
Assy Billboard).
Do not attempt to push/pull whilst holding onto the Assy Billboard. This may
result in part damage and/or personal injury.
2.07m (81.49 in)
0.25m (9.8 in)
0.6m (23.6 in)
0.25m (9.8 in)
OPERATION AREA (42inch Cabinet)
1.94m (76.3inches)
1.91m (75.1inches)

PRECAUTIONS REGARDING INSTALLATION LOCATION
7
2
To install this product, the entrance must be at least 1.8m (70.8in) in width
and 2.37m (93.3in) in height (without Assy Billboard) and 2.75m (108.2in)
in height (with Assy Billboard). If the entrance is too narrow, do not tilt the
product carelessly. If all the product weight is put on the casters at one side
only, there could be damage or deformation, causing serious accidents such
as workers getting caught underneath.
Do not attempt to push/pull whilst holding onto the Assy Billboard. This may
result in part damage and/or personal injury.
2.07m (81.49 in)
0.25m (9.8 in)
0.6m (23.6 in)
0.25m (9.8 in)
OPERATION AREA (55inch Cabinet)
2.28m (89.7inches)
1.93m (75.9inches)

8
PRECAUTIONS REGARDING PRODUCT OPERATION
3
3 PRECAUTIONS REGARDING OPERATION
To avoid injury and trouble, be sure to pay attention to the behaviour of visitors and players.
• In order to avoid accidents, check the following before starting the operation:
• To ensure maximum safety for the players and the customers, ensure that
where the product is operated has sufcient lighting to allow any warnings to
be read. Operation under insufcient lighting can cause bodily contact with
each other, hitting accident, and/or trouble between customers.
• Be sure to perform appropriate adjustment of the display (LCD, Plasma, CRT
or Projector). For operation of this machine, do not leave monitor's ickering
or deviation as is. Failure to observe this can have a bad inuence upon the
players' or customers' physical conditions.
• It is suggested to ensure a space allowing the players who feel sick while
playing the game to take a rest.
• Check if all of the adjusters are in contact with the surface. If they are not, the
Cabinet can move and cause an accident.
• Do not put any heavy item on this product. Placing any heavy item on the
product can cause a falling down accident or parts damage.
• Do not climb on the product. Climbing on the product can cause falling down
accidents. To check the top portion of the product, use a step/stepladder.
• To avoid electric shock, check to see if door and cover parts are damaged
or omitted.
• Do not place the following items on top of or near the product or hang them
from the ceiling. Doing so could result in electric shock, short circuits and/or
damage to the parts:
• Flower vases, flowerpots, cups, water tanks, cosmetics, and receptacles/
containers/vessels containing chemicals and water.
3-1 BEFORE OPERATION
Each leg adjuster MUST be lowered so that the
casters are raised approximately 5mm o the oor

PRECAUTIONS REGARDING PRODUCT OPERATION
9
3
• To avoid injury, be sure to provide sufficient space by considering the
potentially crowded situation at the installation location. Insufcient installation
space can cause contact, collisions, and/or trouble between customers.
• During daily cleaning, be sure to check the surface of the control unit and
other parts that the player touches with his/her hands for damage, cracks, or
loose screws. If a player uses the machine while it is damaged, cracked, or
has a loose screw, the player may become injured.
• Check carefully to make sure there are no gaps in the cabinet joints and that
they are not loose. If there are gaps or looseness, players may get their hands
or ngers caught, resulting in an injury.
• Make sure all the doors are locked securely and they do not rattle. If the doors
are not locked properly or there are gaps or rattling, players could get their
ngers or hands caught.
• Be sure to perform appropriate adjustment of the LCD. For operation of this
machine, do not leave monitor’s ickering or deviation as is. Failure to observe
this can have a bad influence upon the players’ or customers’ physical
conditions.
• Inspect for the following items during a trial run. If there is any type of error, use
the Test Mode, etc. to resolve the problem. If you continue use with an error, it
can cause an accident or irreparable parts damage:
- Is there any strangeness in the operability of the control unit?
- Is there any improper adjustment of the LCD screen?
• Prepare a place where players can rest if they feel sick.
Ensure that the buttons (in 3 places) are functioning correctly.
Ensure that there is no damage to cable connectors.
Ensure that the screws are not loose and are all present.

10
PRECAUTIONS REGARDING PRODUCT OPERATION
3
To avoid injury and trouble, be sure to constantly give careful attention to the behaviour and manner of the visitors
and players.
• For safety reasons, do not allow any of the following people to play the game:
- Those who have high blood pressure or a heart problem.
- Those who have experienced muscle convulsion or loss of consciousness
when playing video games, etc.
- Those who have neck or spinal cord problems.
- Those who are intoxicated or under the inuence of drugs.
- Pregnant women.
- Those who are not in good health.
- Those who do not follow the attendant’s instructions.
- Those who cannot grasp the Control Unit securely because of immobility in
ngers, hands or arms.
- Persons who disregard the product's warning displays.
• Even players who have never been adversely affected by light stimulus might
experience dizziness or headache depending on their physical condition
when playing the game.
Small children are especially likely to experience these symptoms. Caution
guardians of small children to keep watch over them during play.
• Instruct those who feel sick during play to have a medical examination.
• To avoid injury from falls and electric shocks due to spilled drinks, instruct the
player not to place heavy items or drinks on the product.
• To avoid electric shocks and short circuits, do not allow customers to put
hands, ngers or extraneous matter in the openings of the product or small
openings in and around the doors.
• To avoid falls and resulting injury, immediately stop the customer from leaning
against or climbing on the product, etc.
• To avoid electric shock and short circuit, do not allow customers to unplug the
power plug without a justiable reason.
• Instruct the guardians of small children to keep watch over their children.
Children cannot sense danger. Allowing small children to get near a player
who is playing the game could result in the children being bumped, struck or
knocked down.
DURINGOPERATION(PAYINGATTENTIONTOCUSTOMERS)
3-2 PAYING ATTENTION TO CUSTOMERS