Sega Ghost Squad User manual

1ST PRINTING FEBUARY ‘05
MANUAL NO. 999-2306
Owner’s Manual
SEGA AMUSEMENTS USA, INC.
Upright Version
®
www.sauservice.com
GAME CODE: CTF

VISIT OUR WEBSITE!
Now with a new look to make your experience
that much easier.

BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING:
To maintain the safety:
To ensure the safe usage of the product, be sure to read the following before using the product. The
following instructions are intended for the users, operators and the personnel in charge of the opera-
tion of the product. After carefully reading and sufficiently understanding the warning displays and
cautions, handle the product appropriately. Be sure to keep this manual nearby the product or else-
where convenient for referring to it when necessary.
Herein, explanations which require special attention are enclosed with dual lines. Depending on the
potentially hazardous degrees, the terms of WARNING, CAUTION, etc. are used. Be sure to under-
stand the contents of the displays before reading the text.
Indicates that mishandling the prod-
uct by disregarding this warning
will cause a potentially hazardous
situation which can result in death
or serious injury.
Indicates that mishandling the product
by disregarding this caution will cause
a slight hazardous situation which can
result in personal injury and or material
damage.
For the safe usage of the product, the following pictographs are used:
Indicates “HANDLE WITH CARE.” In order to protect the human body an equipment,
this display is attached to places where the Owner’s Manual and or Service Manual should
be referred to.
Perform work in accordance with the instructions herein stated.
Instructions for work are explained by paying attention to the aspect of accident prevention. Failing to
perform work as per the instructions can cause accidents. In the case where only those who have tech-
nical expertise should perform the work to avoid hazardous situation, the instructions herein state that the
serviceman should perform such work.
Be sure to turn off power before working on the machine.
To prevent electric shock, be sure to turn off power before starting the work in which the worker touches
the interior of the product. If the work is to be performed in the power-on status, the Instruction Manual
herein always states to that effect.
Be sure to ground the Earth Terminal (this, however, is not required in the case where a power cord
with earth is used).
This product is equipped with the Earth Terminal. When installing the product, Connect the Earth Ter-
minal to the “accurately grounded indoor earth terminal” by using an earth wire. Unless the product is
grounded appropriately, the user can be subject to electric shock. After performing repair, etc. for the
Control equipment, ensure that the Earth Wire is firmly connected to the Control equipment.
Ensure that the Power Supply used is equipped with an Earth Leakage Breaker.
This product does not incorporate the Earth Leakage Breaker. Using a power supply which is not
equipped with the Earth Leakage Breaker can cause a fire when earth leakage occurs.
Be sure to use fuses which meet the specified rating. (only for the machines which use fuses).
Using fuses exceeding the specified rating can cause a fire and electric shock.
WARNING! CAUTION!

Specification changes (removal of equipment, conversion and addition) not designated by SEGA
are not allowed.
The parts of the product include warning labels for safety, covers for personal protection, etc. It is
very hazardous to operate the product by removing parts and or modifying the circuits. Should doors,
lids and protective parts be damaged or lost, refrain from operating the product, and contact where the
product was purchased from or the office herein stated. SEGA shall not be held responsible for any
accidents, compensation for damage to a third party, resulting from the specifications not designated by
SEGA.
Ensure that the product meets the requirements of appropriate Electrical Specifications.
Before installing the product, check for Electrical Specifications. SEGA products have a nameplate on
which Electrical Specifications are described. Ensure that the product is compatible with the power
supply voltage and frequency requirements of the location. Using any Electrical Specifications different
from the designated Specifications can cause a fire and electric shock.
Install and operate the product in places where appropriate lighting is available, allowing warning
labels to be clearly read.
To ensure safety for the customers, labels and printed instructions describing potentially hazardous situ-
ation are applied to places where accidents can be caused. Ensure that where the product is operated
has sufficient lighting allowing the warnings to be read. If any label is peeled off, apply it again imme-
diately. Please place an order with where the product was purchased from or the office herein stated.
When handling the Monitor, be very careful. (Applies only to the product w/monitor.)
Some of the monitor (TV) parts are subject to high tension voltage. Even after running off power, some
portions are still subject to high tension voltage sometimes. Monitor repair and replacement should be
performed only be those technical personnel who have knowledge of electricity and technical expertise.
Be sure to adjust the monitor (projector) properly. (Applies only to the product w/monitor.)
Do not operate the product leaving on-screen flickering or blurring as it is. Using the product with the
monitor not properly adjusted may cause dizziness or a headache to an operator, a player, or the cus-
tomers.
When transporting or reselling this product, be sure to attach this manual to the product.
In the case where commercially available monitors and printers are used in this product, only the con-
tents relating to this product are explained herein. Some commercially available equipment has func-
tions and reactions not stated in this manual. Read this manual together with the specific Instruction
Manual of such equipment.
Descriptions herein contained may be subject to improvement changes without notice.
The contents described herein are fully prepared with due care. However, should any question arise or
errors be found, please contact SEGA.
•
•
INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION.
Normally, at the time of shipment, SEGA products are in a status allowing for usage immediately after
transporting to the location. Nevertheless, an irregular situation may occur during transportation. Before
turning on power, check the following points to ensure that the product has been transported in a satis-
factory status.
Are there any dented portions or defects (cuts, etc.) on the external surfaces of the cabinet?
Are Casters and Adjusters, damaged?
Do the power supply voltage and frequency requirements meet with those of the location?
Are all wiring connectors correctly and securely connected? Unless connected in the correct direction,
connector connections can not be made accurately. Do not insert connectors forcibly.
Do power cords have cuts and dents?
Do the fuses used meet specified rating? Is the Circuit Protector in an energized status?
Are all accessories available?
Can all Doors and Lids be opened with the Accessory keys? Can Doors and Lids be firmly closed?

TABLE OF CONTENTS
BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING:
TABLE OF CONTENTS
INTRODUCTION OF THE OWNER’S MANUAL
1. HANDLING PRECAUTIONS ..........................................................................................
2. PRECAUTIONS CONCERNING INSTALLATION LOCATION ...................................
3. OPERATION .....................................................................................................................
4. ASSEMBLY AND INSTALLATION . ...............................................................................
5. PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE .........................
6. GAME CONTENTS ...........................................................................................................
7. EXPLANATION OF TEST AND DATA DISPLAY ...........................................................
8. CONTROL UNIT (GUN CONTROLLER) ........................................................................
9. MONITOR ...........................................................................................................................
10. COIN SELECTOR ..............................................................................................................
11. DESIGN RELATED PARTS ...............................................................................................
12. PARTS .................................................................................................................................
13. WIRE COLOR CODE TABLE ...........................................................................................
14. WIRING DIAGRAMS ........................................................................................................
1 - 2
3 - 4
5 - 8
9 - 17
18
19 - 35
36 - 59
60 - 66
67 - 69
70 - 72
73
74 - 80
81
XXX

SPECIFICATIONS
INTRODUCTION OF THE OWNERS MANUAL
This Owner's Manual is intended to provide detailed descriptions together with all the
necessary information covering the general operation of electronic assemblies, electrome-
chanicals, servicing control, spare parts, etc. as regards the product,
SEGA GHOST SQUAD UPRIGHT TYPE.
This manual is intended for the owners, personnel and managers in charge of operation
of the product. Operate the product after carefully reading and sufficiently understand-
ing the instructions. If the product fails to function satisfactorily, non-technical personnel
should under no circumstances touch the internal system. Please contact where the prod-
uct was purchased from.
SEGA AMUSEMENTS USA, INC. / CUSTOMER SERVICE
45133 Industrial Drive, Fremont, California 94538, U.S.A.
Phone : [phone]
Fax : [phone]
Use of this product is unlikely to cause physical injuries or damages to property. However,
where special attention is required this is indicated by a thick line, the word "IMPORTANT"
and its sign in this manual.
Indicates that mishandling the product by disregarding this display can cause the
product's intrinsic performance not to be obtained, resulting in malfunctioning.
Installation Space : 44.5 inches width X 71 inches depth
Height : 84 inches
Width : 34.5 inches
Length : 63 inches
Weight : 400 lbs
Power, maximum current : 420 W 3.5 A (AC 120V 60 Hz AREA)
MONITOR : 29 in. Type Display supplied by Sanwa
Monitor: 998-0162
Chassis: 998-0161
STOP
IMPORTANT!
� PRODUCTION DATE �
This SEGA product was produced in the year of:
2005
This signifies that this work was disclosed in 2005.

DEFINITION OF LOCATION MAINTENANCE MAN AND SERVICEMAN
Non-technical personnel who do not have technical knowledge and expertise should
refrain from performing such work that this manual requires the location's main-
tenance man or a serviceman to carry out, or work which is not explained in this
manual. Failing to comply with this instruction can cause a severe accident such
as electric shock.
Ensure that parts replacement, servicing & inspections, and troubleshooting are performed by the
location's maintenance man or the serviceman. It is instructed herein that particularly hazardous work
should be performed by the serviceman who has technical expertise and knowledge.
The location's maintenance man and serviceman are herein defined as follows:
"Location's Maintenance Man" :
Those who have experience in the maintenance of amusement equipment and vending machines, etc.,
and also participate in the servicing and control of the equipment through such routine work as equip-
ment assembly and installation, servicing and inspections, replacement of units and consumables, etc.
within the Amusement Facilities and or locations under the management of the Owner and Owner's
Operators of the product.
Activities of Location's Maintenance Man :
Assembly & installation, servicing & inspections, and replacement of units & consumables as regards
amusement equipment, vending machines, etc.
Serviceman :
Those who participate in the designing, manufacturing, inspections and maintenance service of the
equipment at an amusement equipment manufacturer.
Those who have technical expertise equivalent to that of technical high school graduates as regards
electricity, electronics and or mechanical engineering, and daily take part in the servicing & control
and repair of amusement equipment.
Serviceman's Activities :
Assembly & installation and repair & adjustments of electrical, electronic and mechanical parts of
amusement equipment and vending machines.
WARNING!






1www.seuservice.com
1. HANDLING PRECAUTIONS
When installing or inspecting the machine, be very careful of the following points and pay attention
to ensure that the player can enjoy the game safely.
Non-compliance with the following points or inappropriate handling running counter to the cau-
tionary matters herein stated can cause personal injury or damage to the machine.
� Before performing work, be sure to turn power off. Performing the work with-
out turning power off can cause an electric shock or short circuit. In the case
work should be performed in the status of power on, this manual always states
to that effect.
� To avoid electric shock or short circuit, do not plug in or unplug quickly.
� To avoid electric shock, do not plug in or unplug with a wet hand.
� Do not expose Power Cords and Earth Wires on the surface, (floor, passage,
etc.). If exposed, the Power Cords and Earth Wires are susceptible to damage.
Damaged cords and wires can cause electric shock or short circuit.
� To avoid causing a fire or electric shock, do not put things on or damage Power
Cords.
� When or after installing the product, do not unnecessarily pull the power cord.
If damaged, the power cord can cause a fire or electric shock.
� In case the power cord is damaged, ask for replacement through where the
product was purchased from or the office herein stated. Using the cord as is
damaged can cause fire, electric shock or leakage.
� Be sure to perform grounding appropriately. Inappropriate grounding can cause
an electric shock.
� Be sure to use fuses meeting specified rating. Using fuses exceeding the speci-
fied rating can cause a fire or electric shock.
� Completely make connector connections for IC BD and others. Insufficient
insertion can cause an electric shock.
� Specification changes, removal of equipment, conversion and/or addition, not
designated by SEGA are not permitted.
• Failure to observe this may cause a fire or an electric shock. Non-compliance
with this instruction can have a bad influence upon physical conditions of the
players or the lookers-on, or result in injury during play.
• SEGA shall not be held responsible for damage, compensation for damage to a
third party, caused by specification changes not designated by SEGA.
� Be sure to perform periodic maintenance inspections herein stated.
WARNING!

2
www.seuservice.com
� For the IC board circuit inspections, only the logic tester is allowed. The use of
a multiple-purpose tester is not permitted, so be careful in this regard.
� Some parts are the ones designed and manufactured not specifically for this
game machine. The manufacturers may discontinue, or change the specific-
ations of, such general-purpose parts. If this is the case, Sega cannot repair or
replace a failed game machine whether or not a warranty period has expired.
STOP
IMPORTANT!

3www.seuservice.com
2. PRECAUTIONS CONCERNING INSTALLATION LOCATION
This product is an indoor game machine. Do not install it outside. Even indoors,
avoid installing in places mentioned below so as not to cause a fire, electric shock,
injury and or malfunctioning.
� Places subject to rain or water leakage, or places subject to high humidity in the
proximity of an indoor swimming pool and or shower, etc.
� Places subject to direct sunlight, or places subject to high temperatures in the
proximity of heating units, etc.
� Places filled with inflammable gas or vicinity of highly inflammable/volatile
chemicals or hazardous matter.
� Dusty places.
� Sloped surfaces.
� Places subject to any type of violent impact.
� Vicinity of anti-disaster facilities such as fire exits and fire extinguishrs.
� The operating (ambient) temperature range is from 5°C to 30°C.
� Be sure to check the Electrical Specifications.
Ensure that this product is compatible with the location's power supply, voltage
and frequency requirements.
A plate describing Electrical Specifications is attached to the product.
Non-compliance with the Electrical Specifications can cause a fire and electric
shock.
� This product requires the Breaker and Earth Mechanisms as part of the location
facilities. Using them in a manner not independent can cause a fire and electric
shock.
� Ensure that the indoor wiring for the power supply is rated at 3.5 A or higher
(AC single phase 100~120 V area). Non-compliance with the Electrical Speci-
fications can cause a fire and electric shock.
� Be sure to independently use the power supply equipped with the Earth Leakage
Breaker. Using a power supply without the Earth Leakage Breaker can cause
an outbreak of fire when earth leakage occurs.
� Putting many loads on one electrical outlet can cause generation of heat and a
fire resulting from overload.
� When using an extension cord, ensure that the cord is rated at 3.5 A or higher
(AC 100~120 V area). Using a cord rated lower than the specified rating can
cause a fire and electric shock.
LIMITATIONS OF USAGE REQUIREMENTS
WARNING!
WARNING!

4
www.seuservice.com
OPERATION AREA
FIG. 2
For transporting the machine into the location's building, the minimum
necessary dimensions of the opening (of doors, etc.) are 1 m (W) and
1.7 m (H).
Electric current consumption
MAX. 3.5 A (AC 120 V 60 Hz)
� For the operation of this machine, secure a minimum area of 34.5 in. (W) × 78
in. (D). In order to prevent injury resulting from the falling down accident dur-
ing game play, be sure to secure the minimum area for operation.
� Be sure to provide sufficient space so as to allow this product's ventilation fan to
function efficiently. To avoid machine malfunctioning and a fire, do not place
any obstacles near the ventilation opening.
� SEGA shall not be held responsible for damage, compensation for damage to a
third party, resulting from the failure to observe this instruction.
STOP
IMPORTANT!
WARNING!
*NOTE: Picture may differ from actual unit.

5www.seuservice.com
Approx.5mm
EnsurethatalloftheAdjustersareincontactwiththefloor.
3. OPERATION
PRECAUTIONS TO BE HEEDED BEFORE STARTING THE OPERATION
To avoid injury and trouble, be sure to constantly give careful attention to the behavior and manner
of the visitors and players.
In order to avoid accidents, check the following before starting the operation:
� To ensure maximum safety for the players and the customers, ensure that where
the product is operated has sufficient lighting to allow any warnings to be read.
Operation under insufficient lighting can cause bodily contact with each other,
hitting accident, and or trouble between customers.
� Be sure to perform appropriate adjustment of the monitor (projector). For
operation of this machine, do not leave monitor's flickering or deviation as is.
Failure to observe this can have a bad influence upon the players' or the custom-
ers' physical conditions.
� It is suggested to ensure a space allowing the players who feel sick while play-
ing the game to take a rest.
� Check if all of the adjusters are in
contact with the surface. If they are
not, the Cabinet can move and cause
an accident.
FIG. 3
WARNING!
*NOTE: Picture may differ from actual unit.

6
www.seuservice.com
� Do not put any heavy item on this product. Placing any heavy item on the prod-
uct can cause a falling down accident or parts damage.
� Do not climb on the product. Climbing on the product can cause falling down
accidents. To check the top portion of the product, use a step.
� To avoid electric shock, check to see if door & cover parts are damaged or omit-
ted.
� To avoid electric shock, short circuit and or parts damage, do not put the follow-
ing items on or in the periphery of the product.
Flower vases, flowerpots, cups, water tanks, cosmetics, and receptacles/
containers/vessels containing chemicals and water.
� To avoid injury, be sure to provide sufficient space by considering the poten-
tially crowded situation at the installation location. Insufficient installation
space can cause making bodily contact with each other, hitting accidents, and
or trouble between customers.
� Every day when cleaning the Control Unit (Shotgun), inspect the Shotgun and
make sure that there are no scratches or cracks in the surface, and that the fas-
tening screws are not loose. If the game is played with scratches, cracks or loose
screws it can cause injuries to the player or to people nearby.
Players with bare hands directly hold the controller. For operation, it is recom-
mended that the wet towels (paper towels) be provided.
CAUTION!
STOP
IMPORTANT!
WARNING!
WARNING: HAZARD TO EPILEPTICS.
� A very small portion of the population has a condition which may cause them
to experience epileptic seizures or have momentary loss of consciousness when
viewing certain kinds of flashing lights or patterns that are present in our daily
environment. These persons may experience seizures while watching some
kinds of television pictures or playing certain video games. People who have
not had any previous seizures may nonetheless have an undetected epileptic
condition.
� If you or anyone in your family has experienced symptoms linked to an epi-
leptic condition (e.g., seizures or loss of awareness), immediately consult your
physician before using any video games.
� We recommend that parents observe their children while they play video
games. If you or your child experience the following symptoms: dizziness,
altered vision, eye or muscle twitching, involuntary movements, loss of aware-
ness, disorientation, or convulsions, DISCONTINUE USE IMMEDIATELY
and consult your physician.
WARNING!

7www.seuservice.com
To avoid injury and trouble, be sure to constantly give careful attention to the behavior and manner
of the visitors and players.
PRECAUTIONS TO BE HEEDED DURING OPERATION(PAYING ATTENTION TO CUSTOMERS)
� To avoid injury and accidents, those who fall under the following categories are
not allowed to play the game.
• Those who need assistance such as the use of an apparatus when walking.
• Those who have high blood pressure or a heart problem.
• Those who have experienced muscle convulsion or loss of consciousness when
playing video game, etc.
• Those who have a trouble in the neck and or spinal cord.
• Intoxicated persons.
• Pregnant women or those who are in the likelihood of pregnancy.
• Persons susceptible to motion sickness.
• Persons whose act runs counter to the product's warning displays.
� A player who has never been adversely affected by light stimulus might experi-
ence dizziness or headache depending on his physical condition when playing
the game. Especially, small children can be subject to those conditions. Cau-
tion guardians of small children to keep watch on their children during play.
� Instruct those who feel sick during play to have a medical examination.
� To avoid injury resulting from falling down and electric shock due to spilled
drinks, instruct the player not to place heavy items or drinks on the product.
� To avoid electric shock and short circuit, do not allow customers to put hands
and fingers or extraneous matter in the openings of the product or small open-
ings in or around the doors.
� To avoid falling down and injury resulting from falling down, immediately stop
the customer's leaning against or climbing on the product, etc.
� To avoid electric shock and short circuit, do not allow the customers to unplug
the power plug without a justifiable reason.
� Be sure to instruct the adult responsible for children to watch them.
Children cannot sense danger. Approaching the player during play may result
in accidental contact, collisions or falls.
If the Shotgun is pulled from the Gun Holder and dropped on the head it may
cause injury.
� Caution the player not to wrap the Shotgun cord around his/her wrist or neck,
as this can lead to serious injury.

8
www.seuservice.com
� Immediately stop such violent acts as hitting and kicking the product. Such
violent acts can cause parts damage or falling down, resulting in injury due to
fragments and falling down.
� To avoid injury resulting from falling down, immediately stop the customer's
leaning against or sitting down on the Gun Holder. Such acts can cause parts
damage/deformation.
� Be sure to immediately stop any violent play, such as waving the Rifle around
or rapid back and forth action, as this may cause injury to the player or people
nearby.
� If the player is too close to the Cabinet, the Rifle can strike the Cabinet during
play and cause accidents. Be sure to caution the player to maintain a safe
distance from the Cabinet while playing.
� When 2 people are playing at the same time, be sure to caution them keep a
safe distance from the other player. The Rifle is long and can strike the other
player if it is waved carelessly.
� Be sure to caution the player to grip the Rifle firmly while playing. If the Rifle
is dropped, it can cause injury to the player.
� Large rings etc., can cause injury to the fingers during play. Be sure to caution
the player to remove accessories that may cause accidents before commencing
play.
� Be sure to caution players not to have 2 or more people holding 1 Rifle, as this
may result in accidental contact or collision.
The Rifles for use on 1P side (left side) and 2P side (right side) are different. Ensure
that players do not confuse the right and left side guns when starting play.
CAUTION!
STOP
IMPORTANT!

9www.seuservice.com
4. ASSEMBLING AND INSTALLATION
● Perform assembly work by following the procedure herein stated. Failing to
comply with the instructions can cause electric shock hazard.
● Perform assembling as per this manual. Since this is a complex machine,
erroneous assembling can cause an electric shock, machine damage and or not
functioning as per specified performance.
● When assembling, be sure to use plural persons. Depending on the assembly
work, there are some cases in which working by one person alone can cause
personal injury or parts damage.
● Ensure that connectors are accurately connected. Incomplete connections can
cause electric shock hazard.
● Be careful not to damage the wires. Damaged wires may cause electric shock
or short circuit or present a fire risk.
● Do not carelessly push the PTV. Pushing the PTV carelessly can cause the
PTV to fall down.
● This work should be performed by the Location's Maintenance Man or
Serviceman. Performing work by non-technical personnel can cause a severe
accident such as electric shock. Failing to comply with this instruction can
cause a severe accident such as electric shock to the player during operation.
● Provide sufficient space so that assembling can be performed. Performing
work in places with narrow space or low ceiling may cause an accident and
assembly work to be difficult.
● To perform work safely and avoid serious accident such as the cabinet's falling
down, do not perform work in places where step-like grade differences, a ditch,
or slope exist.
● When handling plastic parts, use care. Do not give a shock or apply excessive
load to the fluorescent lamps and plastic parts. Failure to observe this can
cause parts damage, resulting in injury due to fragments, cracks and broken
pieces.
● To perform work safely and securely, be sure to prepare a step which is in
a secure and stable condition. Performing work without using the step can
cause violent falling down accidents.
● Make sure that the GD cable connector is inserted parallel to the plug.
Improper insertion may cause damage to the connector and present a fire risk.
WARNING!
CAUTION!

10
www.seuservice.com
INSTALLING THE GD-ROM DRIVE (SETTING GD-ROM DISC)
POWER SUPPLY, AND EARTH CONNECTION
TURNING POWER ON
When carrying out the assembling and installation, follow the following 8-item sequence.
The master key (accessories) in addition to the tools such as a Phillips type screwdriver, wrench,
socket wrench and Ratchet Handle are required for the assembly work.
WRENCH (for hexagon bolt)
Phillips type screwdriver
1
2
3
TAMPERPROOF
WRENCH
T-40 Torx 5/16-18 (1)
T-27 Torx 1/4-20 (1)
T-15 Torx 8/32 (1)
T-10 Torx (1)
Tool (Included with Unit)

11 www.seuservice.com
INSTALLING THE GD-ROM DRIVE (SETTING GD-ROM DISC)
● Carefully handle the GD-ROM drive so as not to contaminate the disc and the
readout lens with stains and dust particles.
● Do not continue to use the scratched GD-ROM disc. The scratched GD-ROM
disc may cause the system to malfunction.
● Set the GD-ROM disc onto the GD-ROM drive with its labeled side facing
upward.
● The key chip is a precision device. Handle it carefully and avoid exposure to
heat, shock and static electricity, as these may cause damage to the device.
● The key chip is contained in the GD-ROM disc case. Always use them as a set.
This section explains how to remove the ASSY MAIN BD from the PTV cabinet, set the GD-ROM
disk onto the GD-ROM drive, and install the GD-ROM drive onto the ASSY MAIN BD.
GD DRIVE BRACKET GD-ROM DRIVE
PHOTO 6. 5 a
Use the 4 tapping screws to fix the GD-ROM drive bracket onto the GD-ROM drive. Be careful
about a fixing direction.
TAPPING SCREW (4)
4×8
FIG. 6. 5 a
GD DRIVE BRACKET
GD-ROM DRIVE
FIG. 6. 5 b
Unpack the shipping
crate, and take out the
GD-ROM drive, GD-
ROM drive bracket,
and GD-ROM disc.
CAUTION for U. S. A., Europe, and Australia:
Attach the 2 caution stickers for a laser ray onto
the GD-ROM drive.
STOP
IMPORTANT!
1
1
2

12
www.seuservice.com
Remove the 1 truss head screw that
fixes the GD-ROM drive lid (DISC
LID). And turn clockwise the lid to
remove.
TRUSS SCREW (1)
M3×8
PHOTO 6. 5 b
Set the GD-ROM disc onto the GD-ROM drive with its labeled side facing upward.
Return the lid to its original place, and fix it with 1 truss head screw. Be careful not to fasten the
screw too tightly.
TRUSS SCREW (1)
M3×8
PHOTO 6. 5 c
3
4
5

13 www.seuservice.com
Insert both the GD cable connector (for data communication) and the power cord connector (JST
NH6P) into the GD-ROM drive. Be careful about an inserting direction in this instance. Make sure
that the connectors are inserted firmly and completely.
Place the ASSY MAIN BD on a
flat vertical surface.
Using the 4 screws, fix the
GD-ROM drive onto the ASSY
MAIN BD.
6
7
SCREW (4)
M4×16, w/flat & spring washers
PHOTO 6. 5 h
PHOTO 6. 5 i
*NOTE: Picture may differ from actual unit.
GD Cable connector
Power Cord connector