Sega AFTER BURNER CLIMAX User manual

OWNER'S MANUAL
IMPORTANT
●Before using this product, read this manual carefully to understand the
contents herein stated.
●After reading this manual, be sure to keep it near the product or in a
convinient place for easy reference when necessary.
OWNER'S MANUALAFTER BURNER CLIMAX SUPER DELUXE ABS-MNL-0031E
SEGA CORPORATION
Nissay Aroma Building, 5-37-1, Kamata, Ohta-ku, Tokyo 144-8721, Japan
cSEGA
ABS-MNL-0031E
1st PRINTING

TABLE OF CONTENTS
i
TABLE OF CONTENTS
E0-0609
BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING:
TABLE OF CONTENTS
INTRODUCTION
1HANDLING PRECAUTIONS ......................................................................... 1
2PRECAUTIONS REGARDING INSTALLATION LOCATION ..................................... 5
2-1 LIMITATIONS OF USAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2-2 OPERATION AREA .. . . . . . . . . . . . .. . . . . . . .. . . . . . .. . . . . . . .. . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . 7
3PRECAUTIONS REGARDING PRODUCT OPERATION ............................. 9
3-1 BEFORE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3-2 DURING OPERATION (PAYING ATTENTION TO CUSTOMERS) ................................12
4PART DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5ACCESSORIES ........................................................................................... 17
6ASSEMBLY AND INSTALLATION .............................................................. 20
7PRECAUTIONS WHEN MOVING THE MACHINE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
8GAME DESCRIPTION ................................................................................. 58
9EXPLANATION OF TEST AND DATA DISPLAY......................................... 72
9-1 SWITCH UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
9-2 COIN METER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
9-3 SYSTEM TEST MODE ...................................................................................................76
9-4 GAME TEST MODE .......................................................................................................77
a.INPUT TEST ...............................................................................................................79
b.OUTPUT TEST ...........................................................................................................81
c.GAME ASSIGNMENTS ..............................................................................................84
d.NETWORK SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
e.CALIBRATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
f.BOOKKEEPING .......................................................................................................... 94
g.BACKUP DATA CLEAR .... . . . . . . ........ . . . . . . ........ . . . . . . . ........ . . . ...... . . . . . . ........ . . . . . . . ........ . . . . . . .. 97
9-5 MOTION CONTROL BOARD TEST MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
a.MOTION CONTROL BOARD TEST MODE MENU .................................................100
b.NETWORK SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
c.MOTION TEST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
10 MONITOR .................................................................................................. 103
10-1 CAUTIONS/WARNINGS REGARDING SAFETY FOR HANDLING THE MONITOR . . . . . 103
10-2 ADJUSTMENT PROCEDURE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
ABS-MNL-0031E

ii
TABLE OF CONTENTS
11 CONTROL STICK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
11-1 HOW TO REMOVE CONTROL STICK ......................................................................107
11-2 GREASING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
11-3 VOLUME REPLACEMENT ........................................................................................112
11-4 MICROSWITCH REPLACEMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
11-5 GUIDE PLATE REPLACEMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
12 THROTTLE LEVER ................................................................................... 119
12-1 GREASING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
12-2 VOLUME ADJUSTMENT OR REPLACEMENT ........................................................122
13 COIN SELECTOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
14 FLOOR SENSOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
15 GREASE UP .............................................................................................. 131
15-1 SUMMARY OF GREASE UP .....................................................................................131
15-2 HOW TO GREASE UP ...............................................................................................132
a. BALLJOINT .............................................................................................................132
b. ACTUATOR .............................................................................................................133
c. UNIVERSAL JOINT IN THE ACTUATOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
d. GUIDE RAIL ............................................................................................................135
16 BELLOWS ................................................................................................. 136
17 PERIODIC INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
18 TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
18-1 GAME BOARD ERROR MESSAGES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
18-2 TROUBLESHOOTING TABLE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
18-3 MOTION CONTROL BOARD ERROR MESSAGES .................................................146
19 GAME BOARD .......................................................................................... 148
19-1 HOW TO REMOVE GAME BOARD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
19-2 COMPOSITION OF THE GAME BOARD ..................................................................151
20 DESIGN RELATED PARTS ...................................................................... 152
21 NETWORK PLAY ...................................................................................... 153
20-1 PRECAUTIONS REGARDING NETWORK PLAY SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
20-2 NETWORK CABLE CONNECTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
20-3 NETWORK PLAY SETTING ......................................................................................157
20-4 PRECAUTIONS IN NETWORK PLAY .......................................................................160
22 PARTS LIST .............................................................................................. 161
23 WIRING DIAGRAM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191

INTRODUCTION
iii
INTRODUCTION
This manual is intended to provide detailed descriptions together with all the necessary information covering the
general operation of electronic assemblies, electro-mechanicals, servicing control, spare parts, etc. for the product,
“AFTER BURNER CLIMAX. SUPER DELUXE”
This manual is intended for the owners, personnel and managers in charge of operation of the product.
Operate the product after carefully reading and sufficiently understanding the instructions.
In the unlikely event that the product does not function correctly, DO NOT allow anyone other than a technician
to touch the internal system. Turn off the power to the machine, making sure to unplug the electrical cord from the
outlet, and contact the office listed below or the point-of-purchase for this product.
Use of this product is unlikely to cause physical injuries or damage to property. However, points that require special
attention are indicated by bold text, the word “IMPORTANT” and the symbol below.
Indicates important information that, if ignored, may result in the mishandling of
the product and cause faulty operation or damage to the product.
Sega Amusements U.S.A., Inc.
800 Arthur Avenue, Elk Grove Village, IL 60007-5215, U.S.A.
TEL: [phone]
TOLL FREE: 1-888-877-2669
FAX: [phone]
SEGA AMUSEMENTS EUROPE, LTD.
Suite 3a, Oaks House 12-22, West Street, Epsom, Surrey, KT18 7RG, United Kingdom
Telephone: [phone] Facsimile: [phone]
e-mail: [email protected] http://www.sega-amusements.co.uk
SPECIFICATIONS
Installation space: 1,330 mm (52.4 in.) [Width] x 2,580 mm (101.6 in.) [Depth]
Height: 1,990 mm (78.3 in.)
Weight: 700 kg (1,543.2 lbs.)
Power, maximum current: 1,100 W, 5.10 A (AC 220 V, 60 Hz Area)
(AC 220 V, 50 Hz Area)
(AC 230 V, 50 Hz Area)
(AC 208 V, 60 Hz Area)
Monitor: 40Wide Type LCD Monitor
NOTE: The contents herein described are subject to change without notice.

iv
INTRODUCTION
Definition of ‘Site Maintenance Personnel or Other Qualified Individuals’
Parts replacement, maintenance inspections and troubleshooting should be carried out by site maintenance personnel
or other qualified professionals. This manual includes directions for potentially dangerous procedures which should
only be carried out by professionals with the appropriate specialized knowledge.
The site maintenance personnel or other qualified professionals mentioned in this manual are defined as follows:
Site maintenance personnel:
Individuals with experience in maintaining amusement equipment, vending machines, etc., working under the
supervision of the owner/operator of this product to maintain machines within amusement facilities or similar
premises by carrying out everyday procedures such as assembly, maintenance inspections, and replacement of units/
expendable parts.
Activities to be carried out by site maintenance personnel:
Amusement equipment/vending machine assembly, maintenance inspection and replacement of units/expendable
parts.
Other qualified professionals:
Persons employed by amusement equipment manufacturers, or involved in design, production, testing or
maintenance of amusement equipment. The individual should have either graduated from technical school or hold
similar qualifications in electrical/electronics/mechanical engineering.
Activities to be carried out by other qualified professionals:
Amusement equipment/vending machine assembly, repair/adjustment of electrical/electronic/mechanical parts.
Procedures not described in this manual or marked as 'to be carried out by site
maintenance personnel or other qualified professionals' should not be carried
out by personnel without the necessary skill or technology. Work carried out by
unqualified persons may cause serious accidents, including electrocution.

INTRODUCTION
v
This marking shown on the product or its literature, indicates that it
should not be disposed with other household wastes at the end of its
working life. To prevent possible harm to the environment or human
health from uncontrolled wastes disposal, please separate this from
other types of wastes and recycle it responsibly to promote the
substainable reuse of meterial resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they can
take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions
of the purchase contract. This product should not be mixed with other commercial
wastes for disposal.

HANDLING PRECAUTIONS
1
1
HANDLING PRECAUTIONS
1
When installing or inspecting the machine, be very careful of the following points and pay attention to ensure that
the player can enjoy the game safely.
Non-compliance with the following points or inappropriate handling running counter to the cautionary matters
herein stated can cause personal injury or damage to the machine.
• Before performing work, be sure to turn the power off. Performing the work
without turning the power off can cause an electric shock or short circuit. In the
case work should be performed in the status of power on, this manual always
states to that effect.
• Do not expose power cords or ground wires on the surface, (floor, passage,
etc.). If exposed, the power cords and ground wires are susceptible to damage.
Damaged cords and wires can cause an electric shock or short circuit.
• To avoid causing a fire or an electric shock, do not put things on or damage the
power cords.
• When, or after installing the product, do not unnecessarily pull the power cord. If
damaged, the power cord can cause a fire or an electric shock.
• In case the power cord is damaged, ask for a replacement through where the
product was purchased from or the office herein stated. Using the cord as is
damaged can cause fire, an electric shock or leakage.
• Be sure to perform grounding appropriately. Inappropriate grounding can
cause an electric shock.
• Be sure to use fuses meeting the specified rating. Using fuses exceeding the
specified rating can cause a fire or an electric shock.
• Be sure that connections such as IC BD are made properly. Insufficient insertion
can cause an electric shock.
• Specification changes, removal of equipment, conversion and/or addition, not
designated by SEGA are not permitted.
- Failure to observe this may cause a fire or an electric shock. Non-compliance
with this instruction can have a bad influence upon physical conditions of the
players or the onlookers, or result in injury during play.
- SEGA shall not be held responsible for damage, compensation for damage to
a third party, caused by specification changes not designated by SEGA.
• Be sure to perform periodic maintenance inspections herein stated.

1
HANDLING PRECAUTIONS
2
• For the IC board circuit inspections, only the logic tester is allowed. The use of a
multiple-purpose tester is not permitted, so be careful in this regard.
• Static electricity from your body may damage some electronics devices on the
IC board. Before handling the IC board, touch a grounded metallic surface so
that the static electricity can be discharged.
• Some parts are not designed and manufactured specifically for this game
machine. The manufacturers may discontinue, or change the specifications of
such general-purpose parts. If this is the case, SEGA cannot repair or replace a
failed game machine whether or not a warranty period has expired.

HANDLING PRECAUTIONS
1
3
CONCERNING THE STICKER DISPLAY
This SEGA product has stickers attached describing the product manufacture No. (Serial No.) and Electrical
Specifications. It also has a Sticker describing where to contact for repair and for purchasing parts.
When inquiring about or asking for repairs, mention the Serial No. and Name of Machine indicated on the Sticker.
The Serial Number indicates the product register. Identical machines could have different parts depending on the
date of production. Also, improvements and modifications might have been made after the publication of this
manual. In order to ensure you order the correct parts, mention the Serial No. when contacting the applicable places.
CONCERNING WARNING DISPLAYS
This SEGA product has warning displays on stickers, labels and/or printed instructions adhered/attached to or
incorporated in the places where a potentially hazardous situation could arise. The warning displays are intended
for accident prevention for customers and for avoiding hazardous situations relating to maintenance and servicing
work. Some portions of the cabinet contain high voltage and may cause accidents if touched. When performing
maintenance, be very careful of the warning displays. It is especially important that any complex repair and
replacement work not mentioned herein should be performed by those technical personnel who have knowledge of
electricity and technical expertise.
In order to prevent accidents, caution any customer ignoring the warnings to cease and desist immediately.

1
HANDLING PRECAUTIONS
4
Serial No. Display
Electrical Specifications Display
The opposition part is equal to do

PRECAUTIONS REGARDING INSTALLATION LOCATION
2
5
PRECAUTIONS REGARDING INSTALLATION LOCATION
2
This product is an indoor game machine. Do not install it outside. Even indoors,
avoid installing in places mentioned below so as not to cause a fire, electric
shock, injury and/or malfunction.
- Places subject to rain or water leakage, or places subject to high humidity in the
proximity of an indoor swimming pool and/or shower, etc.
- Places subject to direct sunlight, or places subject to high temperatures in the
proximity of heating units, etc.
- Places filled with inflammable gas or vicinity of highly inflammable/volatile
chemicals or hazardous matter.
- Dusty places.
- Sloped surfaces.
- Places subject to any type of violent impact.
- Vicinity of anti-disaster facilities such as fire exits and fire extinguishers.
- The operating (ambient) temperature range is from 5 to 30 degrees.
2-1 LIMITATIONS OF USAGE
• Be sure to check the Electrical Specifications. Ensure that this product
is compatible with the location's power supply, voltage, and frequency
requirements. A plate describing Electrical Specifications is attached to the
product. Non-compliance with the Electrical Specifications can cause a fire
and electric shock.
• This product requires a breaker and earth mechanism as part of the location
facilities. Using the product without these can cause a fire and electric shock.
• Ensure that the indoor wiring for the power supply is rated at 5.1A or higher
(AC 200~208V, 220V, 230V, 240V area). Non-compliance with the Electrical
Specifications can cause a fire and electric shock.
• Be sure to use an independent power supply equipped with an earth leakage
breaker. Using a power supply without an earth leakage breaker can cause an
outbreak of fire if a power surge occurs.
• Putting many loads on one electrical outlet can cause generation of heat and a
fi r e resulting from overload.
• When using an extension cord, ensure that the cord is rated at 5.1A or higher (AC
200~208V, 220V, 230V, 240V area). Using a cord rated lower than the specified
rating can cause a fire and electric shock.

2
PRECAUTIONS REGARDING INSTALLATION LOCATION
6
Electricity Consumption:
MAX. 5.1 A
(AC 200~208V, 220V, 230V, 240V, 50/60 Hz)
• Check your electric specifications.
Check whether the product conforms to the voltage, current and frequancy
provided at the installation location. For the electric specifications, see the
plate (label) attaches on the product.
• Inside the installaton locations, a breaker and an earth connections for the
product are required. An independent electric source for the product should be
provided to prevent fire or electric shock.
• Make sure to use the power cable in accordance with power consumption as
described below. Using power cable of other electric specifications can cause
a fire or electric shock.
• Make sure to use the power with independent circuit breaker. Using any power
source without circuit breaker can cause a fire.
• Do net have many electrical cords connected to a single socket. Overload can
cause the generation of heat or a fire.
• If an extention cord is used, it should be rated the max current or higheras
described below. Using a cord of different specifications can cause a fire or
electric shock.

PRECAUTIONS REGARDING INSTALLATION LOCATION
2
7
2-2 OPERATION AREA
• For the operation of this machine, secure a minimum area of 2.88 m (W) x 3.13
m (D). The dimensions of the base periphery are established in consideration of
ventilation, maintenance and customer passage. With this product there is the
danger that someone could fall down while getting onto the base or the seat.
And if they fall and hit their head, there could be a very serious injury. Be sure to
always secure enough space as prescribed in this manual.
• Be sure to provide sufficient space specified in this manual. Do not allow
objects to block the ventilation ports. It can cause generation of heat and a fire.
• SEGA shall not be held responsible for damage or compensation for damage to
a third party, resulting from the failure to observe this instruction.
• If the machine does not fit through the entryway to the installation location, do
not disassemble it without first consulting the instructions. The machine should
only be disassembled in accordance with the instructions listed in this manual;
do not attempt to disassemble it in any other way. Specific tools and adjustment
procedures are required to assemble and disassemble the mechanical parts.
Attempting to assemble or disassemble the machine without consulting the
instructions may result in accidents during assembly/disassembly and electric
shock, short circuits, and/or personal injury during operation.
• If the machine is still too large to fit through the entryway after following the
procedures listed in this manual, do not tip the machine on its side. Attempting
to transport the machine while it is tipped on its side may cause accidents. It
may also damage or warp parts of the machine, resulting in accidents during
operation.
• To install this product, the entrance must be at least 1.4 m in width and 2 m in
height. If the entrance is too narrow, do not tilt the product carelessly. If all the
product weight is put on the casters at one side only, there could be damages
or deformations, causing serious accidents such as workers getting caught
underneath.

2
PRECAUTIONS REGARDING INSTALLATION LOCATION
8
FIG. 2 Installation and operation area

PRECAUTIONS REGARDING PRODUCT OPERATION
3
9
PRECAUTIONS REGARDING PRODUCT OPERATION
3
To avoid injury and trouble, be sure to pay attention to the behavior of visitors and players.
3-1 BEFORE OPERATION
In order to avoid accidents, check the following before starting the operation:
• To ensure maximum safety for the players and the customers, ensure that where
the product is operated has sufficient lighting to allow any warnings to be read.
Operation under insufficient lighting can cause bodily contact with each other,
hitting accident, and/or trouble between customers.
• Be sure to perform appropriate adjustment of the monitor (projector). For
operation of this machine, do not leave monitor's flickering or deviation as
is. Failure to observe this can have a bad influence upon the players' or the
customers' physical conditions.
• It is suggested to ensure a space allowing the players who feel sick while
playing the game to take a rest.
• Check if all of the adjusters are in contact with the surface. If they are not, the
Cabinet can move and cause an accident.
• Do not put any heavy item on this product. Placing any heavy item on the
product can cause a falling down accident or parts damage.
• Do not climb on the product. Climbing on the product can cause falling down
accidents. To check the top portion of the product, use a step ladder.
Ensure that all of the Adjusters are in contact with the floor.

3
PRECAUTIONS REGARDING PRODUCT OPERATION
10
• To avoid electric shock, check to see if door & cover parts are damaged or
omitted.
• To avoid electric shock, short circuit and/or parts damage, do not put the
following items on or in the periphery of the product.
Flower vases, flowerpots, cups, water tanks, cosmetics, and receptacles/
containers/vessels containing chemicals and water.
• Make sure the surrounding area is secure before turning the power on. The
machine will automatically go through an initialization process after being
turned on. The seat will move left and right, and persons standing in the vicinity
of the machine may be struck or knocked down.
• Be sure to perform a test run of the machine and inspect its safety devices
before putting it into operation. Because the machine's seat swerves to the left
and right, it is equipped with safety devices. In order to ensure that these safety
devices are functioning properly, it is imperative that the following checks be
performed on a regular basis:
-Does the seatbelt hold the player's body firmly in place?
-Are there any damaged or frayed spots on the seatbelt?
-When the seatbelt is released, does the seat stop moving?
-Are any of the seat parts loose or wobbly?
-When the "Motion Stop" button is pressed, does the seat stop moving?
-When the safety sensor detects a foreign object, does the seat stop moving?
• When performing the above safety checks, verify also that the seat is moving
properly. Accidents may occur if the seat is moving abnormally. For this reason,
do not operate the machine in such cases until the problem is resolved.
-Does the seat move in the direction that the controls are pressed?
-Does the seat move smoothly?
-Does the seat shake or rattle?
-Are any unusual sounds produced during seat motion?
-Does the seat experience unusual vibration while moving?
-When the game is over, does the seat come to rest in a level position?
• If the seat motion mechanism begins to malfunction, immediately cease
operation, turn off the power, unplug the power cord, and contact the office
listed in this manual or your retailer. Continuing to operate the machine without
resolving the problem may result in serious accidents such as electric shock,
short circuits, or fire, and/or cause the machine to tip over.
• Requests for maintenance of the seat motion mechanism should be directed to
the office listed in this manual or your retailer. Attempts to perform maintenance
by persons other than specially trained technicians may result in injury to the
party performing the maintenance and/or to players during product operation.
• The seat will continue to move even if it comes into contact with persons other
than the player. In order to ensure a safe operating environment, place the
machine so that one side is adjacent to the back of another game machine or
to the wall.

PRECAUTIONS REGARDING PRODUCT OPERATION
3
11
• To avoid injury, be sure to provide sufficient space by considering the potentially
crowded situation at the installation location. Insufficient installation space can
cause making bodily contact with each other, hitting accidents, and/or trouble
between customers.
• Check the control devices to make sure that there are no scratches or cracks
on parts touched by players, as such defects can cause injury to hands and
fi n gers.

3
PRECAUTIONS REGARDING PRODUCT OPERATION
12
3-2 DURING OPERATION (PAYING ATTENTION TO CUSTOMERS)
To avoid injury and trouble, be sure to pay attention to the behavior of visitors and players.
• For safety reasons, do not allow any of the following people to play the game.
- Those who have high blood pressure or a heart problem.
- Those who have experienced muscle convulsion or loss of consciousness
when playing video games, etc.
- Those who have neck or spinal cord problems.
- Those who are intoxicated or under the influence of drugs.
- Pregnant women.
- Those who are not in good health.
- Those who do not follow the attendant’s instructions.
- Those who cannot grasp the Control Unit securely because of immobility in
fi n gers, hands or arms.
- Persons who disregard the product's warning displays.
The game cannot be played while sitting in a wheelchair.
• Even players who have never been adversely affected by light stimulus might
experience dizziness or headache depending on their physical condition when
playing the game.
• Instruct those who feel sick during play to have a medical examination.
• To avoid injury from falls and electric shocks due to spilled drinks, instruct the
player not to place heavy items or drinks on the product.
• To avoid electric shocks and short circuits, do not allow customers to put
hands and fingers or extraneous matter in the openings of the product or small
openings in or around the doors.
• To avoid falls and resulting injury, immediately stop the customer from leaning
against or climbing on the product, etc.
• To avoid electric shock and short circuit, do not allow customers to unplug the
power plug without a justifiable reason.
• For safety reasons, this game must not be played by persons less than 140 cm in
height. Customers should be told that this is because the seatbelt cannot secure
such persons in place.

PRECAUTIONS REGARDING PRODUCT OPERATION
3
13
• Playing the game without first securing the seatbelt may cause customers to
fall out. Customers should be instructed always to secure themselves with the
seatbelt before playing the game.
• Prevent customers from sitting two at a time in the seat. This game is for one
player only. If two or more customers attempt to sit in the seat and play at the
same time, they may hit their heads, hands, or elbows, possibly resulting in
serious injury.

3
PRECAUTIONS REGARDING PRODUCT OPERATION
14
• Customers should be warned not to place
children on their laps while they play the
game. Doing so may cause the child to
become trapped between the player
and the control panel and/or cause the
machine to tip over.
• Persons other than the
player should not be
allowed to approach the
machine while the seat
is in motion. Such actions
may result in sideswiping
and/or collision accidents.
The safety sensor is only
able to detect foreign
objects on top of the
base. Young children are
especially susceptible
to this danger; for this
reason, customers should
be instructed to watch
their children closely.
• Be careful not to remove your foot from the footrest during play. If you remove
your foot carelessly, it could be caught up in something, or someone could trip
over it, resulting in a fracture, sprain, or other injury.
• Prevent customers from playing the game with bag straps or scarves wrapped
around their necks or while holding on to drinks, as this can lead to accidents.
• If a player appears to be in distress, stop the seat motion immediately by
pressing the "Motion Stop" button.
• If it becomes crowded within the store and it appears that motion by the
product would be dangerous to customers nearby, set the product so it will not
move while being operated.