Senco SFW09 User manual

Senco Brands, Inc.
4270 Ivy Pointe Blvd.
Cincinnati, OH 45245
1-800-543-4596
www.senco.com
NFD84C Nov. 19, 2013, replaces June 20, 2008
Stapler
Operating Instructions
Instrucciones de Operacion
Mode d’Emploi
Warnings for the safe use of this tool are included in this manual.
Los avisos para el uso seguro de esta herramienta están incluidos en este manual.
Les consignes pour l’utilisation en toute sécurité de cet outil se trouvent dans ce manuel.
SFW09
© 2013 by Senco Brands, Inc.

TABLE OF
CONTENTS
Tool Use 2
Accessories 5
MAinTenAnce 6
TroUbleshooTing 7
specificATions 8
2
ENGLISH ESPAÑOL FRANÇAIS
TOOL USE USO DE LA HERRAMIENTA UTILISATION DE L’OUTIL
TABLA DE
MATERIAS
Uso de lA herrAMienTA 2
Accesorios 5
MAnTeniMienTo 6
idenTificAción
de fAllAs 7
especificAciones 8
TABLE DES
MATIERÈS
UTilisATion de l’oUTil 2
Accessoires 5
enTreTien 6
dépAnnAge 7
spécificATions 8
EMPLOYER’S
RESPONSIBILITIES
Employer must enforce
compliance with the safety
warnings and all other
instructions which accompany
this tool as shipped from the
manufacturer.
Keep this manual available for
use by all people assigned to
the use of this tool.
For personal safety and
proper operation of this tool,
read and understand all of
these instructions carefully.
RESPONSABILIDADES DEL
EMPLEADOR
El empleador debe hacer
cumplir las advertencias de
seguridad y todas las otras
instrucciones que acompañan
a esta herramienta como se la
despacha desde el fabricante.
Mantenga este manual
disponible para que lo usen
todas las personas destinadas a
hacer uso de esta herramienta.
Por razones de seguridad
personal y la adecuada
operación de esta herramienta,
lea y comprenda todas estas
instrucciones cuidadosamente.
RESPONSABILITÉS DE
L’EMPLOYEUR
L’employeur doit faire
appliquer les consignes
de sécurité et toutes les
autres instructions qui
accompagnent cet outil
tel qu’il est livré par son
constructeur.
Ayez ce manuel à la
disposition de toutes les
personnes chargées d’utiliser
cet outil.
Pour assurer la sécurité
personnelle et le bon emploi
de cet outil, lisez et assimilez
soigneusement toutes ces
instructions.
yRead and
understand “SAFETY
INSTRUCTIONS” manual
shipped with this tool
before using tool.
yAntes de usar la
herramienta lea y
comprenda el manual
“INSTRUCCIONES DE
SEGURIDAD” despachado
con ella.
yLisez et assimilez le
manuel “INstructions de
sécurité” livré avec cet
outil avant de l’utiliser.

3
ENGLISH ESPAÑOL FRANÇAIS
TOOL USE USO DE LA HERRAMIENTA UTILISATION DE L’OUTIL
yKeep tool pointed away
from yourself and others
and connect air to tool.
yMantenga la herramienta
apuntando en la dirección
opuesta de usted y de
otros y conecte el aire a la
manguera.
yMaintenez l’outil pointé à
l’écart d’autres personnes
et de vous-même et
raccordez l’air à l’outil.
1
2
yPara cargar:
Oprima el cerrojo
y deslice el carril
abriéndolo.
yTo Load:
Depress latch and slide
rail open.
yPour charger :
Appuyer sur le verrou et
ouvrir le rail en le tirant.
yColoque la tira de grapas
dentro del cargador. Use
solamente sujetadores
SENCO auténticos. No
cargue con el gatillo
oprimidos.
yInsérer la bande d’agrafes
dans le magasin. Utilisez
uniquement les véritables
agrafes SENCO. Veillez
à ne pas appuyer sur
la détente quand vous
chargez.
yLay strip of staples into
magazine. Use only
genuine SENCO staples.
Do not load with trigger
depressed.
yPush rail forward until it
latches.
yEmpuje el carril hacia
adelante hasta cerrario.
yPousser le rail jusqu’a
encliquetage.
yNever use a tool that leaks
air or needs repair.
yNunca use una
herramienta que tenga
escapes de aire o que
necesite reparación.
yN’utilisez jamais un outil
qui a des fuites d’air ou qui
a besoin d’être réparé.

4
ENGLISH ESPAÑOL FRANÇAIS
TOOL USE USO DE LA HERRAMIENTA UTILISATION DE L’OUTIL
1
2
To drive fasteners:
yPosition tool against work
surface and pull the trigger.
yThese tools are not
required to have a
workpiece contact. USE
CAUTION as these tools
will drive a fastener when
the trigger is pulled.
Para clavar las grapas:
yColoque la herramienta
contra la supercie de
trabajo y apretar el gatillo.
yPara estas herramientas
no se necesita un punto de
contacto con la pieza de
trabajo. SEA PRECAVIDO
ya que estas herramientas
dispararán una grapa
cuando se aprieta el gatillo.
Pour agrafer:
yPosition l’appareil contre
la surface de travail et
presser sur la gâchette.
yCes outils ne nécessitent
pas de contact avec la
pièce. FAIRE ATTENTION
car ils enfonceront une
agrafe dès que la gâchette
est actionnée.
ySi se produce un
atascamiento de las
grapas, desconecte el
suministro de aire.
ySi un enrayage se produit,
coupez l’arrivée d’air.
yShould a staple jam occur,
disconnect air supply.
y1) Appuyer sur le verrou et
2) ouvrir le rail en le tirant.
y1) Oprima el cerrojo y
2) deslice el carril
abriéndolo.
y1) Depress latch and
2) slide rail open.
yRemove staples. ySaque las grapas. yEnlever les agrafes.
1
2
yLay strip of staples onto
rail. Use only genuine
SENCO fasteners (see
Parts Chart). Do not load
with trigger depressed.
yColoque una tira de grapas
en el riel. Use solamente
grapas SENCO genuinas
(ver la Tabla de Partes). No
cargue la herramienta con
el gatillo oprimido.
yMettez une série d’agrafes
dans le chargeur. N’utilisez
que de véritable agrafes
SENCO (voir Tableau des
Pièces). N’appuyez pas
sur la détente pendant le
rechargement.
yRemueva el sujetador
atascado.
yEnlevez le projectile
coinçé.
yRemove jammed fastener.
yRelease staple door and
slide it forward.
yDestrabe la compuerta
de las grapas y deslícela
hacia adelante.
yRelâcher le pousse
agrafes et le faire glisser
vers l’avant.

5
SENCO offers a full line of
accessories for your SENCO
tools, including:
»Air Compressors
»Hose
»Couplers
»Fittings
»Safety Glasses
»Pressure Gauges
»Lubricants
»Regulators
»Filters
For more information or a
complete illustrated catalogue
of SENCO accessories,
ask your representative for
#MK336.
SENCO ofrece una línea
completa de Accesorios para
sus herramientas SENCO,
incluyendo:
»Compresores de Aire
»Manguera
»Conectores Rapidos
»Conectores
»Anteojos De Seguridad
»Manometros
»Lubricantes
»Reguladores
»Filtros
Para mas informacion ó un
pour recevoir un catalogo
completo ilustrado de los
Accesorios SENCO, pregunte
a su representante pour el
numero MK336.
SENCO offre une gamme
étendue d’accessoires pour
vos outils SENCO y compris:
»Compresseurs
»Tuyauterie exible
»Raccords
»Lunettes de sécurité
»Manomètres
»Lubriants
»Régulateurs
»Filtres
Pour plus d’informations ou
pour recevoir un catalogue
détaillé des accessoires
proposés par SENCO, prenez
contact avec votre
représentant SENCO
(référence catalogue :
#MK336).
ENGLISH ESPAÑOL FRANÇAIS
ACCESSORIES ACCESORIOS ACCESSOIRES

6
ENGLISH ESPAÑOL FRANÇAIS
MAINTENANCE MAINTENIMIENTO ENTRETIEN
yAll screws should be kept
tight. Loose screws result
in unsafe operation and
parts breakage.
yTodos los tornillos
tienen que mantenerse
apretados. Los tornillos
sueltos pueden producir
una operación no segura y
quebraduras de partes.
youtes les vis doivent être
maintenues serrées à
fond. Les vis desserrées
entraînent un manque de
sûreté du fonctionnement
et la rupture de pièces.
yWith tool disconnected,
make daily inspection to
assure free movement of
trigger. Do not use tool if
trigger sticks or binds.
yCon la herramienta
desconectada, haga
inspecciones diarias para
asegurar un movimiento
libre del disparador. No
use la herramienta si el
disparador se pegan o se
atascan.
yL’outil étant déconnecté
de l’arrivée d’air
comprimé, effectuez une
inspection journalière
pour vous assurer le libre
mouvement de la détente.
N’utilisez pas l’outil si la
détente colle ou se coince.
ySquirt SENCO pneumatic
oil (5 to 10 drops) into
the air inlet twice daily
(depending on frequency
of tool use). Other oils may
damage O-rings and other
tool parts.
yAplique aceite neumático
SENCO en la entrada
de aire dos veces al
día (dependiendo en la
frecuencia de uso 5 A
10 Gotas). Otros aceites
pueden dañar los anillos
en “O” y otras piezas de la
herramienta.
yAvec une burette, placer
5 à 10 gouttes d’huile
pneumatique dans
l’arrivée d’air deux fois
par jour (dépend de
l’intensité de l’utilisation de
l’appareil). D’autres huiles
pourraient endommager
les joints toriques et
d’autres pièces de l’outil.
yWipe tool clean daily
and inspect for wear.
Use non-ammable
cleaning solutions only
if necessary–DO NOT
SOAK.
Caution: Such solutions
may damage O-rings and
other tool parts.
yUse soluciones de
limpieza no amablés
solamente si es necesario-
NO LA REMOJE.
Precaución: Tales
soluciones pueden dañar
los empaques y otras
partes de la herramienta.
yNettoyez l’outil chaque
jour à l’aide d’un chiffon et
inspectez-le pour déceler
une éventuelle usure.
Utilisez uniquement des
solvants non inammables
en cas de nécessité-
NE LE FAITES PAS
TREMPER !
Attention : De tels produits
peuvent endommager les
joints et autres pièces de
l’appareil.
yRead and
understand “SAFETY
INSTRUCTIONS” manual
shipped with this tool
before using tool.
yAntes de usar la
herramienta lea y
comprenda el manual
“INSTRUCCIONES DE
SEGURIDAD” despachado
con ella.
yLisez et assimilez le
manuel “INstructions de
sécurité” livré avec cet
outil avant de l’utiliser.

7
SYMPTÔME
yFuite d’air près du sommet
de l’outil / fonctionnement
lent.
SOLUTION
ySerrez les vis à fond /
vériez l’alimentation en
air ou remplacer les pièces
(YK0775).
SYMPTÔME
yFuite d’air près de la base
de l’outil / retour inadéquat.
SOLUTION
ySerrez les vis à fond /
nettoyez l’outil ou remplacer
les pièces (YK0775).
SYMPTÔME
yAutres problèmes.
SOLUTION
yPrenez contact avec
SENCO.
SYMPTOM
yAir leak near top of tool /
Sluggish operation.
SOLUTION
yVerify air supply / tighten
screws or install Repair Kit
(YK0775).
SYMPTOM
yAir leak near bottom of tool
/ Poor return.
SOLUTION
yClean tool / tighten screws
or install Repair Kit
(YK0775).
SYMPTOM
SOLUTION
yContact SENCO.
yOther problems.
SÍNTOMA
yEl aire se escapa cerca
de la parte superior de la
herramienta / Operación.
lenta.
SOLUCIÓN
yApriete los tornillos /
Verique el suministro de
aire o instale de Partes
(YK0775).
SÍNTOMA
SOLUCIÓN
yEl aire se fuga cerca de
la parte inferior de la
herramienta / Mal retorno.
yApriete los tornillos / Limpié
la herramienta o instale de
Partes (YK0775).
SÍNTOMA
SOLUCIÓN
yOtros
problemas.
yPóngase en contacto
con SENCO.
WARNING
Repairs other than those
described here should be
performed only by trained,
qualied personnel. Contact
SENCO for information at
1-800-543-4596.
ALERTA
Las reparaciones, fuera de
aquellas descritas aquí,
deben de ser llevadas a
cabo solamente por personal
entrenado y calicado.
Póngase en contacto con
SENCO para información
1-800-543-4596.
AVERTISSEMENT
Les réparations autres que
celles décrites ici doivent être
réalisées uniquement par du
personnel qualié ayant reçu
la formation appropriée. Pour
toute information, prenez
contact avec SENCO par
téléphone en appelant Le
Distributeur agréé.
ENGLISH ESPAÑOL FRANÇAIS
TROUBLESHOOTING IDENTIFICACIÓN DE FALLAS DÉPANNAGE
yRead and
understand “SAFETY
INSTRUCTIONS” manual
shipped with this tool
before using tool.
yAntes de usar la
herramienta lea y
comprenda el manual
“INSTRUCCIONES DE
SEGURIDAD” despachado
con ella.
yLisez et assimilez le manuel
“INSTRUCTIONS DE
SÉCURITÉ” livré avec cet
outil avant de l’utiliser.

Pression de travail min. et max.
Consommation d’air (60 cycles par minute)
Admission d’air
Vitesse maximum (cycles par seconde)
Poids
Capacité de projectiles par magasin
Dimensions de l’outil: hauteur
Dimensions de l’outil: longueur
Dimensions de l’outil: largeur: corps de l’appareil)
Presión de operación mínima y máxima
Consumo de aire (60 ciclos por minuto)
Entrada de aire
Velocidad máxima (ciclos por segundo)
Peso
Capacidad de grapas por cargador
Tamaño de la herramienta: Altura
Tamaño de la herramienta: Longitud
Tamaño de la herramienta: Ancho (Cuerpo)
8
ENGLISH
TECHNICAL SPECIFICATIONS
Minimum to maximum operating pressure
Air Consumption (60 cycles per minute)
Air Inlet
Maximum Speed (cycles per minute)
Weight
Staple Capacity
Tool size: Height
Tool size: Length
Tool size: Width: Main Body
50–95 psi
.77 scfm
1/4in. NPT
15 (Sencomatic)
2.1 lbs.
168
6 in.
9
1/4in.
1 5/8in.
3,5–6,6 bar
21,8 liter
1/4in. NPT
15 (Sencomatic)
0,95 kg
168
152 mm
235 mm
41 mm
3,5–6,6 bar
21,8 liter
1/4in. NPT
15 (Sencomatic)
0,95 kg
168
152 mm
235 mm
41 mm
50–95 psi
.77 scfm
1/4in. NPT
15 (Sencomatic)
2.1 lbs.
168
6 in.
9
1/4in.
1 5/8in.
3,5–6,6 bar
21,8 liter
1/4in. NPT
15 (Sencomatic)
0,95 kg
168
152 mm
235 mm
41 mm
50–95 psi
.77 scfm
1/4in. NPT
15 (Sencomatic)
2.1 lbs.
168
6 in.
9
1/4in.
1 5/8in.
ESPAÑOL
ESPECIFICACIONES TECNICAS
FRANÇAIS
SPECIFICATIONS TECHNIQUES

9
ENGLISH ESPAÑOL FRANÇAIS
SPECIFICATIONS ESPECIFICACIONES SPECIFICATIONS
Tool: 4C2001N
4C2071N
C04
¼ 6,4
Tool: 4C2041N
Tool: 4C2031N
1/2"
13 mm
.03
6
,91 m
m
.0275"
,70 mm
A
inches
1/4
5/16
3/8
15/32
9/16
5/8
mm
6
8
10
12
14
16
A
Code
AT04
AT05
AT06
AT08
AT09
AT10
Tool: 4C9022N
4C9071N
Tool: 4C2012N
4C2061N

Limited Warranty
SENCO® Pneumatic, DuraSpin®, Cordless Tools
& Compressors
Senco Products, Inc. (“SENCO”) designs and constructs its products using the highest standards of material and workmanship. SENCO
warrants to the original retail purchaser that the following products will be free from defects in material or workmanship for the warranty
period speci ed below:
Pnuematic tools
(both XP and Pro) Fusion Tools Combo Kit Tools GasTools
Five Years Two Years One Year Two Years
Duraspin Tools Air Compressors Multi-Blow Hand Nailers &
Stapling Hammers
One Year One Year One Year
During the warranty period (which begins on the purchase date), SENCO will repair or replace, at SENCO’s option and expense, any product or part that is defective
in materials or workmanship after examination by a SENCO Authorized Warranty Service Center, subject to the exceptions, exclusions and limitations described below.
Any replacement product or part will carry a warranty for the balance of the warranty period applicable to the replaced product or part. A DATED SALES RECEIPT OR
PROOF OF PURCHASE FROM THE ORIGINAL RETAIL PURCHASER IS REQUIRED TO MAKE A WARRANTY CLAIM. Warranty registration also is required and can
be accomplished through on-line Product Registration at www.senco.com or by completing and returning the postage paid warranty registration form included with your
Operator’s manual/parts chart information, found inside the product carton. To make a warranty claim, you must return the product, with proper receipt/proof of purchase
and return transportation charges prepaid, to a SENCO Authorized Warranty Service Center. A list of SENCO Authorized Warranty Service Centers can be found at www.
senco.com or by calling 1-800-543-4596 toll free. SENCO will perform its obligations under this warranty, within a reasonable time after approval of the warranty claim.
Wheelbarrow Compressors:
1. Subject to the exceptions, exclusions and limitations described below, SENCO warrants that the compressor pump will be free from defects in mate-
rials and workmanship for two years after the purchase date.
2. Defective parts of the compressor pump not subject to normal wear and tear will be repaired or replaced, at SENCO’s option, during the two year
warranty period. If SENCO determines that repair or replacement is not feasible, SENCO will refund the purchase price less reasonable deprecia-
tion based on actual use.
SENCO Cordless:
1. Subject to the exceptions, exclusions and limitations described below, SENCO warrants that the SENCO Cordless tool will be free from defects in
materials and workmanship for two years after the purchase date.
2. SENCO warrants that the batteries and chargers used with SENCO Cordless tools will be free from defects in material and workmanship for one
year after the purchase date.
WARRANTY EXCLUSIONS
The following warranty exclusions apply:
1. Normal wear parts are not covered under this warranty. Normal wear parts include, for example, isolators, drive belts, air  lters, rubber o-rings,
seals, driver blades, piston stops, and piston/driver assembly.
2. This warranty does not cover parts damaged due to normal wear, misapplication, misuse, accidents, operation at other than recommended speeds
or voltage (electric units only), improper storage, or damage resulting during shipping.
3. Products used in production/industrial applications as de ned by SENCO are excluded from this warranty.
4. Labor charges or loss or damage resulting from improper operation, maintenance or repairs are not covered by this warranty.
5. SENCO does not warrant the Wheelbarrow Compressor Engine/Motor, but the Compressor Engine/Motor may be covered under a warranty offered
by its manufacturer.
GENERAL WARRANTY CONDITIONS
This warranty will be honored, only if:
A. Clean, dry, regulated compressed air has been used, at air pressure not exceeding the maximum indicated on the tool casting;
B. No evidence of abuse, abnormal conditions, accident, neglect, misuse or improper modi cations or storage of the product; and
C. No Deviation from operating instructions, speci cations, and maintenance schedules exists (read Operator Manual for use, speci cations, and
maintenance instructions).
THIS WARRANTY IS THE ONLY WARRANTY ON THE PRODUCT, AND SENCO DISCLAIMS ALL OTHER WARRANTIES. ANY IMPLIED WARRANTIES WILL BE LIM-
ITED IN DURATION TO THE APPLICABLE WARRANTY PERIOD SPECIFIED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. YOUR REMEDIES ARE SOLELY AND EXCLUSIVELY AS STATED ABOVE. SENCO
SHALL IN NO EVENT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, OR SPECIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. IN NO EVENT, WHETHER
AS A RESULT OF A BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL SENCO’S LIABILITY EXCEED THE PRICE
OF THE PRODUCT WHICH HAS GIVEN RISE TO THE CLAIM OR LIABILITY. ANY LIABILITY CONNECTED WITH THE USE OF THIS PRODUCT SHALL TERMINATE
UPON THE EXPIRATION OF THE WARRANTY PERIOD SPECIFIEDABOVE. NO EMPLOYEE OR REPRESENTATIVE OF SENCO OR ANY DISTRIBUTOR OR DEALER
IS AUTHORIZED TO MAKE ANY CHANGE OR MODIFICATION TO THIS WARRANTY.
This warranty gives you speci c legal rights, and you may also have other rights which vary from state to state.
REPLACEMENT OF TOOL DUE TO NATURAL DISASTER
SENCO will replace any tool destroyed by an Act of God such as  ood, earthquake, hurricane or other disaster resulting only from the forces of nature. Such a
claim will be honored provided that such original retail purchaser had previously submitted a completed warranty registration card for the tool, and then submits
proof of ownership and an acceptable statement describing such Act of God documented by an insurance carrier, police department, or other of cial governmental
source. To obtain instructions for  ling a claim call 1-800-543-4596.
CUSTOMER SATISFACTION
One hundred percent customer satisfaction is our #1 goal. If for any reason the product does not perform to the original purchaser’s satisfaction, it can be returned
to the place of purchase within thirty days with dated sales receipt for a full refund of the purchase price.
© 2013 by SENCO BRANDS, INC.
CINCINNATI, OHIO 45244-1611 USA
www.senco.com
091013