Siemens FCI2011-U1 Guide

FCI2011-U1
NAC module (1A/2B)
Mounting
Installation
A6V10315036_d_en_--
Siemens Industry, Inc.
2018-03-16 Building Technologies Division

Legal notice
2 | 14
Siemens Industry, In
c.
A6V10315036_d_en_
--
Building Technologies Division
2018
-
03
-
16
Legal notice
Technical specifications and availability subject to change without notice.
Transmittal, reproduction, dissemination and/or editing of this document as well as
utilization of its contents and communication thereof to others without express
authorization are prohibited. Offenders will be held liable for payment of damages. All
rights created by patent grant or registration of a utility model or design patent are
reserved.
Issued by:
Siemens Industry, Inc.
Building Technologies Division
8 Fernwood Road
Florham Park, NJ 07932
Tel. [phone]
www.sbt.siemens.com/FIS
Edition: 2018-03-16
Document ID: A6V10315036_d_en_--
© Siemens Industry, Inc., 2012

3 |
14
Siemens Industry, Inc.
A6V10315036_d_en_
--
Building Technologies Division
2018
-
03
-
16
Table of contents
1Description............................................................................................... 5
2Mounting.................................................................................................. 6
3Views....................................................................................................... 7
4Pin assignments for NAC 2......................................................................... 8
4.1 X5 NAC 2 class A and NAC 2-1 and NAC 2-2 class B terminal block................. 8
5Adjusting elements for NAC 2..................................................................... 9
5.1 X602 Jumper DEGRADED MODE ENABLE/DISABLE
for NAC 2 class A or NAC 2-1 class B............................................................... 9
5.2 X603 Jumper DEGRADED MODE ENABLE/DISABLE for NAC 2-2 class B...... 9
5.3 X604, X605 and X606 NAC 2 class A/B selection jumper................................ 10
6Technical data..........................................................................................11
7FCC Statement........................................................................................12

Siemens Industry, Inc.
A6V10315036_d_en_
--
Building Technologies Division
2018
-
03
-
16
4 | 14

Description
1
5 |
14
Siemens Industry, Inc.
A6V10315036_d_en_
--
Building Technologies Division
2018
-
03
-
16
1Description
The notification appliance expansion module (NAC) provides an additional class A
circuit or 2 additional class B circuits. Each class A circuit or each of the two class B
circuits has a rating of 3 A. The header is connected to X901 on the periphery board.
The same jumpers have to be configured on the card as with the periphery board for
class A/B circuit selection and degraded mode. All jumpers must be configured, and
the module in place on X901 before power is applied to the system.
Properties
●Additional NAC circuits with 3 A power for one class A circuit or 3 A for each class
B circuit
●Protected against voltage surge and shorted outputs
●Circuit monitored for short, open, and ground fault
●Ground faults detected at <1 kΩ
●Circuits are power limited

Mounting
2
6 | 14
Siemens Industry, Inc.
A6V10315036_d_en_
--
Building Technologies Division
2018
-
03
-
16
2Mounting
The NAC module (1A/2B) FCI2011 is installed on the periphery board as shown and
screwed onto the back box. Slot X901 is also used for the releasing module.
Figure 1: Installing the NAC module on the periphery board
1Periphery board (250p) or periphery board (500p)
2 Threaded standoffs on back box
3NAC module (1A/2B) FCI2011
42x fixing screw
X901 Slot in periphery board
X5 Connection terminal on NAC module (1A/2B)
1. Plug the NAC module (3) into slot X901 on the periphery board as shown.
2. Fasten the NAC module to the threaded standoffs (2) in the back box using the two
fixing screws (4).
3. Wire up the NAC module according to the pin assignment.

Views
3
7 |
14
Siemens Industry, Inc.
A6V10315036_d_en_
--
Building Technologies Division
2018
-
03
-
16
3Views
Figure 2: Printed circuit board view for FCI2011
Element Des. Function
Connector X1 Connection to periphery board
X5 NAC 2 output
X602 DEGRADED MODE ENABLE/DISABLE for NAC 2 class A or NAC 2-1 class B
X603 DEGRADED MODE ENABLE/DISABLE for NAC 2-2 class B
X604 NAC 2 class A/B selection
X605 NAC 2 class A/B selection
X606 NAC 2 class A/B selection
X602
1
1
1
1
1
1
X603
X5
X605
X606
X604
X1

Pin assignments for NAC 2
X5 NAC 2 class A and NAC 2
-
1 and NAC 2
-
2 class B terminal block
4
8 | 14
Siemens Industry, Inc.
A6V10315036_d_en_
--
Building Technologies Division
2018
-
03
-
16
4Pin assignments for NAC 2
4.1 X5 NAC 2 class A and NAC 2-1 and NAC 2-2 class B
terminal block
Pin Designation Description
4NAC2-1 (+) Positive feed for notification appliances for NAC 2 class A or NAC 2
3NAC2-1 (-) Return feed for notification appliances for NAC 2 class A or NAC 2
2NAC2-2 (+) Positive feed for notification appliances for NAC 2 class A or NAC 2
1NAC2-2 (-) Return feed for notification appliances for NAC 2
Admissible cable cross-section: 1 x 12…18 AWG or 2 x 16…18 AWG
The jumpers must be set correctly for the class A/B selection.
Figure 3: Pin assignment for NAC circuit class A
Figure 4: Pin assignment for NAC circuit class B
* EOL resistance must be connected during non-use. EOL resistance: 2.4 kΩ, 0.5 W.
See also
2X604, X605 and X606 NAC 2 class A/B selection jumper [➙10]

Adjusting elements for NAC 2
X602 Jumper DEGRADED MODE ENABLE/DISABLE for NAC 2 class A or NAC 2
-
1 class B
5
9 |
14
Siemens Industry, Inc.
A6V10315036_d_en_
--
Building Technologies Division
2018
-
03
-
16
5Adjusting elements for NAC 2
5.1 X602 Jumper DEGRADED MODE ENABLE/DISABLE
for NAC 2 class A or NAC 2-1 class B
Errors of the power PC are displayed on the PMI & mainboard when degraded mode is
activated.
Switching on the degraded mode function of the NAC circuit 2 class A or
circuit 2-1 class B
X602 Jumper position Function Meaning
3 - 2 Disable degraded mode for
NAC 2 class A or NAC 2-1
class B.
Circuit will not activate the notification appliances if
degraded mode is activated and an alarm is present.
1 - 2 Enable degraded mode for
NAC 2 class A or NAC 2-1
class B.
Circuit will activate the notification appliances if
degraded mode is activated and an alarm is present.
5.2 X603 Jumper DEGRADED MODE ENABLE/DISABLE
for NAC 2-2 class B
Errors of the power PC are displayed on the PMI & mainboard when degraded mode is
activated.
Switching on the degraded mode function of the circuit 2-2 class B
X603 Jumper position Function Meaning
3 - 2 Disable degraded mode on
NAC 2-2 class B. Circuit will not activate the notification appliances if degraded mode is activated and an alarm is present.
1 - 2 Enable degraded mode on
NAC 2-2 class B. Circuit will activate the notification appliances if degraded mode is activated and an alarm is present.
1
2
3
1
2
3

Adjusting elements for NAC 2
X604, X605 and X606 NAC 2 c
lass A/B selection jumper
5
10 | 14
Siemens Industry, Inc.
A6V10315036_d_en_
--
Building Technologies Division
2018
-
03
-
16
5.3 X604, X605 and X606 NAC 2 class A/B selection
jumper
Class A/B setting of the additional NAC circuit
X604
X605
X606
Jumper position Function Meaning
3 - 2 Class A Configures periphery board NAC 2 for class A circuit
1 - 2 Class B Configures periphery board NAC 2-1 and NAC 2-2 for
class B circuit
The setting for class A/B must also be configured with the Engineering tool set. If the
configuration does not match the onboard jumper settings, an error will post on the
PMI.
1
2
3

Technical data
6
11 |
14
Siemens Industry, Inc.
A6V10315036_d_en_
--
Building Technologies Division
2018
-
03
-
16
6Technical data
Supply Plug strip X5
Voltage DC 24 V
Special Application for strobe loads
Regulated for non-pulsing loads
Standby operating current Max. 15 mA
Active operating current Max. 1x class A circuit or 2x class B circuits
Max. 3 A for 1x class A circuit
Max. 3 A per class B circuit
2x 3 A = 6 A for 2x class B circuits
Outputs Maximum circuit resistance 1.4 Ω@ 3.0 A
Supervised for ●Open circuit
●Short circuit
●Ground fault
Design Short-circuit protection
Voltage surge protection
Power limited

FCC Statement
7
12 | 14
Siemens Industry, Inc.
A6V10315036_d
_en_
--
Building Technologies Division
2018
-
03
-
16
7FCC Statement
WARNING
Installation and usage of equipment is not in accordance with instructi
ons manual
Radiation of radio frequency energy
Interference to radio communications
●Install and use equipment in accordance with instructions manual.
●
Read the following information.
This equipment generates, uses, and can radiate radio frequency energy and if not
installed and used in accordance with the instructions manual, may cause interference
to radio communications.
It has been tested and found to comply with the limits for a Class A computing device
pursuant to Part 15 of FCC Rules, which are designed to provide reasonable protection
against such interference when operated in a commercial environment.
Operation of this equipment in a residential area is likely to cause interference in which
case the user at his own expense will be required to take whatever measures may be
required to correct the interference.

FCC Statement
7
13 |
14
Siemens Industry, Inc.
A6V10315036_d_en_
--
Building Technologies Division
2018
-
03
-
16

Issued by
Siemens Industry, Inc.
Building Technologies Division
8 Fernwood Road
Florham Park, NJ 07932
[phone]
www.sbt.siemens.com/FIS
© Siemens Industry, Inc., 2012
Technical specifications and availability subject to change without notice.
Document ID: A6V10315036_d_en_-- SAP order no.: A5Q00050750
Edition: 2018-03-16