Siemens FDM221 User manual

FDM221, FDM223, FDM224,
FDM223H, FDM224H
Manual call points
Technical manual
Building Technologies
Fire Safety & Security Products

Liefermöglichkeiten und technische Änderungen vorbehalten.
Data and design subject to change without notice. / Supply subject to availability.
Sous réserve de modifications techniques et de la disponibilité.
© Siemens Switzerland Ltd 2004-2007
We reserve all rights in this document and in the subject thereof. By acceptance of the document the recipient acknowledges these rights
and undertakes not to publish the document nor the subject thereof in full or in part, nor to make them available to any third party without our
prior express written authorization, nor to use it for any purpose other than for which it was delivered to him.
We reserve all rights in this document and in the subject thereof. By acceptance of the document the recipient acknowledges these rights
and undertakes not to publish the document nor the subject thereof in full or in part, nor to make them available to any third party without our
prior express written authorization, nor to use it for any purpose other than for which it was delivered to him.
Nous nous réservons tous les droits sur ce document, ainsi que sur l'objet y figurant. La partie recevant ce document reconnaît ces droits et
elle s'engage à ne pas le rendre accessible à des tiers, même partiellement, sans notre autorisation écrite préalable et à ne pas l'employer
à des fins autres que celles pour lesquelles il lui a été remis.

1About this document..............................................................................5
2Safety notes.............................................................................................7
2.1 Signal words and symbols ........................................................................7
2.1.1 Classification and meaning of signal words..............................................7
2.1.2 Symbols and their meaning ......................................................................7
2.1.3 Classification and meaning of additional symbols ....................................7
2.2 Safety-relevant working instructions .........................................................8
3Overview ..................................................................................................9
4Setup and function................................................................................10
4.1 Manual call point FDM221 ......................................................................10
4.2 Manual call point FDM223 ......................................................................11
4.3 Manual call point FDM224 ......................................................................12
4.4 Diagnosis levels ......................................................................................13
4.5 Accessories.............................................................................................14
5Project planning....................................................................................15
6Installation.............................................................................................16
6.1 Preparation..............................................................................................16
6.2 Installation...............................................................................................17
6.2.1 Fixation....................................................................................................17
6.2.2 Inserting the protective cover..................................................................18
6.2.3 Electric connection..................................................................................19
7Commissioning.....................................................................................21
7.1 Localization and device test....................................................................21
7.2 Performance check .................................................................................21
8Maintenance / Troubleshooting...........................................................23
8.1 Status retrieval ........................................................................................23
8.2 General maintenance work .....................................................................23
8.3 Resetting .................................................................................................23
8.4 Replacing the glass pane........................................................................25
8.5 Spare parts..............................................................................................27
9Specifications........................................................................................28
9.1 Technical data.........................................................................................28
9.2 Dimensional drawings.............................................................................30
9.2.1 Dimensions .............................................................................................30
9.2.2 Master gauge for recesses .....................................................................30
9.3 Environmental compatibility ....................................................................30
3
Building Technologies 007002_e_en_--.doc
Fire Safety & Security Products 11.2007

4
Siemens Building Technologies 007002_e_en_--.doc
Fire & Security Products 11.2007

0BAbout this document
1 About this document
Purpose of the document
This document contains all information on the manual call points FDM221,
FDM223 and FDM224.
The consistent observance of the instructions ensures a trouble-free and safe
application.
Target group
This documentation and the instructions contained therein are intended for the
following groups of persons, who perform tasks and have the necessary
qualification:
Group of persons Activity Qualification
Product Manager (PM)
He is in charge of local product management and
is responsible for the interchange of information
between the plant supplying the equipment and
his DU for his product line. He co-ordinates the
flow of information between the individual groups
of people for the various projects.
He has had training appropriate to his function
and product range and has attended the product
manager training course.
Project Manager
The project manager is responsible for the local
project management. He co-ordinates the
schedules of all groups of people working on a
project as well as resources. He also continuously
obtains the technical information required for
project realization.
He has had the technical training appropriate to
his function and the size of a project or the
product line used in the project and has attended
the training courses for project managers at the
supplier's works.
Project Engineer
Provides the parameterization of products,
devices and systems in the DU for a specific
country or customer. He monitors the
serviceability of and gives the go-ahead for the
commissioning of products, devices and systems
at the place of installation. They are also
responsible for trouble-shooting.
He has had the training appropriate to his function
and to the products, devices and systems to be
parameterized and has attended the technical
training courses for project engineers at the
supply plant.
Installation personnel
They install product, device or system
components on site, and subsequently carry out a
general performance check.
Professional training in the field of building
automation or electrical installations.
Maintenance Personnel
They carry out all the maintenance work indicated
in the product documentation and check
equipment for total serviceability.
They have had the technical training appropriate
to their function and the product.
Reference documents
Number Name
007904 Installation for FDM221, always enclosed with the detector
007905 Installation for FDM223 and 224, always enclosed with the detector
Operational and safety regulations
Before groups of persons begin work on the system they must have read and understood the related
documents, in particular Chapter "Safety regulations".2
5
007002_e_en_--.doc
Fire Safety & Security Products 11.2007

0BAbout this document
Disregard of the safety regulations
Before they are delivered, products are tested to ensure they function correctly
when used properly. Siemens disclaims all liability for damage or injuries caused
by the incorrect application of the instructions or disregard of warnings of danger
contained in the documentation. This applies in particular to:
zPersonal injuries or damage caused by improper use and incorrect use;
zPersonal injuries or damage caused by disregarding safety instructions in the
documentation or on the product;
zPersonal injuries or damage caused by poor maintenance or a lack of
maintenance.
Symbols and their meaning
=> Result, note
'Text' Quotation, reproduced identically
-> see Cross reference
Technical terms
Term Explanation
FDnet Addressed detector line
MC-Link Maintenance and Commissioning Link
Document identification
Position Signification
Title page System names: e.g. CS1140 System
Product type: e.g. compact control unit CI1145
Purpose of the document: e.g. assembly, installation
Last page bottom left Document number
Edition date
Last page bottom left Manual
Register
Modification index
Version Date Brief description
007002_e_en_-- 11.2007 FDMH292/3-x IP64 -> IP65
007002_d_en_-- 09.2007 Standards added
Diagnosis levels changed
007002_c_en_-- 07.2007 'Technical terms' added
Corrections in 'Technical data':
- Line separator added
- Protection categories IP changed
- Standard EN54-17 added
- VdS and LPCB approvals added
007002_b_en_-- 09.2006 FDM224 included
Diagnosis levels added
007002_a_en_-- 01.2004 First edition
6
007002_e_en_--.doc
Fire Safety & Security Products 11.2007

1BSafety notes
2 Safety notes
This chapter describes the danger levels and the relevant safety regulations
applicable for the use of the products from Siemens Building Technologies. Please
read the work instructions as well as the chapter ’About this document’ before
beginning any work.
2.1 Signal words and symbols
2.1.1 Classification and meaning of signal words
The danger level – that is, the severity and probability of danger – is indicated by
the signal words listed below. Non-observance may lead to the consequences
indicated:
DANGER! Imminent danger!
zMay cause danger to life or serious bodily injury!
WARNING! Dangerous situation!
zMay cause serious bodily harm.
CAUTION! May cause dangerous situations!
zMay cause light injuries!
NOTE! Possibly harmful situation!
zMay cause damage to the product or to objects in the immediate vicinity of
the product!
2.1.2 Symbols and their meaning
The symbols listed below indicate the nature and origin of the danger.
General danger
Electrical voltage
Example for an indication of danger
The example below illustrates the appearance and form of danger warnings in our
documents.
DANGER! External voltage
Disconnect the module from the power supply.
2.1.3 Classification and meaning of additional symbols
Tips and information.
Refers to extremely important or critical decisions to be taken into account before continuing the work.
7
007002_e_en_--.doc
Fire Safety & Security Products 11.2007

1BSafety notes
2.2 Safety-relevant working instructions
Country-specific standards
The products are developed and produced in compliance with the relevant
international and European safety standards. Should additional country-specific,
local safety standards or regulations concerning project planning, installation,
operation and disposal of the product apply in the place of operation, then these
standards or regulations must also be taken into account in addition to the safety
regulations mentioned in the product documentation.
Electrical installations
DANGER!
Work on electrical installations
Work on electrical installations may only be carried out by qualified electricians
or by instructed persons working under the guidance and supervision of a
qualified electrician, in accordance with the electroctechnical regulations.
Assembly, installation, commissioning and inspection work
zIf any tools or accessories such as ladders are required, safe and suitable
devices must be used.
zThe activation of fire control installations for test purposes must not cause
damage to the system or parts thereof.
zFire control installations must only be activated after the test has been
completed and the system has been definitely handed over to the customer.
zThird party systems or devices must only be activated in the presence of the
responsible person.
Modifications to the system design and the products
Modifications to a system or to individual products may cause faults or
malfunctioning. Please request written approval from us and the relevant
authorities concerning in-tended system modifications and system extensions.
Modules and spare parts
Locally procured modules and spare parts must comply with the technical
specifica-tions laid down by the manufacturer. This compliance is always ensured
for original spare parts supplied by us.
8
007002_e_en_--.doc
Fire Safety & Security Products 11.2007

2BOverview
3 Overview
Manual call point FDM221
Housing FDMH291-x Manual call point FDM223 Housing FDMH293-x Manual call point FDM224 Housing FDMH293-x
The manual call points consist of a housing and a call point unit. They have the
following features:
zIndividual call point addressing
zIndication of the condition (Alarm, localization or test) by means of a dichromatic
LED
zIntegrated line separation function
zCommunication via FDnet
9
007002_e_en_--.doc
Fire Safety & Security Products 11.2007

3BSetup and function
4 Setup and function
4.1 Manual call point FDM221
The manual call point FDM221 triggers alarm when the glass pane is pushed in
(direct operation). The alarm is immediately transmitted to the control panel.
6
7
1
5
8
2
4
3
Legend
1 Housing bottom
2 LED
3 Switching unit
4 Terminals
5 Switching lever for test activation
6 Key with double function: Function test and opening housing
7 Alarm actuator (hammer)
8 Glass
10
007002_e_en_--.doc
Fire Safety & Security Products 11.2007

3BSetup and function
4.2 Manual call point FDM223
The manual call point FDM223 triggers alarm when the glass pane is pushed in
and the alarm button is pressed (indirect operation). The alarm is immediately
transmitted to the control panel.
143
6
5
27
Legend
1 Housing bottom
2 Switching unit
3 Terminals
4 Stopping lever
5 Alarm button
6 LED
7 Glass
11
007002_e_en_--.doc
Fire Safety & Security Products 11.2007

3BSetup and function
4.3 Manual call point FDM224
The manual call point FDM224 triggers alarm when the glass pane is pushed in
(direct operation). The alarm is immediately transmitted to the control panel.
To reset the manual call point FDM224 after an alarm, a new glass pane must be
inserted.
1 2 3
56 4
Legend
1 Housing bottom
2 Switching unit
3 Terminals
4 Glass
5 LED
6 Alarm button
12
007002_e_en_--.doc
Fire Safety & Security Products 11.2007

3BSetup and function
4.4 Diagnosis levels
The detector largely auto-monitors its function.
The following diagnosis levels are derived from the different control measurings:
zNormal
zExchange required
zFault
Details see table below.
When a fatal error occurs, which makes the proper function of the detector
impossible, a fault message is signalled. To remedy the cause, additional
information is available in the detector. This information may be displayed by e.g.
the detector exchanger and tester FDUD29x (details see Operation Detector
exchanger and tester, doc. nos. 007227 and 009718).
Indication on the detector
exchanger and tester Signification Actions
'No Deviation' Normal, no fault is present
The detector is fully functional
none
'needed excha.' * Exchange required
Button monitoring outside the tolerance
Replace detector
Fault is present
– Alarming is no longer ensured
– Button monitoring outside the tolerance
or impaired by extraneous influences
Replace detector
Supply error – Check detector line voltage
– Replace detector
Software error (Watchdog error) Replace detector
Storage error Replace detector
Any fault message
Communication error between detector
and control panel
Remedy cause
Note
The status 'Any fault message' can be displayed together with another status, e.g.
'needed excha.' (exchange required).
* Indication on the detector exchanger and tester always in English; no translation
into the country-specific language.
13
007002_e_en_--.doc
Fire Safety & Security Products 11.2007

3BSetup and function
4.5 Accessories
Module Designation Application
DMZ1197-AD Sealing For zones where there is
danger of spray water.
Note: Thanks to the
additional seal, which is
placed over the call point
unit, the manual call points
FDM223H and FDM224H
are in compliance with
protection category IP65.
DMZ1197-AC Protective cover Protection against
unintended alarm
activation with FDM223
and FDM224
FDMC291 Protective cover Protection against
unintended alarm
activation with FDM221
Cable gripper – Cable gripper with 2
cable entries
– max. cable diameter 7.8
mm
– for FDM223 or FDM224
14
007002_e_en_--.doc
Fire Safety & Security Products 11.2007

4BProject planning
5 Project planning
Compatibility
Compatible with all control panel types that support the FDnet detector line. Refer
to 'List of compatibility' (doc. no. 008331) for details.
Range of application
The manual call points are intended for use in places where a fire can be detected
by people who can manually trigger an alarm.
Place of installation
The manual call points must be installed in easily accessible places at a height of
1.3 … 1.6 m.
Environmental influences
If the manual call points are used in industry, this must be precisely clarified with
the person responsible for the project, since plastics cannot withstand some
environmental conditions. The following factors must be taken into account:
Chemicals
Temperature
Moisture
15
007002_e_en_--.doc
Fire Safety & Security Products 11.2007

5BInstallation
6 Installation
6.1 Preparation
Depending on the cabling (recessed or surface cabling), the housing must be
prepared for inserting the cables.
FDM221
1. Break out the key from the housing cover.
2. Press the two key knobs into the recesses (see figure below).
3. Pull the lid forwards.
Keep the key in a safe place.
4. Determine the entry opening(s) in the housing:
Recess cabling: Breakout point at the back of the housing base
Surface cabling: Markings on the top and bottom of the housing for the drill
hole(s), with a diameter of max. 25 mm
5. Clamp the housing in a bench vice.
6. Drill the entry opening(s).
Danger of injury Observe the tool manufacturer's safety notes!
FDM223/FDM224
1. Pull the cover of the keyhole to the right.
2. Open the housing with the key enclosed in the delivery.
Keep the key in a safe place.
3. Determine the entry openings in the housing and break them out from the
bottom, top or rear panel.
16
007002_e_en_--.doc
Fire Safety & Security Products 11.2007

5BInstallation
6.2 Installation
6.2.1 Fixation
FDM221
1. Install the housing at a height of 1.3 …1.6 m on an even surface.
2. Pull the cables through the entry opening(s) into the housing.
3. For surface mounting, use screwed cable glands (max. M20 with nut).
FDM223/FDM224
1. Install the housing at a height of 1.3 …1.6 m on an even surface. In wet areas,
only use the screw holes marked by arrows (see figure below).
2. Pull the cables through the entry opening into the housing.
3. For surface mounting, use screwed cable glands (max. M20).
17
007002_e_en_--.doc
Fire Safety & Security Products 11.2007

5BInstallation
6.2.2 Inserting the protective cover
When a protective cover is used, proceed as follows:
1. Open the housing.
2. Place the protective cover (1) in the lid (2) (see figure below).
3. Close the housing (3) with the lid (2).
FDM221
123
FDM223/FDM224
1
2
3
18
007002_e_en_--.doc
Fire Safety & Security Products 11.2007

5BInstallation
6.2.3 Electric connection
Notes on work on electrical installations
Caution zConsider the positive and negative poles!
zAs long as a manual call point is out of service, it must be provided with a
note "OUT OF SERVICE“!
Only one wire may be connected to each terminal point; only this way is it possible
to guarantee a faultless connection over the complete life cycle.
Connection diagrams
FDM221 FDM223/FDM224
+
+
FDnet FDnet
FDnet
FDnet
FDM221
1. Connect the feeding line to the terminals in the call point unit (1), in accordance
with the connection diagram.
2. When inserting the call point unit (1) into the housing (2), pay attention to the
feeding line.
3. Place the call point unit (1) with the inscription “TOP” pointing to the top
(terminals on the right) into the housing (2) until the locking device snaps in.
4. Close the housing (2) with the lid (3).
2
1
3
19
007002_e_en_--.doc
Fire Safety & Security Products 11.2007

5BInstallation
FDM223/FDM224
1. Connect the feeding line to the terminals in the call point unit (1), in accordance
with the connection diagram.
2. When inserting the call point unit (1) into the housing (2), pay attention to the
feeding line.
3. Place the call point unit (1) into the housing (2) with the terminals pointing
upwards; then fix it with two screws.
4. In wet zones, use a seal (3) (DMZ1197-AD).
5. Close the housing (2) with the lid (4).
4
1
3
2
20
007002_e_en_--.doc
Fire Safety & Security Products 11.2007