Siemens FT2009-U1 User manual

A6V10456393_enUS_c
Siemens Industry, Inc.
2016-06-16 Building Technologies Division
FT2009-U1 / FT2009-R1
LED Annunciator-32 Zone
Product Manual
Characteristic
l2 × 32 LEDs for 32 zones alarm/supervisory/trouble event display
lDisplay of system fault and ground fault from the entire system
lCommunication with panel through UFP (individual address)
lExternal 24V DC power source required from an UL listed/recognized for fire use,
regulated, power limited power supply
lIn total, up to 8 UFP type devices connected to a fire control panel
lManually activate / deactivate NAC’s
lAcknowledge and reset events from the entire system
lSelf test function
lFlat, elegant housing
UFP
FT2008
LampTest
Reset
Acknowledge
Silenced
Trouble
GroundFault
Power
FT2008-U1
AudiblesOn
LampTest
Reset
Acknowledge
Silenced
Trouble
GroundFault
Power
FT2008-U1
AudiblesOn
FT2009
24V DC
FT2007 built-in 24V DC 24V DC
firealarmresources.com

2
Siemens Industry, Inc. A6V10456393_enUS_c
Building Technologies Division 2016-06-16
LEDs & buttons & key switch
LEDs:
No. Color Status Functions
1Red /
Yellow
On Red: indicate alarm event or NAC activation event
from the zone.
Yellow: indicate supervisory event from the zone.
2Yellow On Indicate trouble event from the zone.
3Green On The LED annunciator power.
4Yellow On Indicate trouble event from the entire system.
Also indicate FT2009 communication failure.
(supervised at fire control panel).
5Yellow On Indicate ground fault event from the entire system.
6Red On Audibles are active.
7Yellow On Audibles are silenced.
8Yellow Flash Event waiting to be acknowledged.
Off All events are acknowledged.
9Yellow On The panel can be reset.
Off The panel is reset.
Buttons:
No. Button Functions
10 Audibles On /
Silenced
Silence / Un-silence the NAC’s in the event.
11 Acknowledge Acknowledge events.
12 Reset Resets the fire control panel to quiescent condition.
13 Lamp Test Test the LEDs and local buzzer.
Key switch: The key switch is used for control of button operation.
Lock key position Function
Buttons locked.
Buttons unlocked.
Lamp Test
Reset
Acknowledge
Silenced
Trouble
Ground Fault
Power
FT2009-U1
Audibles On
1
2
3
4
5
6
7
8
9
10
11
12
13
firealarmresources.com

3
Siemens Industry, Inc. A6V10456393_enUS_c
Building Technologies Division 2016-06-16
DIP switch & EOL jumper
S601 Dip-Switch for address setting
X209 EOL jumper for setting terminal resistor
X203 / X204 Connection to UFP, power supply and grounding
Dip-switch:
8-digit Dip-switch is used for the FT2009 address setting and baud rate setting. The
first 1-4 digits are for setting FT2009 address, the 7-8 digits are for setting UFP
communication baud rate. The 5 and 6 digits are reserved for future use.
Address
DIP switch
Baud Rate
DIP switch
1 2 3 4 7 8
1On Off Off Off 9600 bps Off Off
2 Off On Off Off 19200 bps On Off
3On On Off Off 38400 bps Off On
4Off Off On Off 57600 bps On On
5On Off On Off
6Off On On Off
7On On On Off
8Off Off Off On
Connect to fire control panel FC901/FC2005, 19200 bps is required.
EOL jumper: EOL jumper is used for setting terminal resistor of UFP.
Jumper IN Terminal resistor is connected.
Jump OUT Terminal resistor is not connected.
S601
X209 X203
X204
firealarmresources.com

Issued by
Siemens Industry, Inc.
Building Technology Division
8 Fernwood Road
Florham Park, NJ 08932
Tel. [phone]
www.sbt.siemens.com/FIS
@2016 Siemens Industry, Inc.
Technical specifications and availability subject to change without notice.
Doc No. A6V10456393_enUS_c
Edition 2016-06-16
Dimensions
In: inch
Technical data
Operating voltage 24V DC Nominal / 18.8…27.2V DC
Operating current (quiescent) 25 mA
Activation current 105 mA
Operating temperature 32…120.2 °F
Storage temperature 14…+140 °F
Humidity ≤93 % rel.
Communication protocol UFP
Connection terminals 14…18 AWG
Color Black / Red
Operating location Indoor / dry
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Details for ordering
Type Material No. Part No. Designation Weight
FT2009-U1 S54400-A145-A1 101592281 LED annunciator-32 Zone, black 3.748 lb
FT2009-R1 S54400-A146-A1 101592282 LED annunciator-32 Zone, red 3.748 lb
·For Canadian applications, the “FT2009-U1”/“FT2009-R1” is deemed supplementary and can be used for display
only. It must be housed in a ULC-S527 approved, locked, enclosure.
·Not approved for UL/ULC MNS applications.
11.417
7.362
1.949
firealarmresources.com