Siemens TZC-8B User manual

Siemens Industry, Inc.
BuildingTechnologies Division
P/N 315-034110-6
A24205-A334-B821
Telephone Zone Card
Installation Instructions
Model TZC-8B
INTRODUCTION The ModelTZC-8B Telephone Zone Card from Siemens
Industry, Inc., provides a way for emergency response
personnel located throughout a building to speak with one
another during emergency situations.The card is located in
any FireFinder-XLS enclosure and is connected to jacks or Fire
Fighter’s Telephone Stations located throughout the building.
Portable phones (Models PFT and PFT-P) that plug into
these jacks or Fire Fighter’s Telephone Stations (Model FTS)
can communicate to the Model FMT Fireman’s Master
Telephone located at the main enclosure or to telephones
connected to the system.
OPERATION Each TZC-8B module provides eight telephone zones. The
TZC-8B module connects to the emergency telephones or
telephone jacks located throughout a building through the
eight telephone zones. In addition, it is also connected to
the phone riser and to the CAN bus which the system uses
to control the TZC-8B.
In normal operation, the TZC-8B monitors the inputs of the
eight zones to detect if one of the connected phones is off
hook or “jacked in”. When this is detected, theTZC-8B
transmits a message to the system via the CAN bus. The
system indicates the call on the front panel. Depending on
operator action, a message is sent back to the TZC-8B to
connect the zone through to the phone riser.
All the TZC-8B zone circuits are supervised for Class B
(Style Y) use only.
Controls and Indicators The front panel of the TZC-8B contains one reset switch, 20
LEDs, and two CAN address switches as shown in Figure 1.
A reset switch is located on the top of the front panel.
Pushing the reset switch re-initializes the TZC-8B operation.
CAN
TRBL
TRBL
TRBL
TRBL
ZONE 2 ACTIVE
ZONE 6 ACTIVE
ZONE 1 ACTIVE
ZONE 5 ACTIVE
ZONE 4 ACTIVE
ZONE 8 ACTIVE
TRBL
TRBL
TRBL
TRBL
ZONE 3 ACTIVE
ZONE 7 ACTIVE
CARD FAIL
GND FAULT
CAN FAIL
RESET
POWER
TZC-8B
ONES
TENS
Figure 1
TZC-8B Telephone
Zone Card

Siemens Industry, Inc.
Building Technologies Division
P/N 315-034110-6
A24205-A334-B821
2
The LEDs follow the reset switch and their functions are defined as follows:
POWER (Green) Normally ON. When illuminated, indi-
cates that power for the TZC-8B is
applied to the card.
CARD FAIL (Yellow) Normally OFF. When illuminated, indi-
cates that the card microprocessor has
failed.
CAN FAIL (Yellow) Normally OFF. When illuminated, indicates
that the CAN communication with the
TZC-8B has terminated.
GND FAULT (Yellow) Normally OFF. When illuminated, indi-
cates that the TZC-8B has detected
either a negative or positive ground fault
on its field wiring.
ZONE 1 ACTIVE (Red) Normally OFF. When illuminated, indi-
cates that Zone 1 is active.
TROUBLE (Yellow) Normally OFF. When illuminated, indi-
cates that the TZC-8B has detected a
trouble on Zone 1 (open circuit or short
circuit).

ZONE 8 ACTIVE (Red) Normally OFF. When illuminated, indi-
cates that Zone 8 is active.
TROUBLE (Yellow) Normally OFF. When illuminated, indi-
cates that the TZC-8B has detected a
trouble on Zone 8 (open circuit or short
circuit).
PRE-INSTALLATION CAN Network Address Switch: Set the two-digit CAN network address for the
TZC-8B using the two rotary dial switches located near the bottom of the front panel.
(Refer to Figure 1 for the location of the switches.) The address selected at the front
panel of the TZC-8B must be the same as the address selected in the Zeus program-
ming tool. To set the address, turn the pointers on both of the two dials to the
numbers for the selected address. For example, if the address is 12, set the pointer
for theTENS dial to “1” and set the pointer for the ONES dial to “2”. Allowable
addresses are from 01 to 99 (leading zeros must be used).
CAN

Siemens Industry, Inc.
Building Technologies Division
P/N 315-034110-6
A24205-A334-B821
3
WIRING
Remove all system power before installation, first battery then AC. (To power up,
connect the AC first, then the battery.)
All field wiring to the TZC-8B is connected to the terminal blocks of the CC-5 card
cage slot in which it is installed (refer to Figure 2).
The top terminals (1 through 8 and 9 through 16) are connected to telephone zones 1
through 8.Terminate all unused outputs with an EOL resistor, as shown in Figure 2.
Of all the bottom terminals (17 through 24), only terminals 17 and 18 are used for
+24V connections.
The screw terminals can accommodate one 12-18 AWG or two 16-18 AWG.
Figure 2
TZC-8B Wiring Diagram
METSYSENOHPELETS'RETHGIFERIFELBITAPMOC
SEIROSSECCA
LEDOMNOITPIRCSED
STFnoitatSenohpeleTs'rethgiferiF
P-STFkl
aToThsuP-noitatSenohpeleTs'rethgiferiF
C-STFelbaCderomrA-noitatSenohpeleTs'rethgiferiF
LC-STFelbaCderomrA
-noitatSenohpeleTs'rethgiferiF
DEL&
LCP-STF,klaToThsuP-noitatSenohpeleTs'rethgiferiF
DEL&elbaCderomrA
303-
JFkcaJenohPetomeR
SS303-JFleetSsselniatS-kcaJenohPetomeR
403-JFkcaJenohPetomeR
SS403-JFleetSsselniatS-kcaJen
ohPetomeR
TFPenohpeleTs'rethgiferiFelbatroP
P-TFPklaToThsuP-enohpeleTs'rethgiferiFelbatroP
003-BFenohpeleTe
tomeRroFxobkcaBhsulF
S103-BFenohpeleTetomeRroFxobkcaBecafruS
S003-CFsexobkcaBroFrooDdekcoL-yeK
SLG-TFssalGt
nemecalpeR
NOTES
1. All wiring must be in accordance
with Article 760 of NEC or local
building codes.
2. All output circuits are power
limited to NFPA 70 per NEC 760.
3. Electrical Ratings:
Output Zone Supervisory:
35mA max @ 24VDC
4. A maximum of 10 phones can be
simultaneously connected
throughout the system.
5. An unlimited number of jacks can
be connected to each zone on the
TZC-8B.
6. 100Ωmax per zone.
7. Use twisted pair or shielded
twisted pair.
8. Terminate shield at TZC-8B only.
9. Positive or negative ground fault
detected at <10K ohms for
terminals 1-16.
12345678
910111213141516
24V+
24V–
17 18 19 20 21 22 23 24
TO
PSC-12/PSX-12
ONE SLOT OF CC-5
ZONE 1
+
-
OUT
RETURN
ZONE 2
+
-
OUT
RETURN
ZONE 3
+
-
OUT
RETURN
ZONE 4
+
-
OUT
RETURN
ZONE 8
*
*
*
*
*
****
ZONE 7
+
+
-
-
OUT
RETURN
IF NOT USED,
WIRE AS SHOWN
END OF LINE RESISTOR
10K, ¼W, P/N 140-034726
IN CANADA, MOUNT USING MODEL EL-33.
ZONE 5
+
-
-
OUT
RETURN
ZONE 6
+
OUT
RETURN
Denotes connection to
any of the following:
FTS
FTS-P
FTS-C
FTS-CL
FTS-PCL
FJ-303
FJ-303SS
FJ-304
FJ-304SS

P/N 315-034110-6
A24205-A334-B821
INSTALLATION The TZC-8B plugs perpendicularly into one slot in the CC-5 card-cage via two
96-pin DIN connectors and can occupy any slot in the card cage.
Insert the TZC-8B card into the card guides rightside up
(lettering on the front panel is legible).
Slide the card in until the card edge connectors contact
the receptacles on the motherboard.
Verify that the DIN connectors of the card and the card-
cage aligned properly. The card can only plug in one
direction to the card cage, if it does not align, DO NOT
FORCE the card.
Place thumbs on the front panel adjacent to the captive
screws and gently apply even pressure on the card
until the connectors seat in the receptacles on the
motherboard.
Secure with the captive screws.
Power up the system and verify that the TZC-8B power
LED turns ON.
To Connect External Wiring Loosen the screw of the terminal by turning it counterclockwise.
Insert the wire into the side of the terminal block
Tighten the screw of the terminal block by turning it clockwise.
ELECTRICAL RATINGS
tnerruCenalPkcaBV420
tnerruCV42lanimreTwercSxaMenozevitcarepAm53+Am082
tnerruCenalPkcaBV2.60
tnerruCybdnatS
V42Am082
rewoPtuptuO
riaPkrowteNNAC
.xamkaepotkaepV8
.xamAm57
)noissimsnartgsmgnirud(
Figure 3
Installing The TZC-8B
Siemens Industry, Inc.
Building Technologies Division
Florham Park, NJ
Siemens Building Technologies, Ltd.
Fire Safety & Security Products
2 Kenview Boulevard
Brampton, Ontario L6T 5E4 Canada
Siemens Gebäudesicherheit
GmbH & Co. oHG
D-80930 München
For CE applications in Cerberus E100 systems refer to
Installation Instruction A24205-A334-B844 (English) or A24205-A334-A844 (German).