Siemens IC60 User manual

Building Technologies
Fire Safety & Security Products
IC60
User Manual
11-2006

Liefermöglichkeiten und technische Änderungen vorbehalten.
Data and design subject to change without notice. / Supply subject to availability.
Sous réserve de modifications techniques et de la disponibilité.
© 2006 Copyright by
Siemens Switzerland Ltd
Wir behalten uns alle Rechte an diesem Dokument und an dem in ihm dargestellten Gegenstand vor. Der Empfänger anerkennt diese
Rechte und wird dieses Dokument nicht ohne unsere vorgängige schriftliche Ermächtigung ganz oder teilweise Dritten zugänglich machen
oder außerhalb des Zweckes verwenden, zu dem es ihm übergeben worden ist.
We reserve all rights in this document and in the subject thereof. By acceptance of the document the recipient acknowledges these rights
and undertakes not to publish the document nor the subject thereof in full or in part, nor to make them available to any third party without our
prior express written authorization, nor to use it for any purpose other than for which it was delivered to him.
Nous nous réservons tous les droits sur ce document, ainsi que sur l'objet y figurant. La partie recevant ce document reconnaît ces droits et
elle s'engage à ne pas le rendre accessible à des tiers, même partiellement, sans notre autorisation écrite préalable et à ne pas l'employer
à des fins autres que celles pour lesquelles il lui a été remis.

3
Building Technologies 009929_a_en_--.doc
Fire Safety & Security Products 11.2006
1General.....................................................................................................4
1.1 Country specific standards........................................................................4
1.2 Security Information ..................................................................................4
1.3 Notes on graphics .....................................................................................4
1.4 EC Directives ............................................................................................5
2Operating panel.......................................................................................6
2.1 Operating panel layouts............................................................................6
2.2 Description of the Operating panel keys and indicators ...........................6
2.3 Key functions ............................................................................................8
2.3.1 Changing the LCD backlight .....................................................................8
2.3.2 Keypad button backlight............................................................................8
2.3.3 Changing the frequency of the keypad buzzer .........................................8
3Using the system ....................................................................................9
3.1 Entering the User/Installer program mode................................................9
3.1.1 Entering the program modes ....................................................................9
3.1.2 Exiting the program mode.......................................................................10
3.2 Silencing an alarm (signal horn) .............................................................10
3.3 How to arm the system before exiting ....................................................10
3.4 Arming the system while people stay at home .......................................11
3.5 Disarming the system .............................................................................12
3.6 Disarming the system, stopping and resetting outgoing alarms.............12
3.7 How to arm partitions ..............................................................................12
3.8 How to bypass zones..............................................................................13
3.9 Using a chime .........................................................................................13
3.10 Control for outputs and devices ..............................................................13
3.11 Emergency alerts ....................................................................................14
3.12 Generate a Threat or Duress..................................................................14
3.13 Messages and events .............................................................................15
3.13.1 How to read system messages...............................................................15
3.13.2 How to read trouble messages ...............................................................15
3.13.3 How to display events in the memory .....................................................16
3.14 How to change or add codes ..................................................................16
3.14.1 Change codes.........................................................................................16
3.14.2 How to add or change the user code......................................................17
3.14.3 How to delete a user code ......................................................................17
3.15 How to set time and date ........................................................................18
3.15.1 Changing the day, time and date............................................................18
4Remote control......................................................................................19
4.1 Using the remote control.........................................................................19
5Summary of the system main functions.............................................20
6Notes ......................................................................................................21
7Keyword index ......................................................................................22

General
4
Building Technologies 009929_a_en_--.doc
Fire Safety & Security Products 11.2006
1 General
This document contains significant information on the commissioning of the control
unit. The detailled product documentation is contained in the following manuals:
z009992 Safety Instructions
z009930 Installer Manual
z009905 Technical Reference Manual
z009929 User Manual
Warning Read the ‘Safety Instructions’ first before starting to work with the control
panel.
The manuals can be downloaded at:
www.siemens.com/homesecurity
This manual describes the functions corresponding to a general programmed setting of the control
panel. Nevertheless, the functions could be configured by the installer in a different way and there-
fore not be available.
1.1 Country specific standards
The products are developed and produced in compliance with the relevant interna-
tional and European safety standards. Should any additional country-specific, local
safety standards or regulations apply in the place of operation, concerning project
planning, installation, operation and disposal of the product, then these standards
or regulations must be taken into account in addition to the safety regulations men-
tioned in the product documentation.
1.2 Security Information
In the documentation, important information to be respected at any rate is marked
by the symbols indicated below. The additional signal word provides information on
the type of danger.
WARNING Keywords
Danger; Warning; Caution designate the degree of endangerment.
Useful notes are indicated by the following symbol:
Important, indicates useful notes.
1.3 Notes on graphics
Instead of pictures, the text uses symbols for the designation of the buttons. The
example below shows the graphic representation in short form.
Used keys: Example
Button Short form Text example
<ARM> Press button <ARM> on the keypad

General
5
Building Technologies 009929_a_en_--.doc
Fire Safety & Security Products 11.2006
1.4 EC Directives
The product fulfills the requirements of the EC Directive 99/5EC ‘Radio and tele-
communications terminal equipment’.
EG-Directive 99/5/EC R&TTE
The compliance with the EG Directive 99/5/EWG is accounted for by the adher-
ence to the following standards:
EMC
(Generic emission):
EN 61000-6-3
EN 55022 Cl. B
EMV
(Interference resistance):
EN 50130-4 +A1 +A2
Safety: EN 60950-1
EMC and Radio Spectrum Matters: EN 301489-3
Radio Spectrum Matters: EN 300220-3
The EC Declaration of Conformity is made available by:
Siemens Building Technologies
Fire & Security Products GmbH & Co. oHG
D-76181 Karlsruhe
Additionally the product complies with the following standards:
Analog PSTN interface TBR21
Designed according EN50131 grad 2

Operating panel
6
Building Technologies 009929_a_en_--.doc
Fire Safety & Security Products 11.2006
2 Operating panel
2.1 Operating panel layouts
1
2
3
8
10
11
12
13
14
15
16
17 18 19
5
4
6
9
7
5
11
12
13
14
15
16
4
10
1 2 3
6
9
17 18
78
19
Vertical control unit or external keypad Horizontal control unit
Tab. 1 Keypad layouts
2.2 Description of the Operating panel keys and indicators
No. Symbol Key/Indicator. Description
1
<STAY>
Internal system activated
Button: Arm in Stay mode
LED: Stay arming mode activated
2
<BYPASS>
Bypass key
Button: Bypass Zones
LED: Zone bypass indication
3
<ARM>
Arming
Button: Arm in Full Set Mode
LED: Full Set arming mode activated
4 <TROUBLE> Trouble indicator (red)
Trouble indication
5 <OK> System OK (ARM) indicator (green).
6
<UP>
arrow
Menu up or reading out messages
(Event Log)

Operating panel
7
Building Technologies 009929_a_en_--.doc
Fire Safety & Security Products 11.2006
No. Symbol Key/Indicator. Description
7
<LEFT>
arrow
Menu navigation to the left
8
<RIGHT>
arrow
Menu navigation to the right
9
<DOWN>
arrow
Menu navigation down
10
….
<0>…-<9>
Numeric keys 0 to 9 with characters A to Z
11
Zone-
<A>
Zone A key 'A'
12
Emergency
<FIRE>
Zone-A and Zone-B key / Emergency for Fire
Press the keys simultaneously for Emergency
13
Zone
<B>
Zone-B key 'B'
14
Emergency
<MEDICAL>
Zone-B key and Chime / Emergency for Medical
Press the keys simultaneously for Emergency
15
<CHIME>
<♫>
Chime key
16
Emergency
<SECURITY>
Chime and CTRL key / Emergency for Police, Security
(Hold-up)
Press the keys simultaneously for Emergency
17
<PROG>
Programming key – Start of program code
18
<ENTER>
◄┘
Enter key
19
<CTRL>
Control key
20 <Key 0..9> <CODE> PIN Code User/Installer
Tab. 2 Control unit keys and indicators

Operating panel
8
Building Technologies 009929_a_en_--.doc
Fire Safety & Security Products 11.2006
2.3 Key functions
2.3.1 Changing the LCD backlight
Increasing the LCD backlight:
Press <CTRL>followed by the <LEFT> arrow after at max. 2 seconds.
zBy holding down the <CTRL> button and repeatedly pressing the <LEFT> arrow
button the LCD backlight level can be increased to the maximum.
Reducing the LCD backlight:
zPress <CTRL> followed by the <RIGHT> arrow after at max. 2 seconds.
zBy holding down the <CTRL> button and repeatedly pressing the <RIGHT> ar-
row button the LCD backlight level can be decreased to the minimum.
2.3.2 Keypad button backlight
Increasing the keypad button backlight
zPress <CTRL> followed by the <UP> arrow after at max. 2 seconds
zBy holding down the <CTRL> button and repeatedly pressing the <UP> arrow
button the keypad LED backlight level can be increased to the maximum.
Decreasing the keypad button backlight
zPress <CTRL> followed within 2 seconds by <DOWN> arrow.
zBy holding down the <CTRL> button and repeatedly pressing the <DOWN> ar-
row button the keypad LED backlight level can be decreased to the minimum.
2.3.3 Changing the frequency of the keypad buzzer
zPress <CTRL> followed by 'A' or 'B' within 2 seconds.
ÎHold down the <CTRL> button.
ÎBy repeatedly pressing the 'A' button the frequency of the buzzer tone can be
increased.
ÎBy repeatedly pressing the 'B' button the frequency of the buzzer tone can be
decreased.

Using the system
9
Building Technologies 009929_a_en_--.doc
Fire Safety & Security Products 11.2006
3 Using the system
The system can generally be operated in two different ways:
zby navigating through the clear text menu with the arrow keys;
zby programming all functions with the special programming codes.
3.1 Entering the User/Installer program mode
There are two program mode levels , the CLIENT mode and the INSTALLER
mode. Normally the installer will give you access to the CLIENT mode so that you
can add, delete, or change the user codes.
3.1.1 Entering the program modes
<CTRL> <ARM>
Entering the Local program mode on the LCD keypad
In this mode you may program local data such as keypad names, zone names,
groups, users, languages etc.
1. Press the <CTRL> and <ARM> buttons simultaneously for 2 seconds.
ÎDISPLAY: Local Mode Kb 1 / User Name
To leave this mode, always press and hold <PROG>
To access the CLIENT mode, it is a prerequisite that the system is NOT armed
1. Press: <PROG>
2. Enter: Master/User pin code (default 147258)
3. <ENTER>
ÎDISPLAY: Client: User
If there is a single long beep at this point and the program LED does not turn on, this means that
you can not access the PROGRAM MODE with your code.

Using the system
10
Building Technologies 009929_a_en_--.doc
Fire Safety & Security Products 11.2006
Entering the Installer program mode
To access the INSTALLER mode, it is a prerequisite that the system is NOT armed
1. Press <PROG>
2. ENTER: Master/ Installer pin code (default: 258369)
3. <ENTER>
ÎDISPLAY: Installer: User
If there is a single long beep at this point and the program LED does not turn on, this means that
you can not access the PROGRAM MODE with your code.
3.1.2 Exiting the program mode
To EXIT any program mode, press <PROG> for 2 seconds.
3.2 Silencing an alarm (signal horn)
1. Enter your PIN code.
2. Press <ENTER>
ÎThe <OK> indicator goes out, the system is now disarmed.
This stops the alarm at any time and also turns off any audible sirens. The outgo-
ing signals are stopped. This is the same procedure as disarming the system
3.3 How to arm the system before exiting
Preparing the system for arming
Make sure that all zone indicators are off. All doors, exits and windows are closed
and motion in the protected area is restricted or bypassed. The system is ready to
be armed. The green indicator <OK> lights up. If one or more zone indicators are
illuminated, the open zones are indicated.
Close open zones or bypass them. Bypass any zone you cannot close. The <BYPASS> indicator
flashes indicating bypassed zone(s).
Warning Bypassed zones are not protected!
Arming the system
Before leaving the premises you must arm the system. Arming the alarm system
turns on all detectors in the zone/s that are armed.

Using the system
11
Building Technologies 009929_a_en_--.doc
Fire Safety & Security Products 11.2006
Used keys: Arming with a code
PIN
CODE
<CODE> <ENTER>
1. Enter your PIN <CODE>.
2. Press <ENTER> to arm the system.
ÎThe <OK> indicator lights up to indicate that the system is armed.
There is an exit delay prior to the system being armed. During this delay time, a slow beep sounds
to indicate that the system is not armed yet and to remind you to vacate the protected area.
The indicators may go out few seconds after exit delay times out, depending on the
installation setting.
To immediately ARM the system, press <ARM>.
Used keys: Quick Arm
<ARM>
1. Press <ARM> to arm the system.
ÎThe <OK> indicator lights up and the system is armed.
During the exit delay time, a slow beep sounds to indicate that the system is not armed yet and to
remind you to vacate the protected area
3.4 Arming the system while people stay at home
Used keys:
PIN
CODE
<STAY> PIN <ENTER>
Arming the system in Stay mode
This type of arming is used when people are present within the protected area.
Consequently, interior movements will be ignored by the system.
1. Press <STAY>.
2. Enter your PIN code.
3. Press <ENTER>
ÎThe <STAY> indicator flashes indicating that the system is now armed in Stay
mode.

Using the system
12
Building Technologies 009929_a_en_--.doc
Fire Safety & Security Products 11.2006
Quick stay arming
1. Press <STAY> to arm the system.
During the exit delay you can leave the premises. If you wish to stay, or if you do not want any-
body to enter the protected premises, you may cancel the Entry/Exit delay by pressing the <EN-
TER> key.
ÎThe system is armed immediately.
ÎThe <STAY> indicator indicates that the system is armed in stay mode. The
indicators may go out a few seconds after the exit delay is expired, depending
on the installer's setting.
3.5 Disarming the system
1. Enter the User PIN code
2. Press <ENTER> or <STAY> if enabled by the installer.
The <STAY> indicator goes off to indicate that the system is disarmed.
3.6 Disarming the system, stopping and resetting outgoing alarms
Disarming the system with the remote control
1. Press Disarm on your remote control
Stopping and resetting alarms
1. Enter your PIN code.
2. Press <ENTER>
ÎThe <OK> indicator goes off, the system is now disarmed.
This stops the alarm at any time and turns off any audible sirens. The outgoing
signals are stopped.
3.7 How to arm partitions
PIN
CODE
<ARM> PIN <ENTER>
The protected area can be grouped into two separate partitions (A or B). The sys-
tem can be grouped for the user‘s convenience to separate e.g. the offices from
the warehouse area in a business environment, or the different rooms of a private
residence, e.g. living room, bedroom, etc.
Arm Partition A or B
1. Press and hold <A> or <B> during two seconds to ARM the desired partition.
During the exit delay you can leave the premises. If you wish to stay or if you do not want anybody
to enter the protected premises, you may cancel the Entry/Exit delay by pressing the <ENTER>
key.
2. The slow beeping stops and the partition is armed immediately.
To arm partitions with the code see 3.2.
The indicators may go out after a few seconds, depending on the installer's setting

Using the system
13
Building Technologies 009929_a_en_--.doc
Fire Safety & Security Products 11.2006
3.8 How to bypass zones
Used keys:
ZONE
No:
<BYPASS> 01…16 <ENTER>
Bypass any zone that cannot be closed. You may bypass selected zones prior to
arming. This feature is also used to temporarily exclude a faulty zone requiring re-
pair from service.
1. To bypass a selected zone, press <BYPASS>
ÎThe Bypass indicator lights up to indicate that the system is in bypass mode.
2. Enter the zone number (e.g. 01, 05, 16) for one or more zones
3. , Press <ENTER>
ÎThe Bypass button flashes to indicate bypassed zone(s).
To disable the bypassing of zones, press <BYPASS>, enter the zone number (e.g. 07, 13), then
press <ENTER>
Note: Disarming means that the bypassing of all zones is automatically disabled.
3.9 Using a chime
A chime (day zone) is a detector that can be partly armed while you are at home
but working in another part of the building. It can be programmed to operate a
buzzer or light to let you know that you have a visitor.
zTo enable the Chime mode press <♫>.
zTo disable the day (chime) zone, press <♫>
3.10 Control for outputs and devices
The keypad enables you to control external devices, such as an air-conditioner or
heater. To activate or stop a device:
1. Press <CTRL>.
2. Press the number of the output. (Up to eight different outputs can be controlled
via the keypad).
3. Press <ENTER>
ÎThis activates or deactivates the selected device.
4. Press <CTRL>.
5. Press <ENTER>to return to normal mode.
.

Using the system
14
Building Technologies 009929_a_en_--.doc
Fire Safety & Security Products 11.2006
3.11 Emergency alerts
The functions of these three special keys are best programmed by your installer to
suit your individual situation. Most commonly they are used in a panic situation.
The alarms keys are:
PANIC FIRE MEDICAL
An alarm can be generated by simultaneous pressing of two buttons.
How to initiate a panic alarm
Simultaneously press <♫>and <CTRL>.
How to initiate a fire alarm
Simultaneously press <A> and <B>.
How to initiate a medical alarm
Simultaneously press <♫>and <B>.
3.12 Generate a Threat or Duress
If you are compelled to disarm the system in case of threat, you must enter the du-
ress digit before entering the user’s code in order to activate the automatic dialer.
The duress digit extends your usual code by one digit. If your code is 345 and your
duress digit is 8, entering 8345 will modify your code. The modified duress code
will disarm the system in a normal way, at the same time activating the dialer si-
lently to report a 'duress event' without arousing suspicion. (For details ask your in-
staller.)
WARNING
If this feature is installed, it must be checked by the user after installation.
Incorrect programming may lead to dangerous situations if people are under
threat.

Using the system
15
Building Technologies 009929_a_en_--.doc
Fire Safety & Security Products 11.2006
3.13 Messages and events
3.13.1 How to read system messages
Any system failure that may occur is indicated by system messages. System mes-
sages are automatically displayed and are listed in the tables below. Read the
messages and call for service if necessary.
Message Description – Action
Battery Low The backup battery status is low (charger or bat-
tery failure)
Main Failure The main power is disconnected or caused by
power outage.
Telephone Line Failure The telephone line is disconnected or disrupted
Radio Device Battery Low Replace battery of the device in account
Supervise Detector Failure Radio detector failed to communicate
Zone Inactivity Time-out No movement detected during the expected time
in that zone
Dialer Kiss-off Failure Communication failed. The phone line is available,
but the panel has not been able to establish a
connection.
Tab. 3 System messages
3.13.2 How to read trouble messages
Any failure or abnormal event that may occur is indicated by a trouble message
and the trouble indicator lights up.
Used key:
<CTRL> (MEM)
Reading messages
1. Press the < UP>-Arrow (MEM) to read out messages and other events stored in
memory.
Message Description - Action
Zone Tamper Tamper of a particular zone
System Tamper Main cabinet open or dismounted from the wall
Pendant Panic Panic alarm initiated via radio pendant (remote control)
Panic Panic alarm initiated via keyboard
Fire Fire alarm initiated via keyboard
Medical Medical alarm initiated via keyboard
Duress code used Duress digit pressed by one of the users under threat
Tab. 4 Trouble messages

Using the system
16
Building Technologies 009929_a_en_--.doc
Fire Safety & Security Products 11.2006
3.13.3 How to display events in the memory
The system memory stores the latest events.
Used keys:
<CTRL> (MEM)
1. Press the < UP> arrow (MEM) to display a list of events.
ÎThe system will display the latest event and automatically scroll to the next
one every 2.5 seconds; a beep is emitted.
2. Use the arrow keys to scroll manually.
ÎEach entry shows the type of event, date and time.
3. Press <ENTER> to cancel the memory readout.
When the message exceeds 16 characters, the display start to scroll..
3.14 How to change or add codes
3.14.1 Change codes
Enter the CLIENT mode:
1. Press: <PROG>
2. Enter: Master/User Pin Code (default 147258)
3. Press <ENTER>
ÎDISPLAY: Client: User
Change the code:
1. Press <1>
2. Press <ENTER>
3. Press <1> (<1> to change master code, <2>…<100> for user code change)
4. Press <ENTER>
Use the numeric keyboard to enter your new master code.
The code may be any combination of 1 to 6 digits.
5. Enter the code
6. Press <ENTER> to save your new code.
ÎThe new code will be indicated to you. 1 long beep indicates an unacceptable
code.
4. .Press <PROG> and < ENTER > to exit the User Code Program mode.
WARNING It is recommended to use a multi-digit code.

Using the system
17
Building Technologies 009929_a_en_--.doc
Fire Safety & Security Products 11.2006
3.14.2 How to add or change the user code
Enter the CLIENT mode:
1. Press: <PROG>
2. Enter: Master/User Pin Code (default 147258)
3. Press <ENTER>
ÎDISPLAY: Client: User
Change the code:
1. Press <1>
2. Press <ENTER>
3. Press <X> ('<X> = The user number (2 to100)
4. <ENTER>
5. Add or change the code with the numeric keyboard
6. <ENTER>
ÎIf there is an existing code already, it will be shown to you.
7. Use the numeric keyboard to enter the new code. The code may be any combi-
nation of 1 to 6 digits. Entering the new code will delete the old code.
8. Press <ENTER> to save your new code.
9. Repeat the procedure for all users.
10. Press <PROG> for two seconds to exit the Local Program mode.
3.14.3 How to delete a user code
Enter the CLIENT mode:
1. Press: <PROG>
2. Enter: Master/User Pin Code (default 147258)
3. Press <ENTER>
ÎDISPLAY: Client: User
Delete the code:
1. Press <1>
2. Press <ENTER>
3. Press <X> ('<X> = User number (2 to100)
ÎThe code will be shown to you.
4. <ENTER>
5. Press <CTRL> & <0> to delete the user code.
6. Press <ENTER> to save the change.
7. Press <PROG> for two seconds to exit program mode.

Using the system
18
Building Technologies 009929_a_en_--.doc
Fire Safety & Security Products 11.2006
3.15 How to set time and date
The alarm system has an internal clock that may be used to automatically arm or
disarm the alarm or turn outputs on or off. It is also used to identify when events
have occurred in the memory via the LCD keypad.
Should you need to change the time & date, this must be done from the CLIENT mode.
3.15.1 Changing the day, time and date
Always enter the CLIENT mode first:
1. Press: <PROG>
2. Enter: Master/User Pin Code (default 147258)
3. Press <ENTER>
ÎDISPLAY: Client: User
Changing the day:
1. Press <26>
2. <ENTER>
3. <2> <ENTER>
4. <1-7> <ENTER>
Î1-7 = current day (1 = Sun, 2 = Mon to 7 = Sat)
Changing the time:
1. Press <26>
2. <ENTER>
3. <1> <ENTER>
4. <HHMM> <ENTER>
ÎHH = Hour in 24-hour format and MM = minutes
Changing the date:
1. Press <26>
2. <ENTER>
3. <3> <ENTER>
4. <DDMMYY> <ENTER>
ÎDD =1-31 current date, MM = months 1-12, YY = year 00-99

Remote control
19
Building Technologies 009929_a_en_--.doc
Fire Safety & Security Products 11.2006
4 Remote control
4.1 Using the remote control
To use the system in a very easy way, you can operate all main functions from the
remote control. The remote control is a radio device. The system can manage up
to 16 remote controls, if all the 5 channels of each remote control are programmed.
The working distance between a remote control and a control unit may vary be-
tween 20-200m, depending on the environment.
Solid walls or steel/concrete may reduce the distance.
The remote control IRC60 is waterproof and can also be used in bathrooms.
With each use (transmission) a control signal is sent regarding the remaining bat-
tery power. When the battery is too low this will be indicated on the control unit dis-
play.
WARNING
Losing a remote control:
If you loose a remote control or when it is stolen, the respective user must
immediately be removed from the system.
Ask the installer for assistance.
Fig. 1 Remote control IRC60
Key functions
No: Symbol Key -
Indicator
Description
1
<ARM> Arming (on)
2
<STAY> Only the Internal system is activated
3
<*>
Additional function
This button may directly control an output,
e.g. light, garage door etc.
4
<DISARM> Deactivating the system (off)
5
<SOS>
PANIC/ SOS Simultaneously pressing
buttons 2 and 3 for 2sec activates the
PANIC function.
6
<LED> Lights up when transmitting
Tab. 5 Key and indicator description

Summary of the system main functions
20
Building Technologies 009929_a_en_--.doc
Fire Safety & Security Products 11.2006
5 Summary of the system main functions
The main functions of the system are listed in the table below.
Function Keys Description Notes
Full or Partition Arm <CODE> & ◄┘ Initiates full arm
Full Arm <ARM> Initiates full arm Only if enabled by installer
Disarm during exit <ARM> Disarms the system during the
exit delay
Only when slow beeping is emitted
Disarm <CODE> & ◄┘ Disarms the system Stopping alarms
Arm Partition <A> or <B> Arms partition A or B Press A or B for
2 seconds to arm the partition in account –
only if enabled by installer
Arm Stay <STAY> & <CODE> ◄┘ Initiates partial alarm when the
user is at home Only if enabled by installer
Arm Stay >STAY> Initiates partial alarm when the
user is at home
Disarm Stay <CODE> & ◄┘ Disarms the system
Disarm Stay <STAY> Disarms the system
Bypass <BYPASS> & Zone# ◄┘ Bypasses the zone # Repeats the procedure to un-bypass
zones
Initiate Panic <♫> & <CTRL> Activates emergency alert Press simultaneously during 2 seconds
Initiate Medical
Alarm
<♫> & <B> Activates emergency alert Press simultaneously during 2 seconds
Initiate Fire Alarm <A> & <B> Activates emergency alert Press simultaneously during 2 seconds
Memory <UP> Arrow Initiates display of events from
memory.
◄┘ Cancels memory readout
Displays events and automatically scrolls
to the next event after 2.5 sec. (Use arrow
key to scroll manually)
Chime Enable/disable <♫> Enable or disable chime function Holds the key for 2 sec to alternate. Only if
enabled by installer
Control <CTRL> & Device# ◄┘ Activates or deactivates outputs
and devices
Press <CTRL> for 2 seconds
Change or Add
Users code
<PROG> & <Master
CODE> ◄┘
Activates program mode to add
or change user codes
Customize keypad <CTRL> & <LEFT> arrow Enters Local Edit Program mode Press <CONTROL> and then <ARM> and
hold both simultaneously for 2 sec
Increase LCD backlight
level
<CTRL>&<STAY< Hold <>CTRL and press <STAY>
repeatedly to increase light
Decrease LCD backlight
level
<CTRL>&>BYPASS> Hold <CTRL> and press <BY-
PASS> repeatedly to decrease
light
Increase Keypad button
backlight level
<CTRL> & <UP>
arrow
Hold <CTRL> and press <UP>
arrow repeatedly to increase light
Decrease Keypad button
backlight level
<CTRL> & <DOWN>
arrow
Hold <CTRL> and press
<DOWN> arrow repeatedly to
decrease light
Increase buzzer tone <CTRL> & <A> Hold <CTRL> and press <A>
repeatedly to increase buzzer
tone
Decrease buzzer tone <CTRL> & <B> Hold <CTRL> and press <B>
repeatedly to increase buzzer
tone
Tab. 6 Summary of functions
When an operation has started incorrectly, press <ENTER> ◄┘ to exit and return to the previous
mode.
Pressing the <PROG> key for 2 sec returns back to the basic position.