Silvercrest SQWC A2 User manual

WIRELESS QI CHARGER
Operation and Safety Notes
CARGADOR INALÁMBRICO QI
Instrucciones de utilización y de seguridad
WIRELESS QI CHARGER/
CARGADOR INALÁMBRICO QI
SQWC A2
IAN 326858_1901IAN 326858_1901
Distributed by/Distribuido por:
Lidl US LLC., Arlington, VA 22202
Model No./Modelo Núm.: HG04114A-US /
HG04114B-US
Version/Versión: 08/2019
FCC ID: 2AJ9O-HG4114
Made in/Hecho en: China

US-EN Operation and Safety Notes Page 3
US-ES Instrucciones de utilización y de seguridad Página 25

US-EN 3
Description of signal words ...........Page 4
Customer service ................................Page 5
Introduction ..........................................Page 5
Intended use..........................................Page 6
Trademark notices.................................Page 6
Scope of delivery..................................Page 6
Important safety instructions........Page 7
Description of parts...........................Page 13
Technical data......................................Page 14
Before use .............................................Page 15
Operation..............................................Page 15
Storage when not in use.................Page 18
Cleaning .................................................Page 18
Troubleshooting..................................Page 19
Disposal..................................................Page 20
Three year limited warranty.........Page 21

US-EN 4
DESCRIPTION OF
SIGNAL WORDS
WARNING indicates a hazardous situation
that, if not avoided, could result in death or
serious injury.
CAUTION indicates a hazardous situation
that, if not avoided, could result in minor or
moderate injury.
NOTICE indicates information considered
important, but not hazard related (e.g.
messages related to property damage).

US-EN 5
CUSTOMER SERVICE
Visit a LIDL store for further assistance.
Please have your IAN number ready.
Call customer service at
1 [phone]
Visit the Website Customer Service
Platform at
www.lidl.com/contact-us
IAN 326858_1901
WIRELESS QI CHARGER
PIntroduction
Congratulations on your purchase. You have
selected a quality product. The instructions for use
are a part of the product. They contain important
information about the safety, use and disposal
of the product. Before using the product, please
learn about all the safety information and usage
instructions. Only use the product as described
and for the specified applications. If you lend the
product to someone else, please also give all the
instructions.

US-EN 6
Intended use
The WIRELESS QI CHARGER (hereinafter referred
to as the „Product“) is an information electronics
device. This product is only for charging mobile
devices that use Qi technology. Other devices
cannot be charged with the product. The product
is intended for private use only and not for
commercial use. The manufacturer accepts no
liability for damage resulting from unauthorised
modifications or improper use.
Trademark notices
 USB®is a registered trademark of USB
Implementers Forum, Inc.
 “Qi“ and the Qi logo mark are trademark of
the Wireless Power Consortium (WPC).
 The SilverCrest trademark and trade name is the
property of their respective owners.
 Any other names and products are trademarks
or registered trademarks of their respective
owners.
Scope of delivery
1 Wireless Qi charger
1 Instructions for use

US-EN 7
IMPORTANT SAFETY
INSTRUCTIONS
READ ALL INSTRUCTIONS. KEEP FOR FUTURE
REFERENCE. INCLUDE ALL DOCUMENTATION
WHEN PASSING THIS PRODUCT ON TO
OTHERS.
DANGER TO LIFE AND RISK OF ACCIDENT
FOR INFANTS AND CHILDREN!
Risk of suffocation!
Never leave children unsupervised with the
packaging material. The packaging materials
pose a suffocation hazard. Children frequently
underestimate the dangers. The packaging
materials are not a toy. This product is not intended
for use by persons (including children) with
reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless
they have been given supervision or instruction
concerning use of the product by a person
responsible for their safety. Children should be
supervised to ensure that they do not play with the
product.

US-EN 8
Risk of property damage
 This product does not contain any parts which
can be serviced by the user.
 Keep the product away from moisture, dripping
and splashing water!
 Do not place burning candles or other open fire
on or next to the product.
 Check the product before every use!
Discontinue use if any damage to the product or
the charging cable is detected!
 If you notice smoke or an unusual noise or odor,
unplug the product immediately and remove the
USB cable.
 Sudden temperature changes may cause
condensation inside the product. In this case,
allow the product to acclimatise for some time
before using it again to prevent short circuits!
 Do not operate the product near heat sources,
e.g. radiators or other devices emitting heat!
Do not try to open the product! It has no internal
parts requiring maintenance.

US-EN 9
Radio interference
 Never use the product on airplanes, in
hospitals, service rooms, or near medical
electronic systems. The wireless signals
transmitted could impact the functionality of
sensitive electronics.
 Keep the product at least 0.65 ft / 20 cm
from pacemakers or implantable cardioverter-
defibrillators, as the electromagnetic radiation
may impair the functionality of pacemakers.
 The radio waves transmitted could cause
interference in hearing aids.
 Do not place the product near flammable gases
or potentially explosive areas (e.g. paint shops)
with the wireless components on, as the radio
waves emitted can cause explosions and fire.
 The range of the radio waves varies by
environmental conditions. In the event of
wireless data transmission, unauthorized third
parties receiving the data cannot be excluded.
 Lidl US, LLC is not responsible for interference
with radios or televisions due to unauthorized
modification of the product. Lidl US, LLC further
assumes no liability for using or replacing
cables and products not distributed by Lidl US/

US-EN 10
LLC. The user of the product id fully responsible
for correcting interference caused by such
unauthorized modification to the product, as
well as replacement of such products.
Ensure that:
 no direct heat sources (e.g. heating) can affect
the product
 the product is not exposed to bright artificial light
 any contact with splashed and dripping
water and corrosive liquids is avoided and
the product are not operated in the vicinity of
water. In particular, the product should never be
submerged in liquid; do not place any vessels
filled with liquid, for example, vases or drinks,
on or near the product
 the product is not used in the immediate vicinity
of magnetic fields (e.g. speakers)
 no fire sources (e.g.burning candles) are placed
on or near the product
 no foreign objects penetrate the product
 the product is never subjected to extreme
temperature fluctuations as this could result in
condensation and electrical short circuits. If the
product were subjected to extreme temperature
fluctuations, however, wait (2 hours) until the

US-EN 11
product has reached ambient temperature
before use
the product is never subjected to excessive
shocks and vibrations
the connected cables are always laid in such
a manner that nobody can step on or trip over
them. There is a risk of injury
no objects are placed on a connected cable
and cables are not connected over sharp edges
because this could otherwise damage the
functionality of sensitive electronics.
Changes or modification to this product not
expressly approved by the party responsible for
compliance could void the user‘s authority to
operate the product.
This product has been tested and complies with the
limits for a Class B digital device, pursuant to Part
15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This product generates,
uses and can radiate radio frequency energy

US-EN 12
and, if not installed and used in accordance with
the instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this product causes harmful
interference to radio or television reception, which
can be determined by turning the product off
and on, the user is encouraged to try and correct
the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the product
and receiver.
•Connect the equipment to an outlet on a different
circuit than the one the receiver is connected to.
• Consult the dealer or an experienced radio / TV
technician for help.
This product complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This product may not cause harmful
interference, and (2)this product must accept any
interference received, including interference that
may cause undesired operation.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator and your
body. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.

US-EN 13
PDescription of parts
1LED indicator 3USB type A plug
2Qi charging area 4Instructions for use
1
2
3
4

US-EN 14
PTechnical data
Dimensions: 4.96 in x 4.4 in x 0.31 in
(126 mm x 112 mm x 8 mm)
Weight: 0.4 lb (180 g)
Operating temperature: 5 – 35 °C
Storage temperature: 0 – 45 °C
Humidity
(no condensation): 10 – 70 %
Cable length: 4.9 ft (1.5 m)
Input voltage/ current: 5 V 2 A
Output voltage/ current: 5 V 1 A
Wireless charging power: 5 W
OR
Input voltage/ current: 9 V 1.7 A
Output voltage/ current: 9 V 1.1 A
Wireless charging power: 10 W
Frequency band: 121.63 - 170.03 kHz
Transmitted maximum
radio frequency
power (H-field): -3.42 dBuA/m at
10m distance
Wireless charging
distance: ≤ 5 mm
NOTE: The specification and design may be
changed without notification.

US-EN 15
PBefore use
• All parts have to be unpacked and the
packaging materials have to be removed
completely.
• Before use, verify the package contents are
complete and undamaged!
POperation
ATTENTION! The usage of the product with a
PC or notebook is forbidden.
NOTE:
The product only supports devices with Qi
wireless technology.
Charge your device
1. Plug the USB plug 3into the USB port on a
suitable USB adapter (not included).

US-EN 16
2. Plug the USB adapter (not included) into an
easily accessible mains socket.
3. Place the mobile device on the Qi charging
surface. Make sure the center of the device is
aligned over the center of the Qi charging
surface 2. Charging will begin on contact. The
LED 1lights up blue when charging is active.

US-EN 17
Protective covers that protect the mobile device
may interfere with the charging process. In this
case, the mobile device must be removed from
the protective cover.
NOTE:
 The user may not see LED 1during the
charging process depending on the used
mobile device.
LED indicator 1status
The product has an LED that indicates its
operational status:
LED indicator 1Status
Blue light for 1 second, then
Green light for 1 second, then
both Blue and Green light for
1 second, then LED off
Starting process
(Boot phase)
LED off Off / Standby
Blue light Charging
Blue and Green light flashing
alternatively Input overvoltage
Blue light flashing Fault condition
Green light Full charge

US-EN 18
PStorage when not in use
Store the product in a dry environment, protected
from dust and direct sunlight.
PCleaning
 Unplug the product and remove all plugs before
cleaning!
 No acid, chafing or solvent cleaning agents
should be used or the product can be
damaged.
 Clean the outside of the product using a soft,
dry cloth!
 For tough soiling, a mild cleaning agent can be
used.
 Only use a clean, dry cloth for cleaning the
product and never use any corrosive liquids.
Use a slightly moistened cloth and a mild
cleaning agent to remove stubborn dirt.

US-EN 19
PTroubleshooting
What should I do if the LED indicator
of the product is not lit during starting
process (Boot phase)?
 Check the USB cable connection between USB
adapter (not included) and the product. The
USB cable must be firmly connected.
 Check the connection between the mains socket
and the USB adapter (not included).
 Alternatively, the user must try another mains
socket.
What should I do if the mobile device
does not get charging ?
 Check that the mobile device have Qi wireless
charging technology.
 Check the mobile device is placed horizontally
on the center position of the charging pad.
 Check that no foreign object blocking the
charging.
 Check whether the mobile device is removed
from the protective cover.
What should I do if the LED indicator
flashes Blue and Green alternatively?
 This indicates input overvoltage occurred.

US-EN 20
 Disconnect the USB connection immediately.
 Check if you use a suitable USB adapter.
What should I do if the LED indicator
flashes blue?
 This indicates a fault condition occurred.
 Disconnect the USB connection immediately.
 Check that no foreign object blocking the
charging.
 Let the product cool down for a while and try to
use it again.
PDisposal
Dispose of the packaging through your local
recycling facilities and in compliance with all
federal, state and local regulations.
b
a
Please note the package markings
regarding waste separation, indicated by
abbreviations (a) and numbers (b),
meaning: 1–7: plastics/20–22: paper
and cardboard/ 80–98: composite materials.
Contact your local waste management
authority for additional information on
how to dispose of the used product.