SloanLED Value-Line 701269-WLX-MB User manual

Value-Line
Installation Guide for 701269-WLX-MB, 701269-WSX-MB, 701269-WTX-MB, 701269-RL-MB, 701269-RS-MB
1. Tools required: Measuring tape, wire
strippers (optional: drill, screwdriver).
4. Clean Channel Letter:
Clean inside letter with
rubbing alcohol and allow
to dry.
7. Connections: Modules
may be connected in
series or parallel.
8. Cap all Unused Wires:
Strand of modules
should not be looped to
create a closed circuit.
9. Connect Power Supply to First
Module on String: See Power
Supply Install Guide for more
information regarding power
supply installation .
6. Fasteners: If desired,
modules can be secured
with #6 pan head sheet
metal screws or 1/8 in (3 mm)
aluminum rivets.
5. Peel and Stick: Using predetermined layout and LED
placement from step 3, remove tape backing and stick
 modulesintoplace.Ensuremodulesarermly
attached. (CAUTION: when handling module, avoid
pressing down directly on top of LED.)
2. Supplies Required: PLTC cable, wire
nuts, IDC connectors or butt splices and
cable ties Optional: screws and silicone.
(3M Scotchlok connectors for
European installations only.)
3. Layout: Noting can depth, stroke width
and face material, use layout guidelines
and power supply capacity charts on page
2 to determine spacing and amount of
LEDs required.
PAGE 1 OF 2
WARNING Check polarity:
All connections must be RED-TO-RED (+) and BLACK-TO-BLACK (-). Reverse polarity connections may damage LEDs and will void product warranty.
CAN DEPTH
STROKE WIDTH
3M Scotchlok connectors for
European installations only.
Not UL recognized for North
American installations.

Value-Line
Installation Guide for 701269-WLX-MB, 701269-WSX-MB, 701269-WTX-MB, 701269-RL-MB, 701269-RS-MB
PAGE 2 OF 2
Layout density guidelines for Value-Line
12 VDC Power Supply capacity chart for Value-Line
Extension of Power Supply Leads
If longer lead wire from power supply to LED modules is needed, an extension can be used. Extension should be kept as short as possible:
under 15 ft for 18 AWG UL Listed PLTC or under 50 ft for 14 AWG UL Listed PLTC. (4.6 m for 1mm² or under 15.2 m for 2.5mm²).
Troubleshooting:
Entire sign or leg does not light
after complete installation.
Checkconnectionfrompowersupplyleadtorstmodule.Makesurepolarityofconnectionsmadeatpowersupplyleadand
any jumper wire is correct. Power supply outputs should be connected RED-to-RED and BLACK-to-BLACK.
Still does not light.
Check output voltage of power supply using a voltmeter. Output voltage should be DC 12.0 V ± 0.5 V. If there is no output
voltage, have a licensed electrician check input voltage. Make sure power supply is connected correctly and getting primary
power.Ifpowersupplyisconnectedproperlyandgettingprimarypowerandthereisstillnooutputvoltage,tryadi󰀨erent
power supply.
Still does not light. If power supply is getting primary power and modules don’t light, there may be a short in secondary wiring.
Check all connections and cap all loose wires.
The beginning of a leg lights, but
entire leg does not light or lights
intermittently.
The primary cause of a portion of a Value-Line leg not lighting or lighting intermittently is a bad connection or reverse
polarity connection between modules that light and modules that don’t light. Check this connection.
One module does not light, but
all others in leg light.
Value-Line modules are designed thta if one module fails, it will not cause entire sign or leg to go out. If one module does
not light, but all others in leg do, replace this module with a new one.
Inches / millimeters on center Maximum coverage per row
Module
Color Module Type Can Depth Inches (mm)
Modules per
foot (m)
Standard Face Dark Vinyl Perforated Vinyl
Single Row Multiple Rows
N.A. EU N.A. EU N.A. EU N.A. EU N.A. EU
White
Mini ≥ 5 (125) 4 (13) 4 in 100 mm 3 in 100 mm 2 in 75 mm 5 in 125 mm 4 in 100 mm
Short ≥ 5 (125) 3 (10) 4 in 125 mm 3 in 100 mm 2 in 75 mm 5 in 125 mm 4 in 100 mm
Long ≥ 5 (125) 2 (6.5) 5 in 125 mm 4 in 100 mm 3 in 75 mm 6 in 125 mm 5 in 125 mm
Red Short ≥ 5 (125) 3 (10) 4 in 125 mm 3 in 100 mm 2 in 75 mm 5 in 125 mm 4 in 125 mm
Long ≥ 5 (125) 2 (6.5) 5 in 125 mm 4 in 100 mm 3 in 75 mm 6 in 125 mm 5 in 125 mm
Note: These guidelines are intended to provide only an approximation of Value-Line product required for your sign, assuming an optimal balance of
performance and cost. Items to consider:
1. North American (N.A.) guides are based on commonly used face materials within North America, European (EU) guides are based on face materials
commonly used within Europe.
2.ItisrecommendedthatyoursttesttheLEDdensityinasampleletter/cabinettoevaluatebrightness,uniformityandcolor.
3. LED system operating temperatures -40° C to +70° C
4. Should you have questions or require assistance in testing, please contact your SloanLED customer service representative.
Customer service and technical support
888.747.4LED (888.747.4533)
SloanLED.com • [email protected]
Europe: Customer service and technical support
[phone]
SloanLED.com • [email protected]
P/N 400747 Rev D 2017-06-08
Input Output Maximum feet / Modules
Power Supply Part # (Each) Nominal Input
Voltage
Input
Current
Power
Output
Output
Current
Red
Long
Red
Short
White
Long
White
Short
White
Mini
Self-Contained 20 W 701680 120-240 V 0.55 A 20 W 1.5 A 15 / 30 10 / 30 25 / 50 17 / 50 17 / 67
60C1 60 W 701507-60C1 100-277 V 0.80 A
60 W 4.5 A 45 / 90 30 / 90 75 / 150 50 / 150 50 / 200
60W1 60 W 701507-60W1 100-240 V 0.85 A
60W2 60 W 701507-60W2 100-277 V 0.80 A
MODW(E) 60 W 701507-MODW(E) 100-240 V 1.00 A
MOD277 60 W 701507-MOD277 277-347 V 0.50 A
120D1 120 W 701507-120D1 100-277 V 1.70 A 2 × 60 W 2 × 4.5 A 2 × 45 / 90 2 × 30 / 90 2 × 75 / 150 2 × 50 / 150 2 × 50 / 200
Power used per foot (meter) in watts 1.2 W (3.9) 1.8 W (5.9) .72 W (2.4) 1.08 W (3.5) 1.08 W (3.5)
NOTE: Each12Vcircuitmustbelimitedto5A(60W)orless.ForNorthAmericaninstallations,apowersupplythatmeetsNECClass2specicationsisrequired.