SloanLED HighLINER Instruction Manual

Tools and connections shown are for secondary connections: drill,
measuring tape, electrical tape, wire strippers, twist-on or push-in UL Listed wire connectors, tie-wraps, chalk line, junction-box, and
18 AWG UL Listed PLTC cable.
General Information:
FOR YOUR SAFETY
• Read and observe all NOTES, CAUTIONS and WARNINGS shown throughout these instructions.
• Installation of power supplies to be performed by licensed electrician only.
• Safety glasses or goggles should be worn while performing installation.
• This product is ETL listed for dry, damp and wet locations.
•
•Install to NEC, local and state regulations.
Items Provided
Tools and Accessories Recommended
(optional)(optional)
Number of luminaires required per 100 square-feet (9,29 square-meters) for open, continuously lit areas.
Minimum Illumination Intensities*(lux)†
Ceiling Height 300 lx 400 lx 500 lx 600 lx
8 ft (2,4 m) 2 334
10 ft (3,0 m) 2 334
12 ft (3,7 m) 2 34 4
1. Power Supply 2. RDL-Linear Wire Nut Housing 3. RDL-Dimmer 4. RDL-Sensor 5. Mounting Clip 6. RDL-Linear Light
* Intensity measured at standard tabletop height (30 in (760 mm) from ground)
†100 lux = 9.29 foot-candela
For complete workplace lighting requirements, see OSHA requirements - Code of Federal Regulations Title 29, Section 1926.56:
SIGN LIGHTING GRAPHICS DISPLAY
Excellence in Distribution Since 1946
2240 Yates Ave. Commerce, CA 90040 | Fax [phone] | 800.CALL IEC
(225.5432)
www.IECDelivers.com
HighLINER
LED Linear Lighting System
Installation Manual
SLO-HL-OLL
TECHNICAL DATA SHEET
Page 1 of 4
HighLINER is intended for linear lighting in storerooms, walk-in coolers, sots
and a variety of other lighting applications.
HighLINER luminaires should only be used with a SloanLED 100 Watt 24 V power supply.

Preparation for Install
Mark clip locations: Snap a chalk line on surface. Measure
22 in (560 mm) off center to left and to right determine
clip location.
WARNING: Risk of electrical shock. Locate main circuit breaker
panel, de-energize, and perform lockout/tagout prior to
a licensed electrician.
CAUTION: Power supplies should not be mounted near
any other heat generating element. Mount power supply
with two self drilling/self tapping screws through tabs in both
end caps.
CAUTION: All primary connections including grounding
must comply with NEC, local and state regulations. Have a
licensed electrician connect primary wires.
1. Install junction box and power supply: Follow
power supply instructions for installing the secondary side.
Use UL listed twist-on, push-in, wire nut or equivalent
connectors for connections. Follow connector
manufacturer’s instructions.
2. Attach mounting clips as shown in diagram: Three
mounting clips per luminaire. Use screw of appropriate
length and thread type for mounting surface, #8 or #10
(4 mm or 5 mm), pan or hex head screws. Stainless steel
screws are recommended.
44.00 in (1120 mm) Center-to-Center
22 in (560 mm)22 in (560 mm)
Install
SIGN LIGHTING GRAPHICS DISPLAY
Excellence in Distribution Since 1946
2240 Yates Ave. Commerce, CA 90040 | Fax [phone] | 800.CALL IEC
(225.5432)
www.IECDelivers.com
HighLINER
LED Linear Lighting System
Installation Manual
SLO-HL-OLL
TECHNICAL DATA SHEET
Page 2 of 4

3. Install luminaire: Orient luminaire so that the lead
wires face towards power supply and junction box. Snap
luminaire into mounting clips. Attach wires to power
supply using twist-on wire connectors or equivalent.
NOTE: If multiple luminaires are being attached to the same
power supply refer to step 5 for daisy chain instructions.
WARNING Check polarity:
All connections must be
RED-TO-RED (+) and BLACK-TO-BLACK (-). Reverse
polarity connections may damage the LEDs and will void
product warranty.
4. Install RDL-Dimmer and RDL-Sensor (optional):
Connect RDL-Dimmer to the secondary side of the power
supply. Ensure the motion sensor is aimed at the primary
task area. Cat 5 cable may be concealed as required.
5. Daisy chain as required: Up to six luminaires can be
attached to a single power supply. Multiple luminaires can
be connected at the same locations using 18 AWG UL
Listed PLTC cable and twist-on or equivalent wire
connector. Length will be determined by luminaire
placement.
6. Wire nut housing: Conceal twist-on wire connectors
using provided wire nut housing. When properly installed,
the luminaire.
Junction
Box
Sensor
RDL-Linear PS
DM
SIGN LIGHTING GRAPHICS DISPLAY
Excellence in Distribution Since 1946
2240 Yates Ave. Commerce, CA 90040 | Fax [phone] | 800.CALL IEC
(225.5432)
www.IECDelivers.com
HighLINER
LED Linear Lighting System
Installation Manual
SLO-HL-OLL
TECHNICAL DATA SHEET
Page 3 of 4

7. Turn on the system: Re-energize the power circuit after
the installation is complete. Check secondary current of
each power supply to ensure it is not overloaded per rating
on label.
Troubleshooting
Luminaire won’t light. Most likely a connector or connection problem. Check connections and voltage at the connector. It could be a loose
connection, wire or connector.
More than one luminaire
does not light.
Most likely a connection problem. Check connections where the product stops lighting. Another cause could be that the
power supply is overloaded and the secondary output circuit protection is engaged. Check how many feet/meters of
product are on each leg of the power supply. Check output current of power supply
Still does not light Replace power supply.
Luminaire is dim Check to ensure total number of lights does not exceed power supply capacity.
Input Output
Part number Nominal input
voltage
Input current Power
output
Output
voltage
Maximum number
luminaires
701895-24C 100 - 240 VAC,
50 - 60 Hz
1.4 A at 110/220 VAC
2.0 A Max
100 W 24 VDC 6
100 Watt 24 VDC power supply capacity table for RDL-Linear
Dimming controller settings
Switches 1 and 2 adjust brightness level
Switches 3 and 4 adjust dim mode brightness
Switch
1
Switch
2
Brightness level Switch
3
Switch
4
Percent of
full brightness
Off Off NA Off Off 0.0%
On Off Energy Saver On Off 12.5%
Off On Standard Off On 25.0%
On On MerchandiserMax On On 50.0%
Junction
Box
Sensor
RDL-Linear PS
DM
SIGN LIGHTING GRAPHICS DISPLAY
Excellence in Distribution Since 1946
2240 Yates Ave. Commerce, CA 90040 | Fax [phone] | 800.CALL IEC
(225.5432)
www.IECDelivers.com
HighLINER
LED Linear Lighting System
Installation Manual
SLO-HL-OLL
TECHNICAL DATA SHEET
Page 4 of 4