SMC Networks LLB4 User manual

Doc. No LV20***-OMK0003-A .
PRODUCT NAME
CLAEAN AIR MODULE
CLAEAN AIR MODULECLAEAN AIR MODULE
CLAEAN AIR MODULE
MODEL / Series / Product Number
LLB Series
LLB SeriesLLB Series
LLB Series

2
Contents
1. Safety Instructions ・・・・・・・・・・・・・・・・・・・・・・・・・P3～4
2. Clean Air Module / Precautions ・・・・・・・・・・・・・・・・・・・・P5～6
3. Specific Product Precautions・・・・・・・・・・・・・・・・・・・・・P7～10
4. Variations ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P11
5. Specifications・・・・・・・・・・・・・・・・・・・・・・・・・・・・P12～13
6． Flow-rate Characteristics・・・・・・・・・・・・・・・・・・・・・・・P14
7. Digital Flow Switch Output Specifications ・・・・・・・・・・・・・・・P15
8. Functions ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・P16
9. Additional Module Procedure ・・・・・・・・・・・・・・・・・・・・P17
10. Element Replacing Procedure ・・・・・・・・・・・・・・・・・・・・P18

These safety instructions are intended to prevent hazardous situations and/or equipment damage.
These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or
“Danger.”
They are all important
(ISO/IEC)
*1)
*1) ISO 4414:
ISO 4413:
IEC 60204
ISO 102
18
etc.
Caution
Warning
Danger
1. The compatibility of the product is the responsibility of the person who designs the
equipment or decides its
Since the product specified here is used under various operating conditions, its compatibility with specific
equipment must be decided by the person who designs the equipment or decides its specifications based on
necessary analysis and tes
The expected performance and safety assurance of the equipment will be the responsibility of the person who
has determined its compatibility with the product.
This person should also continuously review all specifications of the product referr
information, with a view to giving due consideration to any possibility of equipment failure when configuring the
equipment.
2. Only personnel with appropriate training should operate machinery and equipment.
The product specified
The assembly, operation and maintenance of machines or equipment including our products must be
performed by an operator who is appropriately trained and experienced.
3. Do not service or attempt to remove pr
confirmed.
1.
The inspection and maintenance of machinery/equipment should only be performed after measures to
prevent falling or runaway of the driven objects have been confirmed.
2.
When the product is to be
and the power from any appropriate source is cut, and read and understand the specific product
precautions
of all relevant products carefully.
3.
Before machinery/equipment is
4. Contact SMC beforehand and take special consideration of safety measures if the product is
to be used in any of the following conditions.
1.
Conditions and environments outside o
direct sunlight.
2.
Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping,
vehicles, military, medical treatment, combustion and recrea
beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or
other applications unsuitable for the standard specifications described in the product catalog.
3.
An application which could have negative effects on people, property, or animals requiring special safety
analysis.
4.
Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a
mechanical protective funct
These safety instructions are intended to prevent hazardous situations and/or equipment damage.
These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or
They are all important
*1)
, and other safety regulations.
*1) ISO 4414:
Pneumatic fluid power
ISO 4413:
Hydraulic fluid power
IEC 60204
-1:
Safety of machinery
18
-1992:
Manipulating industrial robots
Caution
Warning
Danger
1. The compatibility of the product is the responsibility of the person who designs the
equipment or decides its
Since the product specified here is used under various operating conditions, its compatibility with specific
equipment must be decided by the person who designs the equipment or decides its specifications based on
necessary analysis and tes
The expected performance and safety assurance of the equipment will be the responsibility of the person who
has determined its compatibility with the product.
This person should also continuously review all specifications of the product referr
information, with a view to giving due consideration to any possibility of equipment failure when configuring the
equipment.
2. Only personnel with appropriate training should operate machinery and equipment.
The product specified
The assembly, operation and maintenance of machines or equipment including our products must be
performed by an operator who is appropriately trained and experienced.
3. Do not service or attempt to remove pr
confirmed.
The inspection and maintenance of machinery/equipment should only be performed after measures to
prevent falling or runaway of the driven objects have been confirmed.
When the product is to be
and the power from any appropriate source is cut, and read and understand the specific product
precautions
of all relevant products carefully.
Before machinery/equipment is
4. Contact SMC beforehand and take special consideration of safety measures if the product is
to be used in any of the following conditions.
Conditions and environments outside o
direct sunlight.
Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping,
vehicles, military, medical treatment, combustion and recrea
beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or
other applications unsuitable for the standard specifications described in the product catalog.
An application which could have negative effects on people, property, or animals requiring special safety
analysis.
Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a
mechanical protective funct
Safety Instructions
These safety instructions are intended to prevent hazardous situations and/or equipment damage.
These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or
They are all important
notes for safety and must be followed in addition to International Standards
, and other safety regulations.
Pneumatic fluid power
--
General rules relating to systems
Hydraulic fluid power
--
General rules relating
Safety of machinery
--
Manipulating industrial robots
Caution
Caution
in minor or
Warning
Warning
result in
death or serious injury.
Danger
in death
or
1. The compatibility of the product is the responsibility of the person who designs the
equipment or decides its
specifications.
Since the product specified here is used under various operating conditions, its compatibility with specific
equipment must be decided by the person who designs the equipment or decides its specifications based on
necessary analysis and tes
t results.
The expected performance and safety assurance of the equipment will be the responsibility of the person who
has determined its compatibility with the product.
This person should also continuously review all specifications of the product referr
information, with a view to giving due consideration to any possibility of equipment failure when configuring the
2. Only personnel with appropriate training should operate machinery and equipment.
The product specified
here may become unsafe if handled incorrectly.
The assembly, operation and maintenance of machines or equipment including our products must be
performed by an operator who is appropriately trained and experienced.
3. Do not service or attempt to remove pr
The inspection and maintenance of machinery/equipment should only be performed after measures to
prevent falling or runaway of the driven objects have been confirmed.
When the product is to be
removed, confirm that the safety measures as mentioned above are implemented
and the power from any appropriate source is cut, and read and understand the specific product
of all relevant products carefully.
Before machinery/equipment is
4. Contact SMC beforehand and take special consideration of safety measures if the product is
to be used in any of the following conditions.
Conditions and environments outside o
Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping,
vehicles, military, medical treatment, combustion and recrea
beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or
other applications unsuitable for the standard specifications described in the product catalog.
An application which could have negative effects on people, property, or animals requiring special safety
Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a
mechanical protective funct
ion, and periodical checks to confirm proper operation.
Safety Instructions
These safety instructions are intended to prevent hazardous situations and/or equipment damage.
These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or
notes for safety and must be followed in addition to International Standards
, and other safety regulations.
General rules relating to systems
General rules relating
Electrical equipment of machines
Manipulating industrial robots
-
Safety.
Caution
indicates a hazard with a low level of risk which, if not avoided, could result
in minor or
mode
rate injury.
Warning
indicates a hazard with a
death or serious injury.
indicates a hazard with a
or
serious
injury.
1. The compatibility of the product is the responsibility of the person who designs the
specifications.
Since the product specified here is used under various operating conditions, its compatibility with specific
equipment must be decided by the person who designs the equipment or decides its specifications based on
t results.
The expected performance and safety assurance of the equipment will be the responsibility of the person who
has determined its compatibility with the product.
This person should also continuously review all specifications of the product referr
information, with a view to giving due consideration to any possibility of equipment failure when configuring the
2. Only personnel with appropriate training should operate machinery and equipment.
here may become unsafe if handled incorrectly.
The assembly, operation and maintenance of machines or equipment including our products must be
performed by an operator who is appropriately trained and experienced.
3. Do not service or attempt to remove pr
The inspection and maintenance of machinery/equipment should only be performed after measures to
prevent falling or runaway of the driven objects have been confirmed.
removed, confirm that the safety measures as mentioned above are implemented
and the power from any appropriate source is cut, and read and understand the specific product
of all relevant products carefully.
Before machinery/equipment is
restarted, take measures to prevent unexpected operation and malfunction.
4. Contact SMC beforehand and take special consideration of safety measures if the product is
to be used in any of the following conditions.
Conditions and environments outside o
f the given specifications, or use outdoors or in a place exposed to
Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping,
vehicles, military, medical treatment, combustion and recrea
beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or
other applications unsuitable for the standard specifications described in the product catalog.
An application which could have negative effects on people, property, or animals requiring special safety
Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a
ion, and periodical checks to confirm proper operation.
3
Safety Instructions
These safety instructions are intended to prevent hazardous situations and/or equipment damage.
These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or
notes for safety and must be followed in addition to International Standards
General rules relating to systems
General rules relating
to systems
Electrical equipment of machines
Safety.
indicates a hazard with a low level of risk which, if not avoided, could result
rate injury.
indicates a hazard with a
death or serious injury.
indicates a hazard with a
injury.
Warning
1. The compatibility of the product is the responsibility of the person who designs the
specifications.
Since the product specified here is used under various operating conditions, its compatibility with specific
equipment must be decided by the person who designs the equipment or decides its specifications based on
The expected performance and safety assurance of the equipment will be the responsibility of the person who
has determined its compatibility with the product.
This person should also continuously review all specifications of the product referr
information, with a view to giving due consideration to any possibility of equipment failure when configuring the
2. Only personnel with appropriate training should operate machinery and equipment.
here may become unsafe if handled incorrectly.
The assembly, operation and maintenance of machines or equipment including our products must be
performed by an operator who is appropriately trained and experienced.
3. Do not service or attempt to remove pr
oduct and machinery/equipment until safety is
The inspection and maintenance of machinery/equipment should only be performed after measures to
prevent falling or runaway of the driven objects have been confirmed.
removed, confirm that the safety measures as mentioned above are implemented
and the power from any appropriate source is cut, and read and understand the specific product
restarted, take measures to prevent unexpected operation and malfunction.
4. Contact SMC beforehand and take special consideration of safety measures if the product is
to be used in any of the following conditions.
f the given specifications, or use outdoors or in a place exposed to
Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping,
vehicles, military, medical treatment, combustion and recrea
beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or
other applications unsuitable for the standard specifications described in the product catalog.
An application which could have negative effects on people, property, or animals requiring special safety
Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a
ion, and periodical checks to confirm proper operation.
Safety Instructions
These safety instructions are intended to prevent hazardous situations and/or equipment damage.
These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or
notes for safety and must be followed in addition to International Standards
General rules relating to systems
.
to systems
.
Electrical equipment of machines
.
(Part 1:
indicates a hazard with a low level of risk which, if not avoided, could result
indicates a hazard with a
medium
level of risk which, if not avoided, could
indicates a hazard with a
high
level of risk which, if not avoided,
Warning
1. The compatibility of the product is the responsibility of the person who designs the
Since the product specified here is used under various operating conditions, its compatibility with specific
equipment must be decided by the person who designs the equipment or decides its specifications based on
The expected performance and safety assurance of the equipment will be the responsibility of the person who
This person should also continuously review all specifications of the product referr
information, with a view to giving due consideration to any possibility of equipment failure when configuring the
2. Only personnel with appropriate training should operate machinery and equipment.
here may become unsafe if handled incorrectly.
The assembly, operation and maintenance of machines or equipment including our products must be
performed by an operator who is appropriately trained and experienced.
oduct and machinery/equipment until safety is
The inspection and maintenance of machinery/equipment should only be performed after measures to
prevent falling or runaway of the driven objects have been confirmed.
removed, confirm that the safety measures as mentioned above are implemented
and the power from any appropriate source is cut, and read and understand the specific product
restarted, take measures to prevent unexpected operation and malfunction.
4. Contact SMC beforehand and take special consideration of safety measures if the product is
f the given specifications, or use outdoors or in a place exposed to
Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping,
vehicles, military, medical treatment, combustion and recrea
tion, or equipment in contact with food and
beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or
other applications unsuitable for the standard specifications described in the product catalog.
An application which could have negative effects on people, property, or animals requiring special safety
Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a
ion, and periodical checks to confirm proper operation.
Safety Instructions
These safety instructions are intended to prevent hazardous situations and/or equipment damage.
These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or
notes for safety and must be followed in addition to International Standards
(Part 1:
General requirements)
indicates a hazard with a low level of risk which, if not avoided, could result
level of risk which, if not avoided, could
level of risk which, if not avoided,
1. The compatibility of the product is the responsibility of the person who designs the
Since the product specified here is used under various operating conditions, its compatibility with specific
equipment must be decided by the person who designs the equipment or decides its specifications based on
The expected performance and safety assurance of the equipment will be the responsibility of the person who
This person should also continuously review all specifications of the product referr
information, with a view to giving due consideration to any possibility of equipment failure when configuring the
2. Only personnel with appropriate training should operate machinery and equipment.
The assembly, operation and maintenance of machines or equipment including our products must be
performed by an operator who is appropriately trained and experienced.
oduct and machinery/equipment until safety is
The inspection and maintenance of machinery/equipment should only be performed after measures to
prevent falling or runaway of the driven objects have been confirmed.
removed, confirm that the safety measures as mentioned above are implemented
and the power from any appropriate source is cut, and read and understand the specific product
restarted, take measures to prevent unexpected operation and malfunction.
4. Contact SMC beforehand and take special consideration of safety measures if the product is
f the given specifications, or use outdoors or in a place exposed to
Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping,
tion, or equipment in contact with food and
beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or
other applications unsuitable for the standard specifications described in the product catalog.
An application which could have negative effects on people, property, or animals requiring special safety
Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a
ion, and periodical checks to confirm proper operation.
These safety instructions are intended to prevent hazardous situations and/or equipment damage.
These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or
notes for safety and must be followed in addition to International Standards
General requirements)
indicates a hazard with a low level of risk which, if not avoided, could result
level of risk which, if not avoided, could
level of risk which, if not avoided,
1. The compatibility of the product is the responsibility of the person who designs the
Since the product specified here is used under various operating conditions, its compatibility with specific
equipment must be decided by the person who designs the equipment or decides its specifications based on
The expected performance and safety assurance of the equipment will be the responsibility of the person who
This person should also continuously review all specifications of the product referr
ing to its latest catalog
information, with a view to giving due consideration to any possibility of equipment failure when configuring the
2. Only personnel with appropriate training should operate machinery and equipment.
The assembly, operation and maintenance of machines or equipment including our products must be
oduct and machinery/equipment until safety is
The inspection and maintenance of machinery/equipment should only be performed after measures to
removed, confirm that the safety measures as mentioned above are implemented
and the power from any appropriate source is cut, and read and understand the specific product
restarted, take measures to prevent unexpected operation and malfunction.
4. Contact SMC beforehand and take special consideration of safety measures if the product is
f the given specifications, or use outdoors or in a place exposed to
Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping,
tion, or equipment in contact with food and
beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or
other applications unsuitable for the standard specifications described in the product catalog.
An application which could have negative effects on people, property, or animals requiring special safety
Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a
ion, and periodical checks to confirm proper operation.
These safety instructions are intended to prevent hazardous situations and/or equipment damage.
These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or
notes for safety and must be followed in addition to International Standards
indicates a hazard with a low level of risk which, if not avoided, could result
level of risk which, if not avoided, could
level of risk which, if not avoided,
will
result
1. The compatibility of the product is the responsibility of the person who designs the
Since the product specified here is used under various operating conditions, its compatibility with specific
equipment must be decided by the person who designs the equipment or decides its specifications based on
The expected performance and safety assurance of the equipment will be the responsibility of the person who
ing to its latest catalog
information, with a view to giving due consideration to any possibility of equipment failure when configuring the
2. Only personnel with appropriate training should operate machinery and equipment.
The assembly, operation and maintenance of machines or equipment including our products must be
oduct and machinery/equipment until safety is
The inspection and maintenance of machinery/equipment should only be performed after measures to
removed, confirm that the safety measures as mentioned above are implemented
and the power from any appropriate source is cut, and read and understand the specific product
restarted, take measures to prevent unexpected operation and malfunction.
4. Contact SMC beforehand and take special consideration of safety measures if the product is
f the given specifications, or use outdoors or in a place exposed to
Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping,
tion, or equipment in contact with food and
beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or
other applications unsuitable for the standard specifications described in the product catalog.
An application which could have negative effects on people, property, or animals requiring special safety
Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a
These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or
notes for safety and must be followed in addition to International Standards
indicates a hazard with a low level of risk which, if not avoided, could result
level of risk which, if not avoided, could
result
1. The compatibility of the product is the responsibility of the person who designs the
Since the product specified here is used under various operating conditions, its compatibility with specific
equipment must be decided by the person who designs the equipment or decides its specifications based on
The expected performance and safety assurance of the equipment will be the responsibility of the person who
ing to its latest catalog
information, with a view to giving due consideration to any possibility of equipment failure when configuring the
The assembly, operation and maintenance of machines or equipment including our products must be
oduct and machinery/equipment until safety is
removed, confirm that the safety measures as mentioned above are implemented
and the power from any appropriate source is cut, and read and understand the specific product
restarted, take measures to prevent unexpected operation and malfunction.
4. Contact SMC beforehand and take special consideration of safety measures if the product is
f the given specifications, or use outdoors or in a place exposed to
An application which could have negative effects on people, property, or animals requiring special safety
Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a

1.
The product is provided for use in
The product herein described is basically provided for peaceful use in manufacturing industries.
If considering using the product in other industries, consult SMC beforehand and exchange
specifications or a contract if necessary.
If anything is unclear, contact your nearest sales branch.
Limited warranty and Disclaimer/Compliance Requirements
The product used is subject to the following “Limited warranty and Disclaimer” and “Compliance
Requirements”.
Read and accept them before
Limited warranty and Disclaimer
1.
The warranty period of
delivered
Also, the product may have specified
Please
consult your nearest sales branch.
2.
For any failure or damage reported within the warranty period which is clearly our
responsibility,
a replacement product or necessary parts will be provided.
This limited warranty applies only to our product independently, and not to any other damage
incurred due to the failure of the product.
3.
Prior to using SMC products, please read and understand the warranty terms and
disclaimers
noted in the specified
∗
∗∗
∗2)
Vacuum pads are excluded from this 1 year warranty.
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
Also, even within the warranty period, the wear of a product due to
pad or failure due to the deterioration of rubber material are not covered by the limited
warranty.
Compliance Requirements
1.
The use of SMC products with production equipment for the manufacture of weapons of
mass destruction(WMD)
2.
The exports of SMC products or technology from one country to another are govemed by
the relevant security laws and regulation of the countries involved in the transaction. Prior
to the shipment of a SMC product
that export are known and f
The product is provided for use in
The product herein described is basically provided for peaceful use in manufacturing industries.
If considering using the product in other industries, consult SMC beforehand and exchange
specifications or a contract if necessary.
If anything is unclear, contact your nearest sales branch.
Limited warranty and Disclaimer/Compliance Requirements
The product used is subject to the following “Limited warranty and Disclaimer” and “Compliance
Requirements”.
Read and accept them before
Limited warranty and Disclaimer
The warranty period of
delivered
,whichever is first
Also, the product may have specified
consult your nearest sales branch.
For any failure or damage reported within the warranty period which is clearly our
responsibility,
a replacement product or necessary parts will be provided.
This limited warranty applies only to our product independently, and not to any other damage
incurred due to the failure of the product.
Prior to using SMC products, please read and understand the warranty terms and
disclaimers
noted in the specified
Vacuum pads are excluded from this 1 year warranty.
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
Also, even within the warranty period, the wear of a product due to
pad or failure due to the deterioration of rubber material are not covered by the limited
warranty.
Compliance Requirements
The use of SMC products with production equipment for the manufacture of weapons of
mass destruction(WMD)
The exports of SMC products or technology from one country to another are govemed by
the relevant security laws and regulation of the countries involved in the transaction. Prior
to the shipment of a SMC product
that export are known and f
Safety Instructions
The product is provided for use in
The product herein described is basically provided for peaceful use in manufacturing industries.
If considering using the product in other industries, consult SMC beforehand and exchange
specifications or a contract if necessary.
If anything is unclear, contact your nearest sales branch.
Limited warranty and Disclaimer/Compliance Requirements
The product used is subject to the following “Limited warranty and Disclaimer” and “Compliance
Read and accept them before
using the product.
Limited warranty and Disclaimer
The warranty period of
the product is 1 year in service or 1.5 years after the product is
,whichever is first
.
∗
∗∗
∗
Also, the product may have specified
consult your nearest sales branch.
For any failure or damage reported within the warranty period which is clearly our
a replacement product or necessary parts will be provided.
This limited warranty applies only to our product independently, and not to any other damage
incurred due to the failure of the product.
Prior to using SMC products, please read and understand the warranty terms and
noted in the specified
catalog for the particular products.
Vacuum pads are excluded from this 1 year warranty.
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
Also, even within the warranty period, the wear of a product due to
pad or failure due to the deterioration of rubber material are not covered by the limited
Compliance Requirements
The use of SMC products with production equipment for the manufacture of weapons of
mass destruction(WMD)
or any other weapon is strictly prohibited.
The exports of SMC products or technology from one country to another are govemed by
the relevant security laws and regulation of the countries involved in the transaction. Prior
to the shipment of a SMC product
that export are known and f
Safety Instructions
The product is provided for use in
manufacturing industries.
The product herein described is basically provided for peaceful use in manufacturing industries.
If considering using the product in other industries, consult SMC beforehand and exchange
specifications or a contract if necessary.
If anything is unclear, contact your nearest sales branch.
Limited warranty and Disclaimer/Compliance Requirements
The product used is subject to the following “Limited warranty and Disclaimer” and “Compliance
using the product.
Limited warranty and Disclaimer
the product is 1 year in service or 1.5 years after the product is
∗
∗∗
∗
2)
Also, the product may have specified
consult your nearest sales branch.
For any failure or damage reported within the warranty period which is clearly our
a replacement product or necessary parts will be provided.
This limited warranty applies only to our product independently, and not to any other damage
incurred due to the failure of the product.
Prior to using SMC products, please read and understand the warranty terms and
catalog for the particular products.
Vacuum pads are excluded from this 1 year warranty.
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
Also, even within the warranty period, the wear of a product due to
pad or failure due to the deterioration of rubber material are not covered by the limited
Compliance Requirements
The use of SMC products with production equipment for the manufacture of weapons of
or any other weapon is strictly prohibited.
The exports of SMC products or technology from one country to another are govemed by
the relevant security laws and regulation of the countries involved in the transaction. Prior
to the shipment of a SMC product
to another country, assure that all local rules goveming
that export are known and f
ollowed.
ollowed.ollowed.
ollowed.
4
Safety Instructions
Caution
manufacturing industries.
The product herein described is basically provided for peaceful use in manufacturing industries.
If considering using the product in other industries, consult SMC beforehand and exchange
If anything is unclear, contact your nearest sales branch.
Limited warranty and Disclaimer/Compliance Requirements
The product used is subject to the following “Limited warranty and Disclaimer” and “Compliance
using the product.
Limited warranty and Disclaimer
the product is 1 year in service or 1.5 years after the product is
Also, the product may have specified
durability, running distance or replacement parts.
For any failure or damage reported within the warranty period which is clearly our
a replacement product or necessary parts will be provided.
This limited warranty applies only to our product independently, and not to any other damage
incurred due to the failure of the product.
Prior to using SMC products, please read and understand the warranty terms and
catalog for the particular products.
Vacuum pads are excluded from this 1 year warranty.
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
Also, even within the warranty period, the wear of a product due to
pad or failure due to the deterioration of rubber material are not covered by the limited
The use of SMC products with production equipment for the manufacture of weapons of
or any other weapon is strictly prohibited.
The exports of SMC products or technology from one country to another are govemed by
the relevant security laws and regulation of the countries involved in the transaction. Prior
to another country, assure that all local rules goveming
Safety Instructions
Caution
manufacturing industries.
The product herein described is basically provided for peaceful use in manufacturing industries.
If considering using the product in other industries, consult SMC beforehand and exchange
If anything is unclear, contact your nearest sales branch.
Limited warranty and Disclaimer/Compliance Requirements
The product used is subject to the following “Limited warranty and Disclaimer” and “Compliance
the product is 1 year in service or 1.5 years after the product is
durability, running distance or replacement parts.
For any failure or damage reported within the warranty period which is clearly our
a replacement product or necessary parts will be provided.
This limited warranty applies only to our product independently, and not to any other damage
Prior to using SMC products, please read and understand the warranty terms and
catalog for the particular products.
Vacuum pads are excluded from this 1 year warranty.
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
Also, even within the warranty period, the wear of a product due to
pad or failure due to the deterioration of rubber material are not covered by the limited
The use of SMC products with production equipment for the manufacture of weapons of
or any other weapon is strictly prohibited.
The exports of SMC products or technology from one country to another are govemed by
the relevant security laws and regulation of the countries involved in the transaction. Prior
to another country, assure that all local rules goveming
Safety Instructions
manufacturing industries.
The product herein described is basically provided for peaceful use in manufacturing industries.
If considering using the product in other industries, consult SMC beforehand and exchange
Limited warranty and Disclaimer/Compliance Requirements
The product used is subject to the following “Limited warranty and Disclaimer” and “Compliance
the product is 1 year in service or 1.5 years after the product is
durability, running distance or replacement parts.
For any failure or damage reported within the warranty period which is clearly our
This limited warranty applies only to our product independently, and not to any other damage
Prior to using SMC products, please read and understand the warranty terms and
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
Also, even within the warranty period, the wear of a product due to
pad or failure due to the deterioration of rubber material are not covered by the limited
The use of SMC products with production equipment for the manufacture of weapons of
or any other weapon is strictly prohibited.
The exports of SMC products or technology from one country to another are govemed by
the relevant security laws and regulation of the countries involved in the transaction. Prior
to another country, assure that all local rules goveming
The product herein described is basically provided for peaceful use in manufacturing industries.
If considering using the product in other industries, consult SMC beforehand and exchange
Limited warranty and Disclaimer/Compliance Requirements
The product used is subject to the following “Limited warranty and Disclaimer” and “Compliance
the product is 1 year in service or 1.5 years after the product is
durability, running distance or replacement parts.
For any failure or damage reported within the warranty period which is clearly our
This limited warranty applies only to our product independently, and not to any other damage
Prior to using SMC products, please read and understand the warranty terms and
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
Also, even within the warranty period, the wear of a product due to
the use of the vacuum
pad or failure due to the deterioration of rubber material are not covered by the limited
The use of SMC products with production equipment for the manufacture of weapons of
The exports of SMC products or technology from one country to another are govemed by
the relevant security laws and regulation of the countries involved in the transaction. Prior
to another country, assure that all local rules goveming
The product herein described is basically provided for peaceful use in manufacturing industries.
If considering using the product in other industries, consult SMC beforehand and exchange
Limited warranty and Disclaimer/Compliance Requirements
The product used is subject to the following “Limited warranty and Disclaimer” and “Compliance
the product is 1 year in service or 1.5 years after the product is
durability, running distance or replacement parts.
For any failure or damage reported within the warranty period which is clearly our
This limited warranty applies only to our product independently, and not to any other damage
Prior to using SMC products, please read and understand the warranty terms and
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
the use of the vacuum
pad or failure due to the deterioration of rubber material are not covered by the limited
The use of SMC products with production equipment for the manufacture of weapons of
The exports of SMC products or technology from one country to another are govemed by
the relevant security laws and regulation of the countries involved in the transaction. Prior
to another country, assure that all local rules goveming
If considering using the product in other industries, consult SMC beforehand and exchange
The product used is subject to the following “Limited warranty and Disclaimer” and “Compliance
the product is 1 year in service or 1.5 years after the product is
durability, running distance or replacement parts.
For any failure or damage reported within the warranty period which is clearly our
This limited warranty applies only to our product independently, and not to any other damage
Prior to using SMC products, please read and understand the warranty terms and
the use of the vacuum
pad or failure due to the deterioration of rubber material are not covered by the limited
The use of SMC products with production equipment for the manufacture of weapons of
The exports of SMC products or technology from one country to another are govemed by
the relevant security laws and regulation of the countries involved in the transaction. Prior
to another country, assure that all local rules goveming

5

6

7

8

9

10

11

12
付表 2 5/5

13

14

15

16

17

18

19
Revision history
A: Creating a new chart by changing
specifications
4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN
Tel: + 81 3 5207 8249 Fax: [phone]
URL http://www.smcworld.com
Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer.
© 2018 SMC Corporation All Rights Reserved