Snom D735 User manual

Snom D735 User's Manual
Ver1.0.1 May 8 2019

2
Thank you for purchasing SnomD735.
Make sure and acknowledge that you have read this manual before using SnomD735.
Package Contents:
1.Main Case
2.Handset
3.Handset Cable
4.LAN cable
5.Quick Start Guide manual
6.AC Adapter
Disclaimer
* This document is subject to change without prior notice.
* A possibility of noise, broken voice, or disconnection may occur because of customers’ or our network environment.
We cannot guarantee the quality of voice.
* The company assumes no responsibility on the difference of call or voice quality when the hearing acuity of
individuals is concern.
* The company assumes no responsibility when it was used outside Japan.
* As for SnomD735 regular server maintenance, you may experience temporarily service stops without prior notice.
* The company assumes no responsibility when the customers caused the phone primary source of malfunction or
breakdown.

3
Maintenance/Cleaning
Please use soft dry clothes to clean the device.
Don’t use wet clothes.
Don’t use volatile chemical like benzene, or thinner since they can damage the device.
If you want to use a chemical wipe, please read the cautionary notes before using it.
Connection Method:
1. Connect the handset cord in the handset and connect it on the main body.
2. Plug the LAN cable(network) into the RJ45 connector labeled “NET” and plug the other end into the network side
to establish a data link.
3. The second RJ45 connector, labeled “PC”, is for daisy-chaining further Ethernet devices without the need for a
second Ethernet connection line.
4. Insert the plug of the power supply into the connector labeled “DC 5V” and hooks up the casing into the mains.
5. If you want to use a headset, connect it to the RJ audio jack on the bottom shell of the phone.
Snom D735
Snom D735 is a phone device that can be used with our service. It cannot be used as a typical phone. The customer
must subscribe to an Internet Service Provider to be able to use the device. Customer with no broadband router
feature must provide a separate broadband router.

4
①
②③④
⑤
⑥
⑦
⑧
⑨
Keypad Familiarization
1. Navigation key - for navigation within the display menu and the phone book.
2. Enter key - to confirm actions, selections and inputs.
*Always press the “ENTER Key” after inputting the numbers dialed
3. Cancel Key - to cancel actions or inputs.
4. LED for MWI - (Message Waiting Indicator)
5. Mute Key - Mute/unmute microphone
Volume Key - key to adjust the volume to (lower/higher)
Speaker - turns the speaker on/off
Headset Key - Headset mode on/off
6. Freely programmable function keys - The 8 keys around the display with LEDs are the programmable function keys
onto which different functionalities can be mapped.
7. Function keys F1–F4 - Standard functions available on idle screen.
8. Directory Key - Internal phone directory
Setting Key - Setting menu
Transfer Key - Transfer call
Hold Key - Key to Put call on hold/resume call
9. DND Key - Turn "do not disturb" (DND) mode on and off for all identities registered on the phone.

5
General Settings
1. Verify device’s IP Address. Press [Setting Key] Select [Information], then [System Info]. IP Address will appear.
2. Snom D735 and the PC must be connected to the same network. Launch any web browser such as Internet
Explorer. Enter IP Address observing the format below.
http: // (IP address)
*After initializing the device that you access, you will still not be prompted to enter a username/password.
In order to prevent unauthorized login, please set username and password
If you are unsure of the password please contact our customer service representative.

6
Display Name and Account: Enter [Unique ID].
Password: Enter [Registered Password] .
Registrar and Outbound Proxy: Enter [Login Server] and [:25060] after login server.
Authentication Username: Enter [Unique ID].
Mailbox: Enter [999].
Display text for idle screen: Enter [Extension Number].
* Click [Apply] to save changes.
*Click [Ringtone] to change your ringing tone. You can listen through your device when you click [Play Ringer],
and make sure to check the device’s volume.
3. On the [Setup] options, select [Identity 1].
ユニーク
ユニーク
パスワード
ユニーク
ログインサーバ:25060
ログインサーバ:25060
Unique
Unique
Password
Login server：25060
Login server：25060
Unique
999
Extension Number

7
Keepalive Interval (seconds): Enter [20] seconds.
*Click [Save] to save changes.
5. On the [Setup] options, select [Identity 1], then click [NAT].
4. On the [Setup] options, select [Identity 1], then click [SIP].
When you are in a call, another call coming in will be announced visually by the flashing call LED and by the
symbol appearing in the function key line (Fig. 1); it will also be announced acoustically by a double beep. You
can also change the setting If you want to switch to visual or acoustic announcement only or turn call waiting off
completely.
*Click [Save] to save changes.
20

8
*
5. On the [Setup] options, select [Identity 1], then click [RTP].
Codec : Enter [pcmu,telephone-event].
* If you use our call center system, CTI, please select “off” for RTP Encryption
*Click [Save] to save changes.
Web Interface Language: Select [English].
Language: Select [English].
*Click [Save] to save changes
6. On the [Setup] options, select [Preferences].

9
7. On the [Setup] options, select [Preferences], then click [Appearance].
Number Display Style: Select [Number].
*Click [Save] to save changes
8. On the [Setup] options, select [Preferences], then click [Audio].
Tone Scheme: Select [Japan].
*Click [Save] to save changes

10
TRANSFER Type: Select [DTMF]
TRANSFER Number: Enter [#9]
*Click [Save] to save changes
9. On the [Setup] options, select [Function Keys]
Setting Key Allocations

11
NTP Time Server: Enter [ntp.jst.mfeed.ad.jp].
Timezone: Select preferred time zone
* Click [Save] to save changes.
10. On the [Setup] options, select [Advanced]
ntp.jst.mfeed.ad.jp

12
Network identity(port): Enter any number between 50000 and 60000.
Please don’t enter the same number to the other devices.
Time Support (RFC4028): Select [OFF].
* Click [Save] to save changes
11. On the [Setup] options, select [Advanced], then click [SIP/RIP]
50000〜60000

13
Filter Packets from Registrar：Select [off]
12. On the [Setup] options, select [Advanced], then click [QoS/Security]
Set password for “Administrator Password”
Set User and Password for “HTTP Server”
* Click [Save] to save changes

14
13. On the [Setup] options, select [Advanced], then click [Update].
Update Policy: Select [Never update, do not load settings].
PnP Config: Select [ON].
* Click [Apply] to save changes.
*Click [Reboot] to reboot the device to apply all changes.
Please refer to “Snom D735 wiki” if you want to see more about Snom D735
http://wiki.snom.com/D735

15
14. Confirm device registration on customer management page.
(1) Go to [Unique List]
(2) Search the unique to which the device was assigned.
This icon indicates that the settings were loaded successfully; device is registered and can
now be used.
This is shown if the device was not able register due to provisioning or other unexpected
error. Please see the troubleshooting section. If it still fails after several attempts, please
contact us.

16
Verify from Settings Screen
Dialed Numbers: List of previously called/dialed numbers.
Missed Calls: List of calls that is terminated before being answered by its intended recipient.
Received Calls: List of calls answered by the call recipient.
* Calls can be made with just a click from the numbers on the list.
Verify from the device.
Dialed Numbers: “↑” or “↓” of Navigation Key
Missed Calls: “→” of Navigation Key
Received Calls: “←” of Navigation Key
Or, you can see the history on the display menu “Call History”.
VIEWING OF CALL HISTORY
On the [Operation] options, select [Home].
You can view the call history on the figure below.

17
Set blocked numbers in the [Add or Edit Entry] area.
Example:
Number: Type the number @XXX.XXX.XXX.XXXX (Server IP address).
Number Type: Select [sip].
Contact Type: Select [Deny List].
Outgoing Identity: [Active]
Then, click [Add/Edit]. Configured number will be displayed. If you wish to delete a number, click [Delete].
*The Server IP address depends on your account.
You can also reject calls from anonymous callers.
The number must be registered in the device to be set as an anonymous caller.
Example:
Number: Anonymous @XXX.XXX.XXX.XXXX (Server IP address)
SETTING BLOCKED NUMBERS
On the [Operation] options, select [Directory].

18
Dial-Plan String: Enter [^(0[0-9]*)$|sip:184\1@\d;phone=yes| ]
* You can set up the dial plan for this line here. With a dial plan, you can match user input (digits via
keyboard) to specific actions like dialing, using a distinct outgoing identity, etc.
* Use our service phone’s extension number for transfers.
* Click [Save] to save changes.
SETTING PREFIX (184)
*You can make an anonymous call if you put the prefix 184 in Japan.
On the [Operation] options, select [Directory], then click [SIP].

19
Save back up data of phone settings
On the [Status] options, select [Settings].
Click “here” of Click here to save the settings.
The setting file be displayed in a new tab on the browser.
Ex.: http:// IP Address /settings.cfg
Please copy the setting and paste it to Memo (Notepad), and save the file.
*This setting is not including Unique ID, password and the other SIP information.

20
Upload back up data of phone settings
On the [Setup] options, select [Advanced], then click [Update].
Select back up data file and click “Load” on Update Setting File manually