SOMFY Roll Up 28 WireFree RTS User manual

Instructions
Instrucciones
Notice
EN
ES
FR
Roll Up 28
WireFree RTS

2
Copyright © 2017 - 2018 SOMFY ACTIVITES SA, Société Anonyme. All rights reserved
EN Roll Up 28 WireFree RTS
1. PRIOR INFORMATION
1. 1. SPHERE OF APPLICATION
Roll Up 28 drives are designed to drive most types of interior roller and roman blinds.
The installer, a home motorisation or home automation professional, must ensure that once the driven product
is installed, it respects the current standards in the country of installation, notably standard EN 13120 relative to
interior blinds.
1. 2. LIABILITY
Before installing and using the drive, please read these instructions carefully. In addition to the instructions provided
in this guide, please also comply with the instructions set out in the enclosed Safety instructions document.
The drive must be installed by a home motorisation and automation professional, in accordance with Somfy’s
instructions and the applicable regulations in the country of installation.
Any operation of the drive outside the sphere of application described above is prohibited. Such operation
shall exclude Somfy from all liability and invalidate the Somfy warranty, as will any failure to comply with the
instructions given herein and in the enclosed Safety instructions document.
Aer installing the drive, the installer must inform his customers of the operating and maintenance conditions
for the drive and must pass the operating and maintenance instructions on to them, as well as the enclosed
Safety instructions document. Any Aer-Sales Service operation on the drive requires intervention by a home
motorisation and automation professional.
Should any doubt arise during installation of the drive or for additional information, consult a Somfy contact or
visit www.somfy.com.
⚠Safety Warning ! 1
Warning ! Β Information
ORIGINAL INSTRUCTIONS
CONTENTS
1. Prior information 2
1. 1. Sphere of application 2
1. 2. Liability 2
2. Installation 3
2. 1. Assembly 3
2. 2. Wiring 4
2. 3. Commissioning 4
2. 4. Tips and advice on installation 6
3. Operation and maintenance 9
3. 1. Mode selection: Roller or Tilting mode 9
3. 2. Controlling Up, Down, My: In roller mode 9
3. 3. Controlling Up, Down, My: In Tilting mode 9
3. 4. Adjusting the tilting speed 10
3. 5. Favorite (my) position 10
3. 6. Adjusting the speed 11
3. 7. Tips and advice on operation 11
4. Technical data 12
These instructions apply to all Roll Up 28 drive, the different versions of which are available in the current catalogue.

3
Copyright © 2017 - 2018 SOMFY ACTIVITES SA, Société Anonyme. All rights reserved
EN
Roll Up 28 WireFree RTS
2. INSTALLATION
1
These instructions are mandatory for the home motorisation and automation professional installing
the drive.
1
Never drop, knock or puncture the drive or immerse it in liquid.
1
Install an individual control point for each drive.
2. 1. ASSEMBLY
2. 1. 1. Drive preparation
1) Fit the crown (a) and drive wheel (b) to the
motor.
2) Measure the length (L) between the end of the
drive wheel and the head end.
2. 1. 2. Tube preparation
Cut the tube to the required length.
Deburr the tube and remove the debris.
2. 1. 3. Drive/tube assembly
1) Slide the drive into the tube. Insert the wheel
by aligning the wheel to the tube profile. Insert
the drive half way and then slide the crown
down the drive and insert it in the tube. Finally,
push the motor inside the tube.
2) Not required, but if needed, fix the tube to the
drive with self-tapping screws or steel pop
rivets depending on the dimension (L).
2. 1. 4. Mounting the tube-drive assembly on the brackets
a) Standard bracket
b) Drive plate for specific bracket
⚠For optimal radio reception, the motor
antenna should be kept straight and should
be positioned outside of headrail (if used).
L
1
2
a b
L
1
2
a b

4
Copyright © 2017 - 2018 SOMFY ACTIVITES SA, Société Anonyme. All rights reserved
EN Roll Up 28 WireFree RTS
2. 2. WIRING
⚠To ensure electrical safety, this Class III motor must
be powered by a «SELV» voltage source (Safety
Extra Low Voltage).
Plug the battery with the motor supply cable.
⚠Warning: Do not unplug the battery when the motor
works.
2. 3. COMMISSIONING
2. 3. 1. Wake up the drive
For initial unpacking of drive, wake up the drive by briefly
pressing the motor head programming button or plugging
in the charger.
The driven product briefly moves Up and Down 3 times.
1
To avoid accidental programming of drive(s) once awake, follow section “Activate/Deactivate “RTS” radio
technology when control point is temporarily preprogrammed (not paired) to the driven product” to deactivate
RTS.
Β The drive will go back to sleep if le untouched for 15 minutes.
2. 3. 2. Preprogramming the control point
Press the UP and DOWN buttons simultaneously on the control point:
the driven product moves Up and Down and the control point is temporarily programmed to driven product.
2. 3. 3. Checking the rotation direction
Press the control point UP button:
a) If the driven product raises (a), the rotation direction
is correct: proceed to section “Setting the end limits”.
b) If the driven product is lowers (b), the rotation
direction is incorrect: move to the next step.
• b1) Press the control point MY button until the
driven product moves Up and Down: the rotation
direction has been modified.
• b2) Press the control point UP button to confirm the
rotation direction.
3x
a
b
=
=
b2b1

5
Copyright © 2017 - 2018 SOMFY ACTIVITES SA, Société Anonyme. All rights reserved
EN
Roll Up 28 WireFree RTS
2. 3. 4. Setting the end limits
Β The end limits can be set in any order.
1) Press and hold the UP button to move the driven
product to the desired Up position. If necessary,
adjust the Up position using the UP or DOWN buttons.
2) To memorize the UP limit: Press the
MY and DOWN buttons simultaneously and
release once the driven product begins to move.
The Up limit is now memorized.
3) Press the MY button when the driven product
reaches the desired Down position. If necessary,
adjust the down position using the UP or DOWN
buttons.
4) To memorize the Down limit: Press the MY
and UP buttons simultaneously and release when
the driven product begins to move. The Down limit
is now memorized. The driven product moves up and
will stop at its upper limit.
5) To confirm and complete limit programming: Press and hold the MY button until the driven product
briefly moves Up and Down. The end limits are now recorded.
2. 3. 5. Activate/Deactivate “RTS” radio technology when control point is temporarily preprogrammed
(not paired) to the driven product.
Β This function is used to deactivate the radio transmission to save the battery life during shipment, or when the
product will not be used for an extended amount of time (ex: storage).
1) To deactivate the “RTS” Radio Technology Somfy,
press the UP, MY and DOWN buttons simultaneously,
until the driven product briefly moves Up and Down
once.
2) To activate the “RTS” Radio Technology Somfy,
briefly press the motor head programming button,
the driven product briefly moves Up and Down three
times.
2. 3. 6. Recording “Pairing” the control point
Aer recording the end limits:
Briefly press the control point programming button. The
driven product will
briefly move Up and Down to confirm
pairing.
The control point is recorded “paired” to driven
product.
1 2
3 4
5
1 2
3x
PROG.

6
Copyright © 2017 - 2018 SOMFY ACTIVITES SA, Société Anonyme. All rights reserved
EN Roll Up 28 WireFree RTS
2. 4. TIPS AND ADVICE ON INSTALLATION
2. 4. 1. Questions about the drive?
Observations Possible causes Solutions
The driven product does
not operate.
Drive battery is low and requires
charge.
Charge the battery.
The control point battery is low. Check the battery and replace it as
required.
The control point is not compatible
or not programmed.
Check the compatibility and replace the
control point as required.
The thermal protection has
activated.
Wait for the drive to cool down.
The driven product stops
too soon.
The end limits are incorrectly
programmed.
Reset the end limits.
The driven product has exceeded
recommended weight limit.
Replace driven product.
Battery is low. Charge the battery.
Red LED blinks slowly for
3 seconds before and aer
motor running.
Battery is low. Battery capacity is
less than or equal to 5%.
Charge the battery.
2. 4. 2. End limit readjustment
1
Control point must be paired to the driven product.
Β Green LED lights on for Up limit adjusting and blinks slowly for Down limit adjusting.
Readjusting the upper end limit
1) Briefly press the UP button, to move the driven
product to the upper end limit.
2) Press and hold the UP and DOWN buttons
simultaneously until the driven product briefly
moves Up and Down.
3) Press and hold the UP or DOWN button to move the
driven product to the new desired position.
4) To confirm the new position press and hold the MY
button until the driven product briefly moves Up and
Down.
1 2
34

7
Copyright © 2017 - 2018 SOMFY ACTIVITES SA, Société Anonyme. All rights reserved
EN
Roll Up 28 WireFree RTS
Readjusting the lower end limit
1) Briefly press the DOWN button to move the driven
product to the lower end limit.
2) Press and hold the UP and DOWN buttons
simultaneously until the driven product briefly moves
Up and Down.
3) Press and hold the UP or DOWN button to move the
driven product to the new desired position.
4) To confirm the new position press and hold the MY
button until the driven product moves Up and Down.
2. 4. 3. Modifying the motor rotation direction
1) Using the UP or DOWN button on the control point,
move the driven product away from the end limits.
2) Press and hold the UP and DOWN buttons
simultaneously until the driven product briefly moves
Up and Down.
3) Press the MY button until the driven product briefly
moves Up and Down to reverse the rotation direction.
4) Press the UP button to check the new rotation
direction. The motor rotation direction is reversed.
2. 4. 4. Modifying the wheel rotation direction
1) Using the UP or DOWN button on the control point,
move the driven product away from the end limits.
2) Press and hold the UP and DOWN buttons
simultaneously until the driven product briefly moves
Up and Down.
3) Press the UP, MY and DOWN buttons simultaneously,
until the driven product briefly moves Up and Down,
wheel rotation is reversed.
1 2
34
1 2
34
1
2 3

8
Copyright © 2017 - 2018 SOMFY ACTIVITES SA, Société Anonyme. All rights reserved
EN Roll Up 28 WireFree RTS
2. 4. 5. Erasing control points (transmitters) from memory
To delete all the programmed transmitters, press and
hold the motor head programming button until the driven
product briefly moves Up and Down twice. All
programmed control points (transmitters) are deleted.
2. 4. 6. Erasing the memory of the motor (factory default)
To reset the motor, press and hold the motor head
programming button until the driven product briefly
moves Up and Down 3 times.
All the settings are erased.
2. 4. 7. Sleeping mode
1
The driven product must be programmed.
Β This feature temporarily prevents the drive product from responding to any previously programmed control
points (transmitter) commands.
1) Press and hold the motor head programming button
until the driven product
briefly moves Up and Down.
2) Briefly press the motor head programming button,
the driven product
briefly moves Up and Down
twice. “Sleeping mode” is activated.
3) To deactivate the “Sleeping mode”, briefly press the
motor head programming button. The driven product
briefly moves Up and Down, the control point
(transmitter) commands are enabled.
2x
3x
2
3
1
2x

9
Copyright © 2017 - 2018 SOMFY ACTIVITES SA, Société Anonyme. All rights reserved
EN
Roll Up 28 WireFree RTS
3. OPERATION AND MAINTENANCE
3. 1. MODE SELECTION: ROLLER OR TILTING MODE
The Roll Up 28 is designed to work in 2 modes: Tilting mode or Roller mode.
This feature allows the Roll Up 28 to be set according to the type of application.
Β The Roll Up 28 is set (by default) to work in Roller mode.
Β Yellow LED lights on in Roller mode.
1) Move the driven product away from the end limits.
2) Simultaneously press and hold the UP and DOWN
buttons until the driven product briefly moves Up
and Down.
3) Press and hold the MY and DOWN buttons
simultaneously until the driven product
briefly
moves Up and Down to change from Roller mode to
Tilting mode.
Β Yellow LED blinks slowly in Tilting mode.
3. 2. CONTROLLING UP, DOWN, MY: IN
ROLLER MODE
1) To move the driven product from a limit to the
other limit, briefly press the UP or DOWN button.
2) To stop the driven product, briefly press the MY
button.
3) (If a my position is recorded) To move the driven
product to the my position, briefly press the MY
button.
3. 3. CONTROLLING UP, DOWN, MY: IN
TILTING MODE
1) To move the driven product from a limit to the other
limit, briefly press (less than 0,5s) the UP or DOWN
button.
2) To stop the driven product, press the MY button.
3) (If a my position is recorded) To move the driven
product to the my position, briefly press the MY
button. The driven product will automatically travel
to the down end limit (first) then to the my position.
4) To tilt the slats, press and hold the UP or DOWN
button or use the scroll of the remote control, until
the slats reach the desired position.
1
23
1
2 3
1
2 3
4

10
Copyright © 2017 - 2018 SOMFY ACTIVITES SA, Société Anonyme. All rights reserved
EN Roll Up 28 WireFree RTS
3. 4. ADJUSTING THE TILTING SPEED
1) To decrease the tilting speed, press and hold the
MY and DOWN buttons simultaneously until the
driven product briefly moves Up and Down. Repeat
as needed. The minimum speed has been reached
when the driven product no longer moves Up and
Down.
2) To increase the tilting speed, press and hold the
MY and UP buttons simultaneously until the driven
product briefly moves Up and Down. Repeat as
needed. The maximum speed has been reached
when the driven product no longer moves Up and
Down.
3. 5. FAVORITE my POSITION
Β A intermediate stop or “favorite (my) position,” which is commonly used between the fully Up and Down
positions.
1) To set this function, move the driven product to
the desired position using the UP or DOWN button.
Briefly press MY button to stop the driven product.
2) Press and hold the MY button until the driven product
moves Up and Down. Favorite (my) position is set.
3. 5. 1. To modify the favorite (my) position
1) Use the UP or Down button to move the driven
product to the NEW desired favorite (my) position.
2) Press the My button to stop the driven product.
3) Press and hold the MY button until the driven product
briefly moves Up and Down. The new favorite (my)
position is programmed.
Β Only one favorite (my) position is permitted.
3. 5. 2. To use the favorite (my) position
1
The driven product must be stopped.
-Briefly press the MY button: the driven product moves
to the favorite (my) position.
1
2
1 2
1 2