Sony HSCU300RF User manual

HSCU300RF/HSCU300R (GB) 4-479-632-11 (1)
4-479-632-11 (1)
English
Before operating the unit, please read this manual thoroughly and retain it for
future reference.
WARNING
To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
THIS APPARATUS MUST BE EARTHED.
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING: THIS WARNING IS APPLICABLE FOR USA ONLY.
If used in USA, use the UL LISTED power cord specified below.
DO NOT USE ANY OTHER POWER CORD.
Plug Cap Parallel blade with ground pin (NEMA 5-15P Configuration)
Cord Type SJT, three 16 or 18 AWG wires
Length Minimum 1.5 m (4 ft 11 in), Less than 2.5 m (8 ft 3 in)
Rating Minimum 10A, 125V
Using this unit at a voltage other than 120V may require the use of a different
line cord or attachment plug, or both. To reduce the risk of fire or electric shock,
refer servicing to qualified service personnel.
WARNING: THIS WARNING IS APPLICABLE FOR OTHER COUNTRIES.
1. Use the approved Power Cord (3-core mains lead) / Appliance Connector /
Plug with earthing-contacts that conforms to the safety regulations of each
country if applicable.
2. Use the Power Cord (3-core mains lead) / Appliance Connector / Plug
conforming to the proper ratings (Voltage, Ampere).
If you have questions on the use of the above Power Cord / Appliance Connector
/ Plug, please consult a qualified service personnel.
For kundene i Norge
Dette utstyret kan kobles til et IT-strømfordelingssystem.
(HSCU300RF only)
Caution
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
This HD Camera Control Unit is classified as a CLASS 1 LASER PRODUCT.
Tämä HD-kameraohjausyksikkö on luokiteltu 1. LUOKAN LASERTUOTTEEKSI.
Den här kontrollenheten för HD-kamera klassificeras som en LASERPRODUKT
AV KLASS 1.
Caution
The use of optical instruments with this product will increase eye hazard.
For the customers in the U.S.A.
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.
You are cautioned that any changes or modifications not expressly approved in
this manual could void your authority to operate this equipment.
All interface cables used to connect peripherals must be shielded in order to
comply with the limits for a digital device pursuant to Subpart B of part 15 of FCC
Rules.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
For the customers in Canada
CAN ICES-3 (A)/NMB-3(A)
For the customers in Europe
This product with the CE marking complies with the EMC Directive issued by the
Commission of the European Community.
Compliance with this directive implies conformity to the following European
standards:
EN55103-1: Electromagnetic Interference (Emission)

EN55103-2: Electromagnetic Susceptibility (Immunity)

This product is intended for use in the following Electromagnetic Environment:
E4 (controlled EMC environment, ex. TV studio).
For the customers in Europe, Australia and New Zealand
WARNING
This is a Class A product. In a domestic environment, this product may cause
radio interference in which case the user may be required to take adequate
measures.
For the customers in Europe
This product has been manufactured by or on behalf of Sony Corporation,
1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan. Inquiries related to product
compliance based on European Union legislation shall be addressed to the
authorized representative, Sony Deutschland GmbH, Hedelfinger Strasse 61,
70327 Stuttgart, Germany. For any service or guarantee matters, please refer to
the addresses provided in the separate service or guarantee documents.
This apparatus shall not be used in the residential area.
For the State of California, USA only
Perchlorate Material - special handling may apply,
See www.dtsc.ca.gov/hazardouswaste/perchlorate
Perchlorate Material : Lithium battery contains perchlorate.
For the customers in Taiwan only
For the customers in the U.S.A.
SONY LIMITED WARRANTY - Please visit http://www.sony.com/psa/warranty
for important information and complete terms and conditions of Sony’s limited
warranty applicable to this product.
For the customers in Canada
SONY LIMITED WARRANTY - Please visit http://www.sonybiz.ca/solutions/
Support.do for important information and complete terms and conditions of
Sony’s limited warranty applicable to this product.
For the customers in Europe
Sony Professional Solutions Europe - Standard Warranty and Exceptions on
Standard Warranty.
Please visit http://www.pro.sony.eu/warranty for important information and
complete terms and conditions.
For the customers in Korea
SONY LIMITED WARRANTY - Please visit http://bpeng.sony.co.kr/handler/
BPAS-Start for important information and complete terms and conditions of
Sony’s limited warranty applicable to this product.
Overview
The HSCU300RF Camera Control Unit connects to a Sony HSC300RF or

HSC100RF HD color camera via an optical fiber cable. It performs signal
processing, provides an interface for external equipment, and supplies power
to the camera.
The HSCU300R Camera Control Unit connects to a Sony HSC300R or HSC100R

HD color camera via a triaxial cable.
It performs signal processing, provides an interface for external equipment,
and supplies power to the camera.
Using the CD-ROM manual
The manual can be read on a computer with Adobe Reader installed.
You can download Adobe Reader free from the Adobe website.
1 Open the index.html file in the CD-ROM.
2 Select and click on the manual that you want to read.
Note
If you have lost or damaged the CD-ROM, you can purchase a new one from your
Sony dealer or Sony service counter.
HD Camera Control Unit
Operation Guide
© 2013 Sony Corporation Printed in Japan
HSCU300RF
HSCU300R

HSCU300RF/HSCU300R (GB) 4-479-632-11 (1)
Specifications
General
Power supply AC 100 to 240 V, 50/60 Hz
Current consumption 4.5 A (max)
Inrush current
(1) Maximum possible inrush current at initial switch-on (Voltage
changes caused by manual switching):
43 A peak, 5.5 A r.m.s. (240 V AC)
(2) Inrush current after a mains interruption of five seconds
(Voltage changes caused at zero-crossing):
2.9 A peak, 1.4 A r.m.s. (240 V AC)
Operating temperature 5 °C to 40 °C (41 °F to 104 °F)
Storage temperature –20 °C to +60 °C (–4 °F to +140 °F)
Weight Approx. 6.7 kg (14 lb 12 oz) (HSCU300RF),
Approx. 7.9 kg (17 lb 6.7 oz) (HSCU300R)
Input/output connectors
CAMERA HSCU300RF
Optical Fiber connector (1)
HSCU300R
Triax connector (1)
INTERCOM XLR 5-pin (1)
INTERCOM/TALLY/PGM D-sub 25-pin, female (1)
INCOM (PROD/ENG), 4W/RTS/CC, 0 dBu
TALLY (R, G)
PGM 2-system, –20 dBu/0 dBu/+4 dBu
REMOTE 8-pin multiconnector (1)
MIC/WF REMOTE/TRUNK D-sub 25-pin, female (1)
LAN 8-pin (1)
CAUTION
  For safety, do not connect the connector for
peripheral device wiring that might have
excessive voltage to this port.
When you connect the LAN connector
cable of the unit to peripheral device, use a
shielded-type cable to prevent malfunction
due to radiation noise.
Input connectors
AC IN (1), AC 100 to 240 V
SDI RETURN 1, 2 BNC type (2)
HD SDI: SMPTE 292M, 0.8 Vp-p, 75 Ω,
1.485/1.4835 Gbps bit rate
SD SDI: SMPTE 259M, 270 Mbps bit rate
VBS RETURN 1, 2 BNC type (2), 1.0 Vp-p, 75 Ω
REFERENCE IN/OUT BNC type (2), loop-through output
HD: SMPTE 274M, tri-level sync, 0.6 Vp-p, 75 Ω
SD: Black burst (NTSC: 0.286 Vp-p, 75 Ω/PAL: 0.3 Vp-p, 75 Ω)
PROMPTER 1, 2 BNC type (2), VBS signal, 1.0 Vp-p, 75 Ω 2 systems
Output connectors
SDI OUTPUT 1, 2 BNC type (2)
HD SDI: SMPTE 292M, 0.8 Vp-p, 75 Ω,
1.485/1.4835 Gbps bit rate
SD SDI: SMPTE 259M, 0.8 Vp-p, 75 Ω, 270 Mbps bit rate
HD SDI/SD SDI selectable
SDI OUTPUT 3, 4 (MONITOR)
BNC type (2)
HD SDI: SMPTE 292M, 0.8 Vp-p, 75 Ω,
1.485/1.4835 Gbps bit rate
SD SDI: SMPTE 259M, 0.8 Vp-p, 75 Ω, 270 Mbps bit rate
HD SDI/SD SDI selectable
Pr/R/R-Y, Y/G/Y, Pb/B/B-Y
BNC type (3)
HD component video
Y (100% white): 0.7 Vp-p
Pr/Pb (75% color bar): 0.7 Vp-p, 75 Ω
HD RGB video
R/G/B (100% white): 0.7 Vp-p, 75 Ω
SD RGB video
R/G/B (100% white): 0.7 Vp-p, 75 Ω
SD component video
Y (100% white): 0.714 Vp-p
Pr/Pb (75% color bar): 0.756 Vp-p, 75 Ω
VBS1, VBS2 BNC type (2), VBS 1.0 Vp-p, 75 Ω
PIX BNC type (1), VBS/R/G/B (VBS 1.0 Vp-p, 75 Ω)
SYNC/WF BNC type (1)
SYNC
HD: BTA-S001A, tri-level sync, 0.6 Vp-p, 75 Ω
SD: composite sync, 0.3 Vp-p, 75 Ω
HD SYNC/SD SYNC selectable
WF
VBS/R/G/B/SEQ (VBS 1.0 Vp-p, 75 Ω)
MIC OUT XLR 3-pin, male (2), 0 dBu / –20 dBu
Supplied accessories
Number plates (1 set)
Operation guide (1)
Operation manual (CD-ROM) (1)
Optional accessories
HKCU-FP2 CCU Control Panel
HZCU-MC3 Camera Operating Software
United States and Canada: Plug holder B (2-990-242-01)
Other areas: Plug holder C (3-613-640-01)
United States and Canada: Power cord set (1-551-812-XX)
Other areas: Power cord set (1-782-929-XX)
CCA-5-3 (3 m), CCA-5-10 (10 m) connection cables
Maintenance manual
(HSCU300RF only)
Connectors for optical/electric composite cables:
LEMO® PUW.3K.93C.TLCC96 (to the “CAMERA” connector on CCU)

LEMO® FUW.3K.93C.TLMC96 (to the “CCU” connector on CAMERA)

Caution on the optical/electric composite cable:
For connection between the camera control unit and a camera, be sure to use
an optical/electric signal composite cable with the connectors specified in this
manual in order to comply with the limit for EMC regulations.
Related equipment
HD color camera
HSC300RF, HSC300R, HSC-300
HSC100RF, HSC100R, HXC-100
RCP-1000-series Remote Control Panel
MSU-1000/1500 Master Setup Unit
VCS-700 Video Selector
CNU-700 Camera Command Network Unit
Dimensions
Design and specifications are subject to change without notice.
Notes
Always verify that the unit is operating properly before use. SONY WILL

NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED
TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF
PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER
DURING THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY,
OR FOR ANY OTHER REASON WHATSOEVER.
SONY WILL NOT BE LIABLE FOR CLAIMS OF ANY KIND MADE BY USERS OF

THIS UNIT OR MADE BY THIRD PARTIES.
SONY WILL NOT BE LIABLE FOR THE TERMINATION OR DISCONTINUATION

OF ANY SERVICES RELATED TO THIS UNIT THAT MAY RESULT DUE TO
CIRCUMSTANCES OF ANY KIND.
395 mm (15 5/8in)
66 mm
(2 5/8in)
424 mm (16 3/4in)
482 mm (19 in)