Soundoff Signal ENT1B3(y) User manual

To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product please visit our website at www.soundoffsignal.com and select the “Warranty & Returns”
link along the left column of our home page. If you have questions regarding this product please contact Technical Services, Monday - Friday, 8 am to 5 pm at 1.800.338.7337, press #4 to
skip the automated message. Questions or comments that do not require immediate attention may be emailed to [email protected].
1.800.338.7337. / www.soundoffsignal.com / Thank you for trusting us with your safety!
OPERATION:
For details on operation see page with ‘Flash
Patterns’ table.
INTERSECTOR MIRROR LIGHT
ENT1B3(y) FOR 6 LED VERSION
ENT2B3(y) FOR 9 LED VERSION
Please see separate sheet
for Technical Specifications
• Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances.
These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these
devices to ensure compliance.
• DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to your vehicle
Owner’s Manual for the location of any air bag deployment zones.
• DO NOT connect this device to a strobe power supply. This product is self-contained and does not
require an external power supply.
ENT(x)B(xy) 5.10
Important Information:
The INTERSECTOR Mirror Light is designed
to be mounted under the vehicles side
mirrors and provide a warning signal to the
front and sides.
INSTALLATION:
Loosely assemble Intersector Light, correct
wedge block and curve block (P=Passenger,
D=Driver’s side, Crown-Vic and Dodge
Charger only) and position assembly below
side rear view mirror as shown at left.
Carefully remove light from stack without
changing position of wedge block. Mark and
drill pilot holes for #6 sheet metal screw.
Drill 3/8” hole in mirror shell if wire is to
be routed internally. If wire will be routed
external of the mirror shell this step can be
ignored.
Dismount mirror from door.
The following is particular to the Ford Crown-
Vic but can be applied to other vehicles as
well:
After pilot holes for #6 sheet metal screws
are drilled, a 3/8” bit should be used to
drill hole in race way next to mirror power
race. A 3/8” hole should then be made
between the pilot holes and the angled
toward the race way as shown in Figures
2-6 (second page). It is important to avoid
drilling through the power cable as this will
damage the mirror.
Using #6 machine screw, washer and
square nut assemble light and appropriate
wedge block, curve block (if required)
and gasket. Route wire carefully through
3/8” hole and into door. Use appropriate
#6 sheet metal screws to attach light to
underside of mirror. DO NOT OVERTIGHTEN
SCREWS AS THIS MAY DAMAGE THE
MIRROR OR LIGHT. Mirror may now be
replaced on vehicle.
Attach supplied female connector and make
other appropriate wiring connections inside
of door.
WIRE HOOK-UP TABLE
WIRE COLOR:
(ALL WIRES 20ga)
CONNECT TO:
(FROM FLASHER ONLY)
RED +10-16Vdc
WHITE Pattern Select / Sync
BLACK Ground (-)
GREEN Cruise Mode (+10-
16Vdc)
!
WARNING
This product contains high intensity LED devices. To
prevent eye damage, DO NOT stare into the light
beam at close range.
Mirror Light
Shown with
optional cord
strain relief
Wedge Block
0°, 5° and 10°
Curve Block
(used on Crown-
Vic and Charger
only)
Foam Gasket
RED WHITE BLACK GREEN
DBCA
DBCA
RED
WHITE
BLACK
GREEN
FEMALE
CONNECTOR
MALE
CONNECTOR
FROM FLASHER
INTERSECTOR
LIGHT
ALL WIRES 22ga
IMPORTANT:
Power should only be
supplied through RED
WIRE of flasher harness
and must be fused with
a 3A, user supplied,
in-line fuse. Failure to
install this fuse will create
a fire hazard and will
damage the Intersector
Light. Connecting the
Intersector light to any
power source directly
WILL permanently
damage the light and will
void warranty.

INTERSECTOR MIRROR LIGHT
ENT1B3(y) FOR 6 LED VERSION
ENT2B3(y) FOR 9 LED VERSION
ENT(x)B(xy) 5.10
POWER HARNESS WITH IN-LINE FLASHER
INTERSECTOR LIGHT WITH CABLECONNECTOR
SQUARE NUT WASHER 3/8” MACHINE
SCREW
USE TO JOIN LIGHT TO WEDGE BLOCK AFTER
CORD EXIT IS DETERMINED
3/4” SHEET
METAL SCREW
1/2” SHEET
METAL SCREW
USE WHEN
CURVE BLOCK IS
USED
USE WHEN
CURVE BLOCK IS
NOT USED
WEDGE BLOCKS
GASKET CURVE BLOCKS
(CROWN-VIC OR CHARGER ONLY)
P=PASSENGER SIDE
D=DRIVER SIDE
UTILITY BLOCK
0° (PARALLEL) 10° FOR TAHOE
5° FOR C-V,
IMPALA AND
CHARGER
DEGREE DESIGNATION IS EMBOSSED IN PART
PASSENGER OR
DRIVER SIDE
DESIGNATION IS
EMBOSSED IN PART
6-32 MACHINE SCREW
WASHER
IF DESIRED CORD MAY BE
EXTERNAL OF THE MIRROR
BY USING THE STRAIN RELIEF
AND THREAD CUTTING
SCREWS SUPPLIED
SQUARE NUT (USE MASKING
TAPE TO HOLD IN PLACE)
GASKET IS ALWAYS
POSITIONED NEXT TO MIRROR
SHELL RED
BLACK
GREEN
WHITE
FROM FLASHER
FROM LIGHT
COLORS AND LETTERS ON
CONNECTORS MUST MATCH
DO NOT INSTALL CONNECTOR
UNTIL LIGHT IS INSTALLED ON
MIRROR AND WIRE IS RUN TO
FINAL TERMINATION POINT
USER SUPPLIED 3A FUSE ON RED WIRE
DO NOT CONNECT DIRECTLY TO POWER
IMPORTANT NOTE:
Intersector lights are designed to be used with a specific power
harness. If replacement parts are used it is the installer’s
responsibility to ensure that the 6 LED version light is used with
the 6 LED version harness and the 9 LED version light is used with
the 9 LED version harness.

INTERSECTOR MIRROR LIGHT
ENT1B3(y) FOR 6 LED VERSION
ENT2B3(y) FOR 9 LED VERSION
ENT(x)B(xy) 5.10
Light should be positioned so that raised lines on lens is aligned
with long axis of vehicle.
VEHICLE LONG
AXIS
Drilling of inner part is only required on Crown-Vic. Tahoe and
Impala mirrors have sufficient clearances for cable. Cable for
Charger must be bundled with power cable of vehicle.
12 3
45 6

INTERSECTOR MIRROR LIGHT
ENT1B3(y) FOR 6 LED VERSION
ENT2B3(y) FOR 9 LED VERSION
ENT(x)B(xy) 5.10
PATTERN RESET
1. Remove power.
2. Place WHITE (sync) wire to ground.
3. With sync wire grounded, re-power RED wire.
4. Maintain for one second (light will dim).
5. Remove power and ground (pattern 1 set).
SINGLE LIGHT HEAD SET UP AND PATTERN SELECTION
1. Disconnect WHITE wire from any connections if applicable.
2. Turn INTERSECTOR MIRROR LIGHT ON by applying power to RED
WIRE from flasher. IMPORTANT NOTE: Power harness with in-line
flasher (PNT(x)FLA) MUST be used between power and light. Any
other flasher WILL cause permanent damage and void warranty.
3. Momentarily touching and removing the WHITE wire to ground will
advance the INTERSECTOR MIRROR LIGHT to the next flash pattern.
Touching and removing the WHITE wire for more than a few seconds
will allow you to change the INTERSECTOR MIRROR LIGHT to the
previous pattern. See flash pattern table. Continuing to touch and
remove the WHITE wire to ground will allow you to scroll through the
pattern list. After pattern #30 is reached the list will start over again
at pattern #1.
SINGLE COLOR AND DUAL COLOR CONFIGURATIONS
Follow the ID selection steps and set the INTERSECTOR MIRROR
LIGHT to the
following ID:
ID #2 - Single Color ID #4 - Single Color
Single Color - Simultaneous Flash Patterns:
- Set light heads to same ID (#2 or #4).
Single Color - Alternating Flash Patterns:
- Set one light head to ID #2 and another to ID #4.
MULTIPLE LIGHT HEAD SET UP AND PATTERN SELECTION
1. Set ID#
a. Connections
i. RED: +10-16Vdc
ii. WHITE: +10-16Vdc (Note: you will need to disconnect after
power is applied)
iii. BLK: Ground
iv. GREEN: NO CONNECTION REQUIRED FOR ID SELECTION
b. Apply power to unit
c. Without disconnecting power from unit, disconnect WHITE wire
d. Momentarily connect WHITE to Ground to change ID #
i. Identify ID# by number of sequential flashes
ii. Possible ID#s: 2 or 4
e. Disconnect Power to exit ID mode
2. Set Pattern - Must be done individually to each light prior to
syncing
a. RED: +10-16Vdc
b. BLACK: Ground
c. While light is powered, tap WHITE wire to ground to advance to
the next pattern (SEE pattern table at right)
d. Disconnect Power
3. Sync Lights
a. Once desired pattern has been selected for all light heads
connect all white wires and insulate with electrical tape.
4. Connect Master Switch for Application.
TECHNICAL SPECIFICATIONS
Overall Dimensions: 1.88”H x 2.88”W x 2.93”D
Flash Patterns: 30 flash patterns
Input Voltage Range: 10 - 16 Vdc (fused)
Current Consumption: 1.5A (maximum)*
# of LEDs: 6/9 Generation 3 LEDs
Light Sync Technology: No
Operating Temperature: -40º to +65º C
* PATTERN DEPENDENT
Flash Patterns
Pattern Name 1 Light Alternating 2 Lights
Simultaneous
2 Lights
F.P.M.
(Flashes /
Minute)
1. Quint
xx x70
2. Warp x x x 350
3. Inter-Cycle Flash xx
4. Double Flash xx x70
5. Quad Flash xx x80
6. PowerPulse™ x x x 180
7. RoadRunner™ x x x 113
8. Q-Switch™ xx
9. RoadRunner™ Steady Burn x x 113
10. Quad Steady Burn xx 80
11. E-Ideal Single Flash x x x 200
12. E-Ideal Double Flash x x x 146
13. Quad2 Flash xx x67
14. Double2 Flash xx x95
15. PowerRunner xx x
16. LCR Quint xx x
17. Warp3 xx x
18. Ultra Warp x x x 545
19. Thunder & Lightning xx
20. Lite Speed xx x85
21. SuperSonic x x 170
22. LCR Lite Speed xx x
23. SuperSonic Ultra xx x
24. Tempo Shift xx x
25. Tempo Shift Warp xx x
26. SBE2 xx x67
27. C2 x x x 200
28. U2 x x x 176
29. Cyclone xx x
30. Chameleon2 xx x
PENT1BØ(y) MODULE ONLY / NO FLASHER (6 LED)
PNT1FLA: Replacement Flasher Only / No Module (6 LED)
PENT2BØ(y) MODULE ONLY / NO FLASHER (9 LED)
PNT2FLA: Replacement Flasher Only / No Module (9 LED)
PNT1WDG: Replacement Wedge Set
PNT1CRVØ1: Replacement Curve Set
Replacement Parts & Accessories: