Soundoff Signal UltraLite EL3D02A00(x) User manual

To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product please visit our website at www.soundoffsignal.com and select the “Warranty & Returns”
link along the left column of our home page. If you have questions regarding this product please contact Technical Services, Monday - Friday, 8 am to 5 pm at 1.800.338.7337, press #4 to
skip the automated message. Questions or comments that do not require immediate attention may be emailed to [email protected].
1.800.338.7337. / www.soundoffsignal.com / Thank you for trusting us with your safety!
OPERATION:
1. Connect black wire to ground.
2. Connect red wire to +12Vdc through
5A fuse.
3. Apply +12Vdc to white wire for less
than one second (momentary) to
move forward one pattern.
4. Apply +12Vdc to white wire for one
second (until the lights dim) to move
to the first pattern.
5. Apply +12Vdc to white wire for more
than two seconds (until the lights turn
off) to turn off the UltraLITE.
6. To turn the unit back on, apply +12Vdc
to the white wire momentarily.
!
WARNING
This product contains high intensity LED devices.
To prevent eye damage, DO NOT stare into the
light beam at close range.
Please see reverse for
Technical Specifications
• Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances.
These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these
devices to ensure compliance.
• DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to your vehicle
Owner’s Manual for the location of any air bag deployment zones.
• DO NOT connect this device to a strobe power supply. This product is self-contained and does not
require an external power supply.
EL3DØ2AØØ(x) 10.10
Important Information:
INSTALLATION:
Before starting the installation make
certain you have the correct bracket
for your application. A universal Deck/
Dash mount bracket is supplied. For
other mounting brackets, see product
literature or visit our website.
Install the UltraLITE by following the
assembly instructions provided with the
brackets and check for security.
Important: DO NOT over tighten
mounting screws or nuts. This could
cause permanent damage to the light or
bracket. Use appropriate hardware for
mounting.
Universal bracket shown is supplied
but mounting screws are customer
supplied.
2 MODULE BAR
EL3D02A00(x) - 12V
EL3D02A00(x)-24 - 10-30V
BLACK
RED
WHITE
2 MODULE UltraLITE
+12Vdc
5A FUSE
SUPPLIED BAR MOUNTING HARDWARE
UNIVERSAL BRACKET

#PUL3M16AMB Amber
#PUL3M16BLU Blue
#PUL3M16GRN Green
#PUL3M16RED Red
#PUL3M16WHT White
See website or catalog for complete list of optional vehicle
specific brackets.
Replacement Modules:
EL3DØ2AØØ(x) 10.10
TECHNICAL SPECIFICATIONS
Overall Dimensions: 6.9”L x 1.54”H x 1.7”D
Flash Patterns: 33 flash patterns
Input Voltage Range: 10 - 16 Vdc
Current Consumption: <1 amp*
# of LEDs: 6 Generation 3 LEDs
Operating Temperature: -40º to +65º C
*Pattern Dependent
Flash Patterns
Alternating Patterns
FPM
(Flashes per Minute)
1. Quint 70
2. Warp 350
3. Inter-Cycle Flash
4. Double Flash 70
5. Quad Flash 80
6. Power Pulse 180
7. RoadRunner 113
8. Q-Switch
9. RoadRunner Steady Burn 113
10. Quad Steady Burn 80
11. E-Ideal Single Flash 200
12. E-Ideal Double Flash 146
13. Quad2 Flash 67
14. Double2 Flash 95
15. X-Warp
16. X-Double
17. PowerRunner
18. LCR Quint
19. Warp3
20. UltraWarp 545
21. Thunder and Lightning
22. LiteSpeed 85
23. SuperSonic 170
24. LCR LiteSpeed
25. SuperSonic Ultra
26. TempoShift
27. TempoShift Warp
28. SBE2 67
29. C2200
30. U2176
31. UltraGlow
32. Cyclone
33. Chameleon
2 MODULE BAR
EL3D02A00(x) - 12V
EL3D02A00(x)-24 - 10-30V