Soundoff Signal PINNACLE Mini Lightbar User manual

To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product please visit our website at www.soundoffsignal.com and select the “Warranty & Returns”
link along the left column of our home page. If you have questions regarding this product please contact Technical Services, Monday - Friday, 8 am to 5 pm at 1.800.338.7337, press #4 to
skip the automated message. Questions or comments that do not require immediate attention may be emailed to [email protected].
1.800.338.7337. / www.soundoffsignal.com / Thank you for trusting us with your safety!
OPERATION:
Electrical Connections
& Flash Pattern Selection:
See diagram at left for Power ON ( ),
Power OFF ( ) and Pattern SELECT
( ) switch positions. Turn the light
on by pressing the Power ON button. To
change the flash pattern press and hold
the PATTERN SELECT button for one
to two (1-2) seconds. The PINNACLE
Mini Lightbar will advance one (1) flash
pattern and flash the new pattern each
time this is done. The PINNACLE Mini
Lightbar features non-volatile memory
and will recall last pattern used.
Selected pattern will remain the default
once turned off and can be changed
by changing the flash pattern before
powering off.
!
WARNING
This product contains high intensity LED devices.
To prevent eye damage, DO NOT stare into the
light beam at close range.
Please see reverse for
Technical Specifications
• Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances.
These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these
devices to ensure compliance.
• DO NOT connect this device to a strobe power supply. This product is self-contained and does not
require an external power supply.
EPL7M+(x)C 6.09
Important Information:
INSTALLATION:
1) Detemine a clean, flat location
(typically the roof) on the vehicle to
mount the PINNACLE Mini Lightbar.
The PINNACLE Mini Lightbar comes
equipped with four magnetic
feet. It is the responsibility of the
installer and end user to determine
whether it is safe to use magnetic
mounting hardware for your
application. A Permanent Mount
version (EPL7PD(x)C) is available.
Note: The magnetic character of roof
steel varies from vehicle to vehicle.
Be sure that your vehicle is capable
of providing enough magnetic force
to safely secure the PINNACLE Mini
Lightbar to the roof.
2) A Protective Film has been provided
with the PINNACLE Mini Lightbar kit
thatcanbeappliedtothebottomofeach
magnet. This film will protect the paint
of the vehicle. Apply one donut shaped
decal to the bottom of each
magnetic foot. Be sure to cover
the magnet entirely for maximum
protection to the paint finish.
Note: Protective film can reduce the
magnetic force by as much as 10%.
EPL7000 PINNACLE MINI
LIGHTBAR MAGNET MOUNT
EPL7M+(x)C
Power ON
Power OFF
Pattern SELECT

PMB3BMG: Replacement Magnetic Foot (each)
PMB3MGKT: Replacement Magnetic Mount (kit)
PMB3TDC: Replacement Clear Dome
Replacement Parts & Accessories:
EPL7M+(x)C 6.09
EPL7000 PINNACLE MINI
LIGHTBAR MAGNET MOUNT
EPL7M+(x)C
TECHNICAL SPECIFICATIONS
Overall Dimensions: 14.25”L x 8.27”W x 2.93”H
Flash Patterns: 28 flash patterns
Input Voltage Range: 10 - 16 Vdc
Current Consumption: 2 Amps (Avg) - 4 Amps (Max)
# of LEDs: 24 Generation 3 LEDs
Operating Temperature: -40º to +65º C
Flash Patterns
Alternating Patterns
FPM
(Flashes per Minute)
1. Warp Alternating
2. Quad “
3. Quad2 “
4. Quint “
5. Double2 “
6. Warp 1, 2, 3 “
7. Progressive “
8. Q-Switch “
9. Intercycle “
10. Warp Whole Bar
11. Quad “
12. Quad2 “
13. Quint “
14. Double2 “
15. Warp 1, 2, 3 “
16. Progressive “
17. Warp Diagonal
18. Quad “
19. Quad2 “
20. Quint “
21. Double2 “
22. Warp 1, 2, 3 “
23. Progressive “
24. Q-Switch “
25. Intercycle “
26. Rotator “
27. Cycle 1 Random
28. Cycle 2 “