Soundoff Signal Intersector ENT3 3 Series User manual

INTERSECTOR™ LED LIGHT
#ENT3(y)3(x) - SURFACE MOUNT
#PNT3DGBB DECK/ GRILLE BRACKET, BLACK
OPERATION:
For details on operation see page with ‘Flash
Patterns’ table on last page.
Please see last page for
Technical Specifications
• Warning devices are strictly regulated and governed by Federal, State and Municipal ordinances.
These devices shall be used ONLY on approved vehicles. It is the sole responsibility of the user of these
devices to ensure compliance.
• DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to your vehicle
Owner’s Manual for the location of any air bag deployment zones.
• DO NOT connect this device to a strobe power supply. This product is self-contained and does not
require an external power supply.
Important Information:
WIRE HOOK-UP TABLE
WIRE COLOR:
(ALL WIRES 20ga)
CONNECT TO:
(FROM FLASHER ONLY)
RED +10-16 Vdc
WHITE Pattern Select / Sync
BLACK Ground (-)
GREEN Cruise Mode
(+10-16 Vdc)
!
WARNING
This product contains high intensity LED devices. To
prevent eye damage, DO NOT stare into the light
beam at close range.
IMPORTANT:
Power should only be
supplied through RED
WIRE of asher harness
and must be fused with
a 3A, user supplied,
in-line fuse. Failure to
install this fuse will create
a re hazard and will
damage the Intersector™
Light. Connecting the
Intersector™ light to any
power source directly
WILL permanently
damage the light and will
void warranty.
IMPORTANT! FOR
PROPER OPERATION
ALL WIRES MUST BE
CONNECTED FROM
FLASHER TO LIGHT
HEAD.
GREEN BLACK RED WHITE
1324
1324
GREEN
BLACK
RED
WHITE
FEMALE
CONNECTOR
MALE
CONNECTOR
FROM FLASHER
INTERSECTOR
LIGHT
ALL WIRES 22ga
SURFACE MOUNT
INSTALLATION:
1. Establish a position on the vehicle on a level
surface. Orient the light output level on the
horizon.
2. Use the gasket provided as a template to
mark locations of wire and mounting
screws
3. Use a 5/8” diameter drill for the wire holes
4. Size pilot holes for mounting screws
appropiately.
5. Fasten light using bezel and mounting
screws. Do not torque mounting screws
beyond 20 in - lbs.
DECK/ GRILLE BRACKET
INSTALLATION:
(PURCHASED SEPARATELY)
1. Slide wire from Bezel through center
access hole in the gasket and bracket.
2. Next, position the Housing over the Bezel
and align the holes with the bracket.
3. Lastly, using the supplied 8-32 x 1”
screws fasten the assembly lightly. Do
not torque mounting screws beyond 20
in - lbs.
4. Establish a position on the vehicle on a level
surface. Orient the light output level on the
horizon.
5. Use the bracket provided as a template to
mark locations of mounting screws.
6. Size pilot holes for mounting screws
appropiately.
7. Fasten light using bezel and mounting
screws. Do not torque mounting screws
beyond 20 in - lbs.
SURFACE MOUNT
DECK/ GRILLE BRACKET MOUNT
BRACKET
GASKET
BEZEL
HOUSING
8/32 x 1” PHIL PAN SCREWS

INTERSECTOR™ LED LIGHT
#ENT3(y)3(x) - SURFACE MOUNT
#PNT3DGBB DECK/ GRILLE BRACKET, BLACK
PATTERN RESET
1. Remove power.
2. Place WHITE (sync) wire to ground.
3. With sync wire grounded, re-power RED wire.
4. Maintain for one second (light will dim).
5. Remove power and ground (pattern 1 set).
SINGLE LIGHT HEAD SET UP AND PATTERN SELECTION
1. Disconnect WHITE wire from any connections if applicable.
2. Turn Intersector™ LED LIGHT ON by applying power to RED WIRE
from asher. IMPORTANT NOTE: Power harness with in-line asher
(PNT(x)FLA) MUST be used between power and light. Any other
flasher WILL cause permanent damage and void warranty.
3. Momentarily touching and removing the WHITE wire to ground
will advance the Intersector™ LED LIGHT to the next ash pattern.
Touching and removing the WHITE wire for more than a few seconds
will allow you to change the Intersector™ LED LIGHT to the previous
pattern. See ash pattern table. Continuing to touch and remove the
WHITE wire to ground will allow you to scroll through the pattern list.
After pattern #30 is reached the list will start over again at pattern
#1.
SINGLE COLOR CONFIGURATIONS
Follow the ID selection steps and set the Intersector™ LED LIGHT to
the following ID:
ID #2 - Single Color ID #4 - Single Color
Single Color - Simultaneous Flash Patterns:
- Set light heads to same ID (#2 or #4).
Single Color - Alternating Flash Patterns:
- Set one light head to ID #2 and another to ID #4.
MULTIPLE LIGHT HEAD SET UP AND PATTERN SELECTION
1. Set ID#
a. Connections
i. RED: +10-16Vdc
ii. WHITE: +10-16Vdc (Note: you will need to disconnect after
power is applied)
iii. BLK: Ground
iv. GREEN: NO CONNECTION REQUIRED FOR ID SELECTION
b. Apply power to unit
c. Without disconnecting power from unit, disconnect WHITE wire
d. Momentarily connect WHITE to Ground to change ID #
i. Identify ID# by number of sequential ashes
ii. Possible ID#s: 2 or 4
e. Disconnect Power to exit ID mode
2. Set Pattern - Must be done individually to each light prior to
syncing
a. RED: +10-16Vdc
b. BLACK: Ground
c. While light is powered, tap WHITE wire to ground to advance to
the next pattern (SEE pattern table at right)
d. Disconnect Power
3. Sync Lights
a. Once desired pattern has been selected for all light heads
connect all white wires and insulate with electrical tape.
4. Connect Master Switch for Application.
Flash Patterns
Pattern Name 1 Light Alternating 2 Lights
Simultaneous
2 Lights
F.P.M.
(Flashes /
Minute)
1. Quint x x x 70
2. Warp x x x 350
3. Inter-Cycle Flash x x
4. Double Flash x x x 70
5. Quad Flash x x x 80
6. PowerPulse™ x x x 180
7. RoadRunner™ x x x 113
8. Q-Switch™ x x
9. RoadRunner™ Steady Burn x x 113
10. Quad Steady Burn x x 80
11. E-Ideal Single Flash x x x 200
12. E-Ideal Double Flash x x x 146
13. Quad2 Flash x x x 67
14. Double2 Flash x x x 95
15. PowerRunner x x x
16. LCR Quint x x x
17. Warp3 x x x
18. Ultra Warp x x x 545
19. Thunder & Lightning x x
20. Lite Speed x x x 85
21. SuperSonic x x 170
22. LCR Lite Speed x x x
23. SuperSonic Ultra x x x
24. Tempo Shift x x x
25. Tempo Shift Warp x x x
26. SBE2 x x x 67
27. C2 x x x 200
28. U2 x x x 176
29. Cyclone2 x x x
30. Chameleon2 x x x
Tech Specs Intersector™
Flash Patterns: 30 Flash Patterns
Light Sync: Yes
Technology: 9 Gen3 LEDs
Mounting: Surface Mounts or Deck/ Grille
Bracket Mount
Input Voltage: 10 - 16 Vdc
Current Draw: less than 1.5 amps
Dimensions:
Width x Height x Depth
4” (98 mm) W x 2” (49 mm) H
x 2” (49 mm) D
Operating Temp.: -40° to +65° C / -104° to +149° F
Patents: US Design Patent No. D636,113
*Other Patents Pending*
Parts & Accessories:
Intersector SM Module PENT3BO
SM Intersector Bezel (Black) PNT3SMBB SM
SM Intersector Bezel (Chrome) PNT3SMBC SM
SM Intersector Bezel (White) PNT3SMBW SM
SM Intersector Gasket PNT3SMGS SM
Deck/ Grille Intersector Brkt (Black) PNT3DGBB

INTERSECTOR LED LIGHT
#ENT3(y)3(x) - SURFACE MOUNT
#PNT3DGBB DECK/ GRILLE BRACKET, BLACK
OPERATION:
For details on operation see page with ‘Flash
Patterns’ table on page 4.
!
WARNING
This product contains high intensity LED devices. To
prevent eye damage, DO NOT stare into the light
beam at close range.
IMPORTANT:
Supply power through a 3A fuse. For
Flashing mode, refer to function tables 1,2
and 3 on page 3. For slave/Remote Node
functionality such as when connected to
Blueprint, permanently connect the Green
wire to ground. Refer to Remote Node
functionality table on page 5.
Insulate all connections.
SURFACE MOUNT
INSTALLATION:
1. Establish a position on the vehicle on a level
surface. Orient the light output level on the
horizon.
2. Use the gasket provided as a template to
mark locations of wire and mounting
screws
3. Use a 5/8” diameter drill for the wire holes
4. Size pilot holes for mounting screws
appropiately.
5. Fasten light using bezel and mounting
screws. Do not torque mounting screws
beyond 20 in - lbs.
DECK/ GRILLE BRACKET
INSTALLATION:
(PURCHASED SEPARATELY)
1. Slide wire from Bezel through center
access hole in the gasket and bracket.
2. Next, position the Housing over the Bezel
and align the holes with the bracket.
3. Lastly, using the supplied 8-32 x 1”
screws fasten the assembly lightly. Do
not torque mounting screws beyond 20
in - lbs.
4. Establish a position on the vehicle on a level
surface. Orient the light output level on the
horizon.
5. Use the bracket provided as a template to
mark locations of mounting screws.
6. Size pilot holes for mounting screws
appropiately.
7. Fasten light using bezel and mounting
screws. Do not torque mounting screws
beyond 20 in - lbs.
SURFACE MOUNT
DECK/ GRILLE BRACKET MOUNT
BRACKET
GASKET
BEZEL
HOUSING
8/32 x 1” PHIL PAN SCREWS
Please see last page for Technical Specifications
•HIGH CURRENT interconnects must be properly terminated. Poor crimp quality can cause heat
build-up and fire. Follow crimp connector manufacturer instructions.
•DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to vehicle
Owner’s Manual for deployment zones.
•Unit may become hot to touch during normal operation.
•Failure to properly install connectors, fuses or wiring may cause vehicle failure or fire.
•Installation must only be performed by trained technician. Installer must determine vehicle wiring
configuration and proper integration of system.
•Use proper wire gauge. All power wires connecting to positive (+) or negative (-) battery terminal
or local chassis ground (-) must be sized to supply at least 125% of max. current and properly fused at
power source.
•Install protective grommets when routing wire through firewall or metal.
WARNING
WIRE HOOK-UP TABLE
WIRE COLOR: FUNCTION:
RED Table pg. 3
BLACK Ground
GREEN** Sync2 or Remote Node
Function*
WHITE to GROUND Wire Function
See Table pg. 2
WHITE to POWER Table pg. 3
RED/WHITE Table pg. 3
** To sync multiple Intersector or Nforce
lights connect the green wire from each
light together.
*Will NOT work w/ other sync products such
as Ghost, LED3, & 4-wire Intersector.
BLACK
RED
WHITE
GREEN
Sync
RED/WHITE
+Vdc
A FUSE
3
+Vdc
A FUSE
3
+Vdc
A FUSE
3
OPERATIONAL CONNECTIONS:

INTERSECTOR LED LIGHT
#ENT3(y)3(x) - SURFACE MOUNT
#PNT3DGBB DECK/ GRILLE BRACKET, BLACK
ADVANCE PATTERN
Flash pattern can only be changed when the LED module is in a flashing mode (disabled in cruise or steady ON functions). When the light is flashing, momentarily touch the white wire to ground for >250ms and <1s
(light will go steady high) then release. The flash pattern will advance to the next pattern. If the light module was at the last pattern, the pattern will reset to the 1st pattern.
BACKUP PATTERN
This function is only valid when the LED module is in a flashing mode (disabled in cruise or steady ON functions). When the light is flashing, momentarily touch the white wire to ground for >1s and < 2s (light will go
steady high, steady low) then release. The flash pattern will backup to the previous pattern. If the light module was at the first pattern, the pattern will change to the last pattern on the list.
COLOR SWAP
This function is only valid for dual color light modules and can only be changed when the light module is in a flashing mode (disabled for single color modules and when light module is operating in cruise or steady ON
functions). When the light is flashing, momentarily touch the white wire to ground for >2s and <3s (light will go steady high, steady low, off) then release. The light module will switch between Color Swap OFF and
Color Swap ON. When Color Swap is OFF, the 1st color will flash 1st on a dual color pattern. When Color Swap is ON, the 2nd color will flash 1st on a dual color pattern.
SIMULTANEOUS/ALTERNATE
This function can only be changed when the LED module is in a flashing mode (disabled in cruise or steady ON functions) and only has an effect when at least 2 LED modules have the green sync wire connected
together. When the light is flashing, momentarily touch the white wire to ground for >3s and <4s (light will go steady high, steady low, off, steady high) then release. The light module will switch between Simulta-
neous and Alternate each time this sequence is done. To have light modules flash simultaneously, both light modules need to be set to the same sequence type (Set-Up Table). To have light modules flash alternately,
the light modules need to be set to different sequence types (Set-Up Table).
PATTERN RESET
This function is only valid when the LED module is in a flashing mode (disabled in cruise or steady ON functions). When the light is flashing, momentarily touch the white wire to ground for >5s and <6s (light will go
steady high, steady low, off, steady high, steady low, off) then release. The flash pattern will reset to the 1st pattern in the list.
FACTORY RESET
This function is only valid when the LED module is in a flashing mode (disabled in cruise or steady ON functions). When the light is flashing, momentarily touch the white wire to ground for >6S and <7S (light will go
steady high, steady low, off, steady high, steady low, off, steady high) then release. The LED module will reset to: pattern=1, Function Table=1, Color Swap=OFF, Simultaneous.
SETUP TABLE
SECONDS USER INTERFACE
FROM TO VISUAL FEEDBACK ACTION TAKEN
0 1 STEADY-HIGH (60%) FORWARD ONE PATTERN
1 2 STEADY-LOW (30%) BACKWARD ONE PATTERN
2 3 OFF COLOR SWAP (OFF OR ON )
3 4 STEADY - HIGH (60%) SEQUENCE TYPE:
SIMULTANEOUS OR ALTERNATE
4 5 STEADY - LOW (30%) SET FUNCTION TABLE
5 6 OFF RESET TO PATTERN 1
6 7 STEADY-HIGH (60%)
FACTORY RESET (PATTERN 1, COLOR SWAP:
OFF, SIMULTANEOUS)
SEPARATE COLOR CONTROL: OFF
If held longer than 7 seconds, the light will go back to flashing the current
pattern and no action will be taken.

INTERSECTOR LED LIGHT
#ENT3(y)3(x) - SURFACE MOUNT
#PNT3DGBB DECK/ GRILLE BRACKET, BLACK
FUNCTION TABLE 1
WIRE LIGHT
RED RED/
WHITE WHITE SINGLE DUAL
+12V FLASH FLASH DUAL
+12 CRUISE STEADY COLOR
2
+12V +12V FLASH STEADY COLOR
2
+12V NO OP NO OP
+12V +12V LOW PWR
FLASH FLASH COLOR 1
+12V +12V CRUISE FLASH COLOR 2 FUNCTION TABLE 3
WIRE LIGHT
RED RED/
WHITE WHITE SINGLE DUAL
+12V FLASH FLASH DUAL
+12V FLASH LOW
PWR
FLASH DUAL LOW
PWR
+12V +12V FLASH LOW
PWR
FLASH DUAL LOW
PWR
+12V NO OP NO OP
+12V +12V FLASH LOW
PWR
FLASH DUAL LOW
PWR
+12V +12V FLASH LOW
PWR
FLASH DUAL LOW
PWR
+12V +12V +12V FLASH LOW
PWR
FLASH DUAL LOW
PWR
FUNCTION TABLES
Changing the function table is only enabled when the LED module is in a flashing mode (disabled in cruise or steady ON functions). The functional operation of the LED module can be changed while applying +vdc
to the Red wire with the black wire connected to ground. When the light is flashing, momentarily touch the White wire to ground for >4s and <5s (light will go steady high, steady low, off, steady high, steady low)
then release. The function table will now advance to the next table (table 1 to table 2, table 2 to table 3, or table 3 to table 1). Repeat above process until required function table is active.
FUNCTION TABLE 2
WIRE LIGHT
RED RED/
WHITE WHITE SINGLE DUAL
+12V +12V CRUISE FLASH DUAL
+12V STEADY
COLOR 1 STEADY COLOR 2
+12V +12V STEADY
COLOR 1 STEADY COLOR 2
+12V NO OP NO OP
+12V FLASH FLASH COLOR 1

INTERSECTOR LED LIGHT
#ENT3(y)3(x) - SURFACE MOUNT
#PNT3DGBB DECK/ GRILLE BRACKET, BLACK
FLASH PATTERNS
PATTERN
#
SINGLE
COLOR DUAL COLOR
1 QUINT
2 WARP
3 INTER-CYCLE
4 DOUBLE
5 QUAD
6 POWER PULSE
7 ROAD RUNNER
8 Q-SWITCH
9
STEADY-BURN / ROADRUNNER
(SEQUENCE TYPE 1: STEADY BURN,
SEQUENCE TYPE 2: ROADRUNNER)
10
STEADY-BURN DRIVER TITLE 13 QUAD
(SEQUENCE TYPE 1: STEADY BURN,
SEQUENCE TYPE 2: TITLE 13 QUAD)
11 QUAD 2
12 DOUBLE 2
13 RANDOM 1
14 RANDOM 2
SYNC 2
Syncronizing the flashing of multiple light modules is accomplished by connecting the Green wires of different light modules together. Up to 24 light modules can be connected for syncronized flashing. All light
module flash patterns must be set to the same flash pattern # to ensure proper operation. Refer to the Sequence Type section in Set-Up table to setup light modules to flash in alternate or simultaneous flash pattern.
NOTE: Will NOT work with with Sync products such as Ghost, LED3, 4-wire Intersector..

INTERSECTOR LED LIGHT
#ENT3(y)3(x) - SURFACE MOUNT
#PNT3DGBB DECK/ GRILLE BRACKET, BLACK
REMOTE MODE: FOR USE WITH bluePRINT SYSTEM ONLY
Connecting the Green wire to ground before applying power to the Red or Red/White wires will place the LED module into remote mode and the light output color will be directly controlled by the input wires as shown
below.
For Cruise mode or Low Power control of the LED module, the signal to the control wires must be 100 +/- 2Hz using the duty cycle inputs listed below to produce the light output.
Cruise Mode Duty Cycle
(@ 100Hz)
Input Light Output
40% OFF
50% 5%
60% 10%
Low Power Flash D.C.
(@ 100Hz)
Input Light Output
70% 30%
80% 40%
90% 50%
Intersector LED Light Remote Mode Functionality
Red Wire Red/Wht
Wire
Single Color Dual Color
Color
Swap=OFF
Color
Swap=ON
Color
Swap=OFF
Color
Swap=ON
Cruise - Cruise Color 1 Cruise Color 1 Cruise Color 2
- Cruise Cruise Color 2 Cruise Color 1
Cruise Cruise Cruise Color 2 Cruise Color 1
Flash - Flash Color 1 Flash Color 1 Flash Color 2
- Flash Flash Color 2 Flash Color 1
Flash Flash Flash Color 2 Flash Color 1
Steady ON - Steady ON Color 1 Steady ON Color 1 Steady ON Color 2
- Steady ON Steady ON Color 2 Steady ON Color 1
Steady ON Steady ON Steady ON Color 2 Steady ON Color 1
Cruise Flash
Flash Color 2/Cruise
Color 1 during OFF
cycle of Flash
Flash Color 1/Cruise
Color 2 during OFF
cycle of Flash
Cruise Steady ON Steady ON Color 2 Steady ON Color 1
Flash Steady ON Steady ON Color 2 Steady ON Color 1

INTERSECTOR LED LIGHT
#ENT3(y)3(x) - SURFACE MOUNT
#PNT3DGBB DECK/ GRILLE BRACKET, BLACK
Parts & Accessories:
Univ. Curved Surface Adaptors #PNT1CRVØ1 (pair)
Chevrolet Caprice Adaptors #PNT1CRVØ2 (pair)
Dodge Charger Adaptors #PNT1CRVØ3 (pair)
Ford Interceptor Sedan Adaptors #PNT1CRVØ4 (pair)
Ford Interceptor SUV Adaptors #PNT1CRVØ5 (pair)
Wedges (0°, 5° & 10°) #PNT1WDG (set of 3)
Intersector™ (light only) #PENT2BØ(x)
TECHNICAL SPECIFICATIONS
INTERSECTOR
Single Mount
Dimensions:
2.9” (74 mm) W x 1.9” (48 mm) H x 2.9” (74
mm) D
Input Voltage: 10 - 16 Vdc
CURRENT CONSUMPTION PER MODULE
10-16 Vdc
9 LED Single Color
18 LED Dual Color <1.25A @12.8 Vdc
AFTER POWER IS ON, touching the WHITE wire to the ground will allow you
to change variouse settings on the module. (refer to pages 3 & 4)
OVER-VOLTAGE PROTECTION
When an over-voltage condition is detected, the module will flash an over-voltage warning pattern of 50mS ON/950mS OFF to alert of the over-voltage condition and protect the electronics from damage due to heat/
voltage.
THERMAL COMPENSATION PROTECTION
The LED module is designed to provide maximum power output while providing protection to the electronic components by reducing the output power at extreme temperatures.