
1.800.338.7337 / www.soundosignal.com
77X3 / 6X4 P SERIES_WARNING
00KPJL 0822 REV B
WIRING AND TABLE INFORMATION (CONT.):
COLOR SWAP
This function is only valid for dual and tri-color warning light mod-
ules and can only be changed when the light module is in a flash-
ing mode (disabled for single color modules and when light mod-
ule is operating in cruise or steady ON functions). When the light
is flashing, momentarily connect the white wire to ground for >2S
and <3S (light will go steady high, steady low, off) then release.
The light module will switch between Color Swap OFF and Color
Swap ON. When Color Swap is OFF, the 1st color will flash 1st on
a dual/tri color pattern. When Color Swap is ON, the 2nd color will
flash 1st on a dual/tri color pattern.
SIMULTANEOUS/ALTERNATE
This function can only be changed when the LED module is in a
flashing mode (disabled in cruise or steady ON functions) and only
has an effect when at least 2 LED modules have the green sync
wire connected together. When the light is flashing, momentarily
connect the white wire to ground for >3S and <4S (light will go
steady high, steady low, off, steady high) then release. The light
module will switch between Simultaneous and Alternate each time
this sequence is done. To have light modules flash simultane-
ously, both light modules need to be set to the same sequence
type (Set-Up Table). To have light modules flash alternately, the
light modules need to be set to different sequence types (Set-Up
Table).
ADVANCE PATTERN
Flash pattern can only be changed when the LED module is in a
flashing mode (disabled in cruise or steady ON functions). When
the light is flashing, momentarily connect the white wire to ground
for >250mS and <1S (light will go steady high) then release. The
flash pattern will advance to the next pattern. If the light module
was at the last pattern, the pattern will reset to the 1st pattern.
SETUP TABLE
SECONDS USER INTERFACE
FROM TO VISUAL FEEDBACK ACTION TAKEN
0 1 STEADY-HIGH (60%) FORWARD ONE PATTERN
1 2 STEADY-LOW (30%) BACKWARD ONE PATTERN
2 3 OFF COLOR SWAP (OFF OR ON )
3 4 STEADY - HIGH (60%) SEQUENCE TYPE:
SIMULTANEOUS OR ALTERNATE
4 5 STEADY - LOW (30%) SEE FUNCTION TABLE
5 6 OFF RESET TO PATTERN 1
6 7 STEADY-HIGH (60%) FACTORY RESET (PATTERN 1, COLOR SWAP: OFF,
SIMULTANEOUS) SEPARATE COLOR CONTROL: OFF
7 8 STEADY - LOW (30%) LOCK OUT WHITE CONFIGURATION WIRE
If held longer than 8 seconds, the light will go back to flashing
the current pattern and no action will be taken.
BACKUP PATTERN
This function is only valid when the LED module is in a flashing
mode (disabled in cruise or steady ON functions). When the light
is flashing, momentarily connect the white wire to ground for >1S
and < 2S (light will go steady high, steady low) then release. The
flash pattern will backup to the previous pattern. If the light mod-
ule was at the first pattern, the pattern will change to the last pat-
tern on the list.
PATTERN RESET
This function is only valid when the LED module is in a flashing
mode (disabled in cruise or steady ON functions). When the light
is flashing, momentarily connect the white wire to ground for >5S
and <6S (light will go steady high, steady low, off, steady high,
steady low, off) then release. The flash pattern will reset to the 1st
pattern in the list.
FACTORY RESET
This function is only valid when the LED module is in a flashing
mode (disabled in cruise or steady ON functions). When the light
is flashing, momentarily connect the white wire to ground for >6S
and <7S (light will go steady high, steady low, off, steady high,
steady low, off, steady high) then release. The LED module will
reset to: pattern=1, Function Table=1, Color Swap=OFF, Simul-
taneous.
LOCKOUT CONFIGURATION WIRE
This function will disable the wire tap configuration mode that
is activated by holding the white wire to ground. The lock out is
activated by applying ground to the white wire for >7 seconds and
<8 seconds per the table below. The function can be disabled by
tapping the wire to ground and releasing 8 times within 5 seconds.
The light will flash 8 times when the feature is enabled or disabled
to notify the user of a setting change.