Soyal AR-721KP User manual

SOYAL
ACCESS CONTROL SYSTEM
®AR-721KP
V110810
EXIT 1 2 3 4 5 6
EXIT
1
2
3
4
5
6
7
f x2
4
N.C.
N.O.
COM
ERG
DLY
GND
12V
CN2
CN1
SGND SW 1 SW 2 N.C. N.O. COM
1
2
3
4
5
6
7
COM
COM
N.C.
SGND
N.O.
EGR
DLY
12V
GND
GND
12V
GND
12V
N.O.
N.O.
CN1
CN2
Specication
Front Panel Indicators
Pull the cables from the square hole of the mounting plate.
Use a screwdriver to screw the base onto the wall.
Connect the terminal cables to the body and attach the body to the mounting plate.
Assemble the covers with the Allen key and screws (accessories supplied).
Turn on the power and LED will light and beep will sound.
Installstion
Contents
1Product 2User Guide 4Specication
3Tools
The unit should make a beep sound when any key on the keypad is depressed.
If no key is made within 30 seconds, it will automatically exit the programming mode.
In the programming mode: LED lightgreen and ash rapidly, it means that the unit waits for entering.
In the programming mode: LED is red and ash rapidly, it means the reader is busy.
One beep sound mean acknowledge, two beep sounds mean not acknowledge.
Don’t equip controller and lock with the same power supply.
The power for controller may be unstable when the lock is
activating, that may make the controller malfunction.
The standard installation: Door relay and lock use the same
power supply, and controller use independent power supply.
Installation Notice
CN2CN1
Wire Appllcation Wire Description
Relay_A
N.C. 1 N.C.
N.O. 2 N.O.
COM 3 COM
Exit Switch EGR 4 Negative Trigger Input for Relay_A
DLY 5 Negative Trigger Input for Relay_B
Power VIN- 6 DC Power GND
VIN+ 7 DC Power 12V
Wire Appllcation Wire Description
Relay_B
COM 1 COM
N.O. 2 N.O.
N.C. 3 N.C.
Tamper
Switch
SW 4 N/O or N/C select via jumper
SW 5 COM
SGND SGND 6 Signal Ground
Terminator
Electric Bolt Keypad
Request To Exit
Request To Exit
POWER
12VDC
POWER
12VDC
POWER
12VDC Diode
Electric Strike
Wiring Diagram
Users 500 Power consumption < 2W Memory EEPROM Weight(g) 100±10
Digits 3-6 Operating Temperature -20℃to +60℃ Color Gray/Silver Housing Material ABS
Power Supply 9-16VDC / 100mA Indicator 1 Bi-Color LED&1Beeper Dimensions(mm) 111(L) x 77(W) x 26(H)
Delete user(s) code and Enable to system
Delete (Remove) a User Code from the system
Press 123456 (or Master Code) → 14 UUU →Done ( A green light and beep means that the user code was deleted. )
[e.g.] Delete User address 10
： Access programming mode → 14 010 →Done
Delete (Remove) all Users Codes from the system
Press 123456 (or Master Code) → 29 29 →Done (The LED ash red during 1 second to mean that the system is deleting all user codes.
Then a green light and beep means that all user codes were deleted. )
Delete (Remove) a User Code from the controller
If you would like to delete all user codes. Remove the AR-721KP from the mounting plate. Press and hold the reset switch 10 seconds (RESTER, on
the KEYPAD circuit board). LED light green during 5 seconds and six beep sounds mean that all user are deleted.
Up to 500 pin-codes programmable from keypad.
Two access groups, each have request to exit inputs to control.
Default value: rst group= 000~249 (Relat_A); second group= 250~499 (Relay_B).
2 relay outputs contact support latching or momentary outputs.
Built-in watchdog to prevent the system from halting.
Built-in tamper switch, include external security system interface.
Bell output, Press + together for bell using. (Optional)
Keypad will be locked for 30 seconds while continuous error operation.

V110810
Keypad
Programming
C. Add a User Code to the system
B. Set up user number corresponding to door relay
D. Set the door relay-1 release time
E. Set time out value
F. Set keypad lock of continuous error operation
Enable a (range of) User(s) Code to the system
Press 123456 (or Master Code) → 11 SSS EEE → Done (A green light and beep means that the user code(s) was enabled. )
[e.g.] Enable User code 58 to the system
：
Access programming mode → 11 058 058 → Done
[e.g.] Enable User code 1 to 10 to the system
：
Access programming mode → 11 001 010 → Done
[e.g.] Set user code 123 to user 001
：
Access programming mode → 12 001 123 → Done
Access programming mode → 12 UUU PPPPPP
UUU(User address)
：
001~254
；
PPPPPP(User Code)
：
The user code must be 3 to 6 digits in length and the key # cannot be used in a code.
[e.g.] Set user code 123456 to user 002
：
Access programming mode → 12 002 123456 → Done
Access programming mode → 01 UUUU UUUU=User address (Default value = 0250)
[User number 0000~0249 operates Relay_A; User number 0250~0499 operates Relay_B.]
Access programming mode → 04 TT TT = 00~09 (0~0.9) seconds; TT = 10~49 (1~4.9) seconds
Access programming mode → 06 PPP PPP = 000 (Disable) / PPP = 001 (Enable) [If use two access groups, places set disable.]
G. Set Door bell ( + Door Ring)
Access programming mode → 05 T T = 3~9 (times); T = 0 (Close this Function)
[e.g.] Set three incorrect user code are entered
：
Access programming mode → 05 3 → Done
A. Entering and Exiting Programming Mode
Changing the Master Code
Access programming mode → 09 PPPPPPRRRRRR [Input the 6-digit new master code twice.]
[e.g.] If want to changing the Master Code= 876112, input 123456 → 09 876112876112
Exiting
Input
Entering
Input 123456 or PPPPPP
[e.g.] The Default Value= 123456, if already changed the Master Code= 876112, input 876112 → Access programming mode
Access programming mode → 02 TTT
Set door relay_B, enter 03.
TTT = 000 Latch(Toggle) / TTT = 001~600 (001~600) seconds.
TTT =601~609 (0.1~0.9) seconds.
Command List
Function Command Exposition
Entering programming mode PPPPPP PPPPPP: Master Code, (Default value: 123456)
Exiting programming mode
User number corresponding to door relay 01 UUUU UUUU＝User address, (Default value: 0250); User before the
250th is the rst group, the other is the second group.
Relay_A time setting 02 TTT TTT
＝Door relay time；000 (Output constantly)
001~600＝1-600 Sec.；601~609＝0.1~0.9 Sec.
Relay_B time setting 03 TTT TTT
＝Door relay time；000 (Output constantly)
001~600＝1-600 Sec.；601~609＝0.1~0.9 Sec.
Set time out value 04 TT TT
＝Keypad operate during time
Range
：00 ~ 09 (0 - 0.9) Sec.；10 ~ 49 (1 - 4.9) Sec.
Set keypad lock of continuous error operation 05 T T
＝Continuous error times ：3 ~ 9 (Times) ；T ＝0 (Disable)
Door bell 06 PPP PPP＝000 ( Disable ) / PPP＝001 ( Enable )
Master code settings 09 PPPPPPRRRRRR PPPPPP= New master code
RRRRRR= Repeat the new master code
Suspend or delete user code 10 SSS EEE SSS= starting user address ; EEE= ending user address
Recover user code 11 SSS EEE SSS= starting user address ; EEE= ending user address
Add a User Code to the system 12 UUU PPPPPP UUU＝User address
PPPPPP＝3 to 6 digits
Delete (Remove) a User Code 14 UUU UUU＝User address
Delete (Remove) all Users Codes 29 29
Factory Reset by its commands
If the master code is forgotten it can be restored to the factory default. Remove the AR-721KP from the mounting plate. Press and hold the reset switch
5 seconds. LED light green during 2.5 seconds and ve beep sounds mean that master code have restored to the factory default 123456.
Delete (suspend) a (range of) User(s) Code from the system
Press 123456 (or Master Code) → 10 SSS EEE →Done (A green light and beep means that the user code(s) was disabled. )
[e.g.] Delete (suspend) User code 58
：
Access programming mode → 10 058 058 → Done
[e.g.] Delete (suspend) User code 1 to 10
：
Access programming mode → 10 001 010 → Done