Soyal AR-327-E User manual

SOYAL
ACCESS CONTROL SYSTEM
®AR-327-E / 727-E V200114
CN4 CN5 CN7
CN6 CN3 CN2
AR-821RB
AR-821RB
CN4 CN5 CN7
CN6 CN3 CN8
6
5
4
3
2
1
CN11
6
5
4
3
2
1
CN9
8
7
6
5
4
3
2
1
CN5
CN3
8
7
6
5
4
3
2
1
CN4
2
1
CN6
7
6
5
4
3
2
1
CN7
4
3
2
1
CN8
7
7
6
6
5
5
4
4
3
3
2
2
1
1CN18
CN2
CN18
327-E
327-E
727-E
727-E
Wire Application Wire Color Description
1 --- ---
2 --- ---
TCP/IP Module
Output
3
Orange White
Net - TX+
4Orange Net - TX-
5Green White Net - RX+
6Green Net - RX-
7 --- ---
Wire Application Wire Color Description
RS-485 for Lift
Controller
1Thick Green RS-485(B-)
2Thick Blue RS-485(A+)
Wire Application Wire Color Description
Anti-Tamper
Switch
1Red N.C.
2Orange COM
3Yellow N.O.
Wire Application Wire Color Description
Power 1 Red DC 12V Output
Security trigger signal 2Purple Security trigger signal Output
Arming 3 Red White Arming Output
Duress 4 Yellow White Duress Output
(AR-327H-V5 By
order)
Wire Application Wire Color Description
Lock Relay 1Blue White (N.O.)DC24V1Amp
2
Purple White (N.C.)DC24V1Amp
Lock Relay COM 3White (COM)DC24V1Amp
Door Contact 4Orange Negative Trigger Input
Exit Switch 5Purple Negative Trigger Input
Alarm Relay 6Gray N.O./N.C. Optional (by jumper)
Power 7Thick Red DC 12V
8Thick Black DC 0V
Wire Application Wire Color Description
Beeper 1Pink Beeper Output 5V/100mA, Low
LED 2Yellow Red LED Output 5V/20mA, Max
3Brown Green LED Output 5V/20mA, Max
Door Output 4Blue White Transistor Output Max. 12V/100mA
(Open Collector Active Low)
Wiegand 5Thin Green Wiegand DAT: 0 Input
6Thin Blue Wiegand DAT: 1 Input
WG Door Contact
7Orange Negative Trigger Input
WG Exit Switch 8Purple Negative Trigger Input
(Optional)
(Optional) (Optional)
(Optional)
Main PCB 727H-V5 LCD-PCB
1.Tubing: The communication wires and
power line should NOT be bound in the
same conduit or tubing.
2.Wire selection:Use AWG 22-24
Shielded Twist Pair to avoid star wiring
,CAT 5 cable for TCP/IP connection.
Don’t equip reader and lock with the
same power supply. The power for
reader may be unstable when the lock
is activating, that may make the reader
malfunction.
3.Power supply:The standard
installation: Door relay and lock use the
same power supply, and reader use
independent power supply.
Attach the water proof strip to the mounting plate.
Pull the cables from the square hole of the mounting plate.
Use a screwdriver to screw the base onto the wall.
Connect the terminal cables to the body and attach the body to the mounting plate.
Assemble the covers with the Allen key and screws (accessories supplied).
Turn on the power, the LED will light and hear the beep sound, you will see "Ready""
on LCD board.
2User Guide 1Products 3Terminal Cables 4Tools 5Optional
AR-721RB
Digital Relay
Water proof Strip
2User Guide
1Products 3Terminal Cables 4Tools 5Optional
AR-721RB
Digital Relay
TCP/IP Module
and Cable
Water proof Strip
3
1
2
5
4
3
1
2
4
5
Contents
AR-327-E:Touch-panel Metal Case
AR-727- E
Installation Notice
AR-327-E
Pull the cables from the square hole of the mounting plate.
Use a screw to the mounting plate onto the wall.
Attach the water proof strip to the body, then connect the terminal cables to the body
and attach the body to the mounting plate.
Use the Allen key and screws (accessories supplied) to assemble the body onto the
mounting plate.
Turn on the power, the LED will light and hear the beep sound, you will see "Ready""
on LCD board.
AR-727- E
Connector Table
Cable: CN4
P1
Cable: CN6
P4
P2Cable: CN5
P6Cable: CN8
P5Cable: CN3
Cable: CN7
P3

V200114
AR-327-E AR-727-E
18/02 FRI Duty:0 18/02 FRI Duty:0
10:49:34 10:49:34
Ready...... Ready......
P
W
R
E
R
R
02 24
14 : 49 : 04
FRI
Duty : 0
1
2
3
4
5
6
7
8
E
12V
GND
Exit Switch
12V
GND
12V
GND
N.O.
GND
N.O.
COM
PB
12V
GND
CN4
EXIT
1
2
3
4
5
6
7
8
12V
GND
12V
GND
12V
GND
N.O.
GND
N.O.
COM
PB
12V
GND
CN4
EXIT
Door Contact
ALM
12V
GND
12V
GND
12V
GND
12V
GND
N.C.
CN4
N.C.
N.O.
COM
CTL
12V
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
E
12V
GND
12V
GND
12V
GND
12V
GND
PB
PB
COM
COM
N.O.
N.O.
CN4
CN4
12V
GND
12V
GND
PB
COM
N.C.
CN4
EXIT EXITEXIT
EXIT
N.C.
COM
PB
12V
GND
N.O.
N.O.
COM
N.C.
V+
V-
LCD Access Controller
Optional Cables
Connect to Electric Bolt
Wiring Diagram
Controller
RTE
POWER
12VDC
POWER
12VDC
Controller
RTE
POWER
12VDC
POWER
12VDC
Magnet Lock
Connect to Magnet Lock
Connect to Electric Strike Connect to Door Contact
Controller
RTE
POWER
12VDC
POWER
12VDC
Electric Strike
If any re emergency, the people can escape by press a switch to open all doors
RTERTE
RTE
POWER
12VDC
POWER
12VDC
Electric Strike Electric Bolt
Fire Emergency
Transistor
IN4007
Transistor
IN4007
Transistor
IN4007
Magnet Lock
Controller
POWER
12VDC
POWER
12VDC
Alarm
Relay Outpot Module
Door Contact
Front Panel & Indicator
Data
Week
Work Status
Data [e.g.] 02/24←→02 24(Network Connected)
Week
Work Shift Status
Esc/Quit
Up
Down
Left
Right
Enter/OK
Power(Green)
Alarm(Red)
Arming (Green)
Esc/Quit
Up
Down
Left
Right
Enter/OK
OK(Green)
Error (Red)
In processing (Green)
Power(Green)
Alarm(Red)
Arming (Green)
Wire Application Wire Color Description
TTL Port for
Lift Control or Voice
Module
(*Required speaker
8Ω / 1.5W (Max.
2W)
1Black DC 0V
2Yellow TX
3White TE
4Orange RX
5Red DC 5V
6 --- ---
Wire Application Wire Color Description
HID ProxII RF
Module
1Orange
ANT 1
2 Purple ANT 2
3Black DC 0V
4Red DC 5V
5Blue Wiegand DAT: 1 Input
6Green Wiegand DAT: 0 Input
7White --
Cable: AR-327-E: CN10 / 727(H-V5): CN18 P8Cable: CN11(Optional:Lift Control w/ AR-725L485; SW:RS485-2) P7
CN9 (Optional:Voice Module; SW:RS485-3)
P9
OK(Green)
Error (Red)
In processing (Green)
POWER
12VDC

SOYAL
ACCESS CONTROL SYSTEM
®AR-327-E / 727-E V200114
EXIT
N.C.
N.O.
COM
CTL
12V
GND
PB
12V
GND
12V
GND
N.O.
12V
GND
12V
GND
DDR
CN4
CN8
CN2 AR-721RB
12V
327H-V5
727H-V5
1
2
3
4
5
6
7
8
1 2 3 4
N.C.
N.O.
COM
CTL
12V
E
BZ
RLED
GLED
WG 1
12V
GND
1
2
3
6
12V
GND
Exit Switch
12V
GND
CN5
CN4
BZ
RLED
GLED
Door Output
WG 0
WG 1
WG-DS
WG-PB
7
8
N.C.
EXIT
1
2
3
4
5
6
7
8
5
4
WG 0
RTE
Controller
Reader
RTE
POWER
12VDC
POWER
12VDC
POWER
12VDC
POWER
12VDC
Door Contact
Strengthen security with AR-721RB
Electric Bolt Electric Bolt
Connect to Reader
Access programming mode → Add/Delete → Add -> RF-Learn → Input 5/6-digit user address
→ Input Tag Units(pcs) → Close Tag into RF Area
※ If adding a batch of Sequential tags, please input Tag Units(pcs) in the quantity of the tags and present the
tag with the lowest card code to the access controller.
1 2
Adding Tag by RF Learn Function
Tag Information
SITE CODE
CARD CODE
SITE CODE
CARD CODE
Adding and Deleting Tag
※ User capacity: 16384 (00000~16383)
Access programming mode → Add/Delete → Add -> Card ID → Input 5/6-digit user address → Input Site Code → Input Card Code
11
Adding Tag by Tag ID
Access programming mode → Add/Delete → Delete -> Addr → Input Starting address → Input Ending address
1 5
Deleting User Address
Access programming mode → User Setting → Access Mode → Input User Address → 0: Invalid; 1: Card ; 2: Card or PIN; 3: Card & PIN
2 2
Setting up the access mode
Access programming mode → Add/Delete → Delete -> ID # → Input Site Code → Input Card Code
1 6
Deleting Tag by Tag ID
D. PIN Code
C. Initial setup
Access programming mode → User Setting → Password → Input
5/6-digit user address → Input 4-digit PIN (0001~9999) → Succeeded Or via
701Client set it on Users screen
21
Node ID of Reader Setting
Access programming mode → Parameters[1] → Node
ID → Input New Node ID : 1~254 (default value:001) →
Main Door Number : 0~255 → WG1 Door Number : 0~255
→ Show UID (0=No,1=WG,2=ABA,3=HEX) → Enable
DHCP(0:No,1:En,2=Exit) → Succeeded
3 1
Language Setting
Access programming mode → Tools → Language →
0EN → Succeeded → Initial system...
5 1
F. Enable Voice Module (supporting version : F/w Ver 3.02
or later)
Software Setting
701 Server
or
Programming
B. Entering and Exiting Programming Mode
Changing the Master Code
Access programming mode → Tools → Master Code →
Input the 6-digit new master code → Succeeded
5 2
A. Keyboard Lock/ Unlock
Lock/ Unlock
Press and , and at the same time to lock keyboard.
Press again to unlock.
Entering
Input 123456 or PPPPPP
[e.g.] The Default Value= 123456. If already changed the Master
Code= 876112, input 876112 → Access programming mode
P.S.If entering no instruction within 30 sec., it will automatically
leave the programming mode.
Exiting
Press the repeatedly → Quit or Quit and Arming
(Please refer to alarm / arming setting)
6 7
E. Setting up the alarm / arming
Conditions: 1. Arming enabled 2.Alarm system connected
Application:
1. Door open too long: Door is open longer than door relay time plus door close
time.
2. Force open (Opened without a valid user card): Access by force or illegal
procedure.
3. Door position abnormal: When power is o󰀨 and then on, reader on arming
before power o󰀨.
Step 1. Click "Read."
Step 2. Select "Card
Reader" in RS485-2
section.
Step 3. Click "Write" to
nish the setting.
Hardware setting
Access programming mode → Tools → Ext. Comm Port → Voice
552

V200114
RESET
LCD Access Controller
Enable/Disable the arming status:
Standby Mode
Access Programming mode
Card only Card or PIN Card and PIN
Open the door
Present the tag to reader → Input
4 digits arming PWD →
Input user address → Input 4
digits individual PWD → →
Input 4 digits arming PWD →
Present the tag to reader → Input
4 digits individual PWD → →
Input 4 digits arming PWD →
Enable: Access programming mode → Quit & Arming
7Disable: Access programming mode → Quit 6
No open the door
→ Input 4 digits arming PWD
→ Present the tag to reader
E. Setting up the alarm / arming
Restoring Factory Settings
Reset all device parameters and user card data
Reset IP Setting:
When the device's power is on, press the
【
RESET】 button the main board untill the ERR (Red) LED of
screen lights up. (Reference to picture)
※ After operation as above, you will hear the long reminder sound,and wait until the
sound disappear then reset the power of the controller,the device will restore factory setting.
Manu Tree
5. Tools
1. Language
2. Master Code
3. Master Range
4. Terminal Port
5. Ext.Comm Port
6. Open Time Zone
7. Informations
8. Clock Setting
9. Daily Alarm
0. UART Port
A. Event Logs
6. Quit
7. Quit & Arming
4. Parameters[2]
1. Auto Relock
2. Egress(R.T.E)
3. Miscellaneous
4. Force Open
5. Close & Stop
6. Anti-pass-back
7. Duress Code
8. Password Mode
9. Factory Reset
3. Parameters[1]
1. Node ID
2. OnO󰀨 OpenZone
3. Door Relay Tm
4. Door Close Tm
5. Alarm Relay Tm
6. Alarm Delay Tm
7. Arming Delay Tm
8. Arming PWD
9. PIN&UID format
2. User Setting
1. Password
2. Access Mode
3. Extend Options
4. Single Floor
5. Multi Floor
1. Add/ Delete
1. Add > Card ID
2. Add > RF Learn
3. Suspend > Address
4. Suspend > ID #
5. Delete > Address
6. Delete > ID #
7. Recover > Address
8. Recover > ID #
9. Antipass Group
Reset all device parameters and user card data:
Access programming mode → Parameters2 → Factory Reset →0 : System Param ;
1 : User Setting ; 2 : System & User
94
IP Setting
Log-in User Password
When you choose the "Networking Setting" or "User Password" at rst.
Log-in window will pop out and please input
※ At the Factory Default
User name: SuperAdm
Password: 721568
Open your Web Browser and input factory default IP
address: http://192.168.1.127
Networking Setting
You will nd initial IP Address 192.168.1.127 and check
MAC Address is the same as sticker on Ethernet Module
device. Please revise IP address you want, and then click
“Update” button. After updating the IP, please re-connect
the Web Browser by new IP address.
User Password
The password composes of 10 characters at most, it can be
either A~Z or 0~9.
Change the log-in password to lock the IP setting of
Ethernet Module.
If the IP address of AR-327-E
/ 727-E has changed We must
enter the new IP address.